2009 Toyota RAV4
The 2009 Toyota RAV4 came with 2 engines: 2.5 L 4-cylinder, 3.5 L 6-cylinder. It gets 21 to 24 MPG combined depending on the engine, per the EPA. 15 recall campaigns and 327 owner complaints are on record.
Specs
| Cylinders | 4 |
|---|---|
| Transmission | Automatic · 4 speeds |
| Drivetrain | AWD |
| Length | 132 mm (5.2 in) |
| Width | 540 mm |
| Curb weight | 1,450 kg (3,197 lb) |
| Seats | 5 |
| Body style | Sport Utility Vehicle - 2WD |
Specs: average of the cars of this model first registered in 2009 in the Netherlands (RDW vehicle register).
For sale in United States
Safety
Crash-test results across markets. They can vary by version and equipment.
Fuel economy (MPG)
🇺🇸 Local dataBy version
| Engine | Transmission | Drivetrain | City | Highway | Combined |
|---|---|---|---|---|---|
| 2.5 L 4-cylinder | Automatic · 4 speeds | AWD | 21 MPG | 27 MPG | 24 MPG |
| 2.5 L 4-cylinder | Automatic · 4 speeds | Front-wheel (FWD) | 22 MPG | 28 MPG | 24 MPG |
| 3.5 L 6-cylinder | Automatic · 5 speeds | AWD | 19 MPG | 26 MPG | 21 MPG |
| 3.5 L 6-cylinder | Automatic · 5 speeds | Front-wheel (FWD) | 19 MPG | 27 MPG | 22 MPG |
EPA figures for each version sold in the U.S.
Recalls
Consequence · Remedy
Failure of the rear tie rod could cause a loss of vehicle control, increasing the risk of a crash.
Toyota will notify owners and dealers will replace both rear suspension arms and encapsulate the locknuts, free of charge. The recall began on September 30, 2016. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's numbers for this recall are G0V for Toyota vehicles and GLK for Lexus vehicles. Note: This recall supersedes recall 13V-383, in which some vehicles were only inspected, sealed, and did not have both arms replaced. The affected vehicles were previously recalled under 13V-383, but did not have both rear suspension arms replaced at that time. Those vehicles need to have both arms replaced as part of this recall remedy.
Consequence · Remedy
If damaged, the copper strand heating element may short circuit, increasing the risk of a fire.
SET will notify owners, and dealers will disconnect the seat heaters, free of charge, and refund the purchase price of the seat heater accessory. The recall began on July 14, 2016. Owners may contact SET customer service at 1-866-405-4226. SET number for this recall is SET16B.
Consequence · Remedy
A cut seat belt may not properly restrain the seat occupant, increasing their risk of injury in a crash.
Toyota will notify owners, and dealers will install a protector over both rear seat cushion frames, free of charge. The recall began on June 24, 2016. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is G0F.
Consequence · Remedy
If the sliding electrical contacts are not protected by lubricant, debris and moisture that get into the switch may cause a short circuit and the switch assembly may overheat and melt, increasing the risk of a fire.
Toyota will notify owners, and dealers will inspect the switch, applying a lubricant if no abnormality is found. If abnormality is found, the PWMS circuit board will be replaced, free of charge. The recall is expected to begin December 20, 2015. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is C0M.
Consequence · Remedy
Over time, the dripping water may cause corrosion and wear at the joint, potentially resulting in the separation of the wiper linkage. Once this occurs, the wipers would not function, reducing driver visibility and increasing the risk of a crash.
Toyota will notify owners, and dealers will replace the water diverter channel. In addition, a new wiper linkage with a wiper motor crank arm will be installed. The wiper linkage will have a protective cover over the wiper linkage joint to minimize water splash and a retainer ring to prevent the wiper arm from separating from the wiper motor. The recall began on November 7, 2016. Owners may contact Toyota's customer service number at 1-800-331-4331.
Consequence · Remedy
Damage to the seat heater wiring could cause the wires to short, increasing the risk of the seat burning and causing personal injury to the occupant.
SET will notify owners, and dealers will disconnect the heaters with copper strand heating elements and refund the purchase price of the seat heater accessory, free of charge. The recall is expected to began in January 2015. Owners may contact SET customer service at 1-866-405-4226.
Consequence · Remedy
Failure of the rear tie rod could cause a loss of vehicle control, increasing the risk of a crash.
Toyota will notify owners, and dealers will inspect the tie rods and replace any that have rust or corrosion on the alignment adjustment threads. All of the rear tie rods will then be encased in an epoxy to prevent future environmental damage. Due to limitations in parts, the recall remedy will be launched in phases from September 2013 through mid-April 2014. All owners will receive notification of the recall, with most receiving second notifications when parts are available in their area. IMPORTANT: This recall supersedes Toyota and Lexus recall 12V-373. All vehicles that have been inspected and remedied under the previous recall need to be re-inspected and have the appropriate remedy applied.
Consequence · Remedy
If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.
Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
Consequence · Remedy
If the switch overheats, it may melt, possibly resulting in a fire.
Toyota will notify its owners, and dealers will inspect the switch and apply a special grease that inhibits heat build up or replace any switch damaged by the defect, free of charge. Toyota owners that experience a problem with a switch should not attempt to make repairs, but should contact their Toyota dealer or the Toyota Customer Experience Center at 1-800-331-4331. General Motors will contact the Pontiac Vibe owners affected by this recall and GM dealers will inspect and repair switches as necessary. Those owners may contact Pontiac Customer Care at 1-800-762-2737.
Consequence · Remedy
Failure of the rear tie rod could cause a loss of vehicle control, increasing the risk of a crash.
Toyota will notify owners, and dealers will inspect the rear tie-rod nut for looseness and replace any suspect tie-rod found loose. Dealers will also affix instructions in multiple places to prevent improper servicing in the future. The recall began on November 30, 2012. Owners may contact Toyota at 1-800-331-4331 or Lexus at 1-800-255-3987.
Consequence · Remedy
A STUCK OPEN ACCELERATOR PEDAL MAY RESULT IN VERY HIGH VEHICLE SPEEDS AND MAKE IT DIFFICULT TO STOP THE VEHICLE, WHICH COULD CAUSE A CRASH, SERIOUS INJURY OR DEATH.
THE REMEDY IS NOW AVAILABLE. THE SAFETY RECALL BEGAN EARLY APRIL 2011. THE REMEDY WILL INVOLVE MODIFICATION OR REPLACEMENT OF THE ACCELERATOR PEDAL AND REPLACEMENT OF ANY TOYOTA ALL-WEATHER FLOOR MAT. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331 OR LEXUS AT 1-800-255-3987.
Consequence · Remedy
A DRIVER MAY OVERLOAD A VEHICLE WHICH MAY INCREASE THE RISK OF A CRASH.
DEALERS WILL MAIL TO CONSUMERS THE CORRECTED LABEL OR THE CUSTOMER WILL HAVE THE OPTION FOR DEALERS TO INSTALL THE LABEL FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 27, 2010. OWNERS MAY CONTACT SOUTHEAST TOYOTA AT 1-800-301-6859.
Consequence · Remedy
THIS DOES NOT MEET THE STANDARD REQUIREMENTS.
DEALERS WILL MAIL TO CONSUMERS THE CORRECTED LABEL OR THE CUSTOMER WILL HAVE THE OPTION FOR DEALERS TO INSTALL THE LABEL FREE OF CHARGE. DEALERS WILL ALSO CORRECT THE OWNER'S MANUAL. THE SAFETY RECALL BEGAN ON MAY 27, 2010. OWNERS MAY CONTACT GULF STATES TOYOTA AT 713-580-3300.
Consequence · Remedy
THE ACCELERATOR PEDAL MAY BECOME HARD TO DEPRESS, SLOW TO RETURN TO IDLE, OR, IN THE WORST CASE, MECHANICALLY STUCK IN A PARTIALLY DEPRESSED POSITION, INCREASING THE RISK OF A CRASH.
DEALERS WILL INSTALL A REINFORCEMENT BAR IN THE ACCELERATOR PEDAL WHICH WILL ALLOW THE PEDAL TO OPERATE SMOOTHLY. GM WILL NOTIFY OWNERS FOR THE PONTIAC VIBE PLEASE SEE 10V-018. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON FEBRUARY 5, 2010 AND WILL BE COMPLETED ON MARCH 15, 2010. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
Consequence · Remedy
INCORRECT LOAD CARRYING CAPACITY MODIFICATION LABELS COULD RESULT IN THE VEHICLE BEING OVERLOADED, INCREASING THE RISK OF A CRASH.
TOYOTA WILL NOTIFY OWNERS AND PROVIDE THEM WITH A NEW, ACCURATE LABEL TO BE INSTALLED OVER THE INACCURATE LABEL FREE OF CHARGE. THE SAFETY RECALL BEGAN ON AUGUST 18, 2009. OWNERS MAY CONTACT TOYOTA AT 1-888-270-9371.
It may not apply to vehicles sold in your country. Check with your VIN at the source.
Details
Issue: This recall is for certain block heater kits installed on certain vehicles or sold as accessories at Toyota or Lexus dealerships. On certain vehicles, the engine block heater cable may not have enough heat protection and could be damaged by high temperatures. If this happens, the cable could short circuit while plugged in, and cause the wiring to overheat or melt. Note: This recall only affects the following block heater/cord part numbers: C014003034 PK5A408J09 PU14000904 C014003151 PK5A408J13 PU14000905 C014000885 PK5A489J11 PU14000907 C014000888 PK5A489J22 PU14000909 C014000907 PK5A410H00 PU14000911 C014100904 PU14000900 PU14000913 C014100907 PU14000901 PU14003571 C014100911 PU14000902 PK5A489J14 PK5A408J05 PU14000903 Safety Risk: Engine block heater wiring that overheats or melts could create the risk of a fire. Corrective Actions: Toyota recommends that you should stop using the engine block heater immediately. Toyota will notify owners by mail and instruct you to take your vehicle to a dealer to disable the engine block heater. For some vehicles, the corrective actions for this recall are under development. For others, a new engine block heater cannot be installed, and the owner will receive a refund of the purchase price of the engine block heater.
Details
On certain vehicles, the rear wheel suspension link arms could separate. This could result in loss of vehicle control and cause a crash resulting in injury and/or damage to property. Correction: Dealers will replace both suspension link arms and encase them in epoxy to prevent future improper servicing. Note: This recall supersedes recall 2013327. As part of the previous recall, dealers were to inspect the suspension arms for corrosion, replace them depending on their condition, and encase them in epoxy. Only vehicles which did not receive replacement of both suspension arms through the previous recall will need to be repaired under this campaign.
Details
On certain vehicles, in the event of a severe frontal collision, there is a possibility that the webbing of the seat belt in both second-row outboard seating positions could contact a portion of the metal seat cushion frame, become cut, and separate. If this occurs, the seat belt may not properly restrain the occupant, which could increase the risk of injury. Correction: Dealers will install plastic protectors on the seat cushion frame in both second-row outboard seating positions.
Details
On certain vehicles, inconsistent application of grease during the manufacturing process could cause the driver's side power window master switch to stick or become inoperative due to electrical contact point wear. This could cause debris to accumulate between the contact points, potentially resulting in an electrical short circuit. If a short circuit occurs, the switch assembly may overheat, produce smoke, melt and/or potentially lead to a fire causing injury and/or property damage. Correction: Dealers will inspect the driver's power window master switch and apply a specialized grease that inhibits heat build-up, or replace the power window master switch circuit board, as necessary. Note: This is an expansion of recall 2012-338.
Details
On certain vehicles equipped with a water channel located underneath the cowl louver at the base of the windshield and above the windshield wiper link assembly, due to stresses applied to the water channel during the manufacturing process, a section of the channel in some vehicles may become deformed and prevent water from draining properly. If water were to collect in the channel, it may drip onto the joint that connects the windshield wiper link and wiper motor. Over time, water dripping on this joint could result in corrosion and/or wear to the joint, which could result in the separation of the wiper link from the wiper motor crank arm. If separation were to occur, the windshield wipers could become inoperative, which could limit the driver’s visibility under certain operating conditions which may increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will replace the water channel, the wiper link and wiper motor crank arm with ones of an improved design.
Details
On some vehicles, if the rear wheel alignment toe adjustment locking nuts are improperly tightened when an alignment is performed in the field, backlash may develop in the threaded portion of the suspension arm (shaft and turnbuckle), followed by the formation of rust. If this occurs, threads may wear, causing the arm to separate which could result in loss of vehicle control. Correction: Dealers will inspect the suspension arm threads for corrosion. If corrosion is found, the arm(s) will be replaced. If no corrosion is found, an epoxy sealer will be applied to the suspension arm to inhibit corrosion. Note: This recall supersedes recall 2012253. Vehicles that were repaired under the previous campaign will also need to be repaired under this campaign.
Details
On certain vehicles, due to improperly applied grease, the driver's side power window master switch could stick or become inoperative. If attempts are made to lubricate the switch, the switch assembly could overheat and melt. A melting switch may produce smoke and potentially lead to a fire causing property damage and/or personal injury. Correction: Dealers will inspect the driver's power window master switch and apply a specialized grease that inhibits heat build-up, or replace the power window master switch circuit board, as necessary.
Details
This recall was replaced by Transport Canada recall no. 2013-327. On some vehicles, if the rear wheel alignment toe adjustment locking nuts are improperly tightened when an alignment is performed in the field, backlash may develop in the threaded portion of the suspension arm (shaft and turnbuckle), followed by the formation of rust. If this occurs, threads may wear, causing the arm to separate which could result in loss of vehicle control. Correction: Dealers will inspect the arms and verify the tightening torque of the lock nuts, or replace the arms, as necessary.
Details
On certain vehicles, the accelerator pedal may become stuck in the wide open position due to an unsecured or incompatible driver's floor mat. A fully depressed accelerator pedal may result in very high vehicle speeds and make it difficult to slow or stop the vehicle. This could result in a crash causing property damage and/or personal injury. Correction: Dealers will modify or replace the accelerator pedal. Note: This is an expansion of recall 2009290 for vehicles not previously included in the campaign.
Details
On certain vehicles, accelerator pedal movement may become rough, slow to return, or the pedal may stick in a depressed position. This could result in a loss of throttle control and a vehicle crash, causing property damage, personal injury or death. Correction: Dealers will install a steel reinforcement bar to the accelerator pedal assembly. With this reinforcement in place, the excess friction that can cause the pedal to stick is eliminated.
Translated automatically from the RDW's Dutch text. The original is at the source.
It may not apply to vehicles sold in your country. Check with your VIN at the source.
Consequence · Remedy
The 3-point seatbelt comes into contact with the frame of the rear seat. This could damage the seatbelt during a frontal collision. The belt may tear. If this occurs, the seatbelt will no longer keep the occupant in place, increasing the risk of injury.
The manufacturer is recalling the affected vehicles. Measures will be taken to rectify the defect. The vehicle owner is requested to make an appointment with the brand dealer. They will apply protection to the rear seat frame.
Consequence · Remedy
In the main switch of the electric window control mounted on the inside of the driver's door, wear may occur due to poor lubrication. As a result of wear and moisture, a short circuit may occur. This can cause the main switch to overheat and melt. A smoldering switch may produce smoke and possibly lead to a fire.
The manufacturer is recalling the affected vehicles. Measures will be taken to rectify the defect. The vehicle owner is requested to make an appointment with a brand dealer. They will check the window control switch. The switch will be lubricated with new grease and the circuit board will be replaced if necessary.
Consequence · Remedy
There is a possibility that a signal cable of the driver's airbag may be damaged due to its shape and location through internal contact as a result of the steering wheel turning. The driver's airbag may then possibly fail to work. The airbag warning light will illuminate in that case.
The manufacturer is recalling the affected vehicles. Measures will be taken to fix the defect. The vehicle owner is requested to make an appointment with a brand dealer. The signal cable for the driver's airbag will then be replaced.
Consequence · Remedy
The rear control arms may corrode if the rear wheel alignment was readjusted during a workshop visit and the specifications for tightening the nuts were not followed correctly. Play in the rear control arm can lead to loss of control over the vehicle.
The manufacturer/distributor is recalling the affected vehicles/products and will take measures to rectify the defect. The vehicle owner is requested to make an appointment with the brand dealer or an authorized repairer. They will check the rear control arms and replace them if necessary.
On the road
Cars of this model first registered in 2009, from official registers. Each figure belongs to its country.
🇳🇱 Vehicle register, Netherlands
831 still registered
5% with an open recall
Average list price when new: 33,165 € (Dutch taxes included) · RDW, CC0
Common problems
327 reports🇺🇸 Local dataReported by owners to the source below. It is not a verdict on this car: it is what people wrote.
We were informed of safety recalls for our Toyota Rav 4 2009 . We called the local Toyaota dealership for the recalls and was told on the phone after we dropped it off that they did the inspection to make sure the recalls could be completed and informed us that they could ,but they needed to keep overnight because the…
I am writing to report a suspected case of odometer fraud involving a vehicle currently listed for sale at Stacey’s Auto Sales, located at [XXX] . Vehicle Details: 2009 Toyota RAV4 Sport VIN: [XXX] Asking Price: $8,995 Current Listed Mileage: 108,540 I obtained an NMVTIS vehicle history report which shows this vehicl…
Repairs of the control arms indicated on recall NHTSA 16V-596 were never done on my vehicle after the recall was issued in 2016. Smart motors Toyota in Madison confirmed that the replacement of the control arms was never done on my vehicle, but they are showing no open recalls on my vehicle in their system due to this…
The contact owns a 2009 Toyota Rav4. The contact stated that there was an abnormal grinding sound coming from the engine at startup. There was no warning light illuminated. The vehicle was taken to an independent mechanic, and the contact was informed that the engine was consuming an excessive amount of engine oil cau…
Engine timeing system rattle on startup. Even basic web research shows this is a common problem for select model years and acorss mulitple models. This issue has a high probility of causing catastrophic engine damage, where the timeing chain & VVT system fails to keep timing causing the valves to colide with the pis…
I was hit with a rock right between my eyes while driving, took Toyota into shop they were surprised it had not fell in on my lap. Window frame has corroded, glass shop said the manufacturer did not paint were the seals meet around the window and has allowed moisture in and corroded the frame. I have 160,000 miles on …
We have a 09 Toyota Rav4 with a Blizzard Pearl paint that continues to fail. Apparently there were notices sent out in 2022 indicating a recall that would cover these repairs. We were unaware of these notices and continue to experience paint degradation on multiple areas of the car. I have contacted Toyota and they c…
My son was looking to get his new tires aligned, and was informed by the mechanic that he would need to replace both side rear lower control arms, as Toyota had performed a safety recall GOV, resulting in the arms being epoxied, and therefore cannot be adjusted/ aligned. I contacted Toyota customer experience center…
Four incidents of unintended acceleration , in all instances foot was on break petal NOT on gas petal, 3 instances vehicle was stopped at traffic light, last incident was pulling into a parking space foot on brake, in all instances braked hard and shifted vehicle into neutral and turned vehicle off to avoid collisions…
My rear passenger suspension has multiple part damage. Rear shock bracket failure and other parts.
paint recall the problem was confirmed twice by sansone dealership avenel, nj. 4/28/2021 and 12/1/2022. on both occasionspictures were submitted and i was told it would be taken care of. on 1/23/2023 i dropped car off to be repainted and was told it would be about 1.5 weeks. i picked up the car unrepaired on 2/21/20…
Engine rattle on cold start ups.
2009 vs. other RAV4 years
🇺🇸 Local dataOwner complaints and recall campaigns on record at NHTSA for each model year. Fewer complaints can also mean fewer cars sold or a newer car.
Questions
- What engine does the 2009 Toyota RAV4 have?
- The 2009 Toyota RAV4 came with 2 engines: 2.5 L 4-cylinder, 3.5 L 6-cylinder.
- What is the fuel economy of the 2009 Toyota RAV4?
- It gets 21 to 24 MPG combined depending on the engine, per the EPA.
- Does the 2009 Toyota RAV4 have recalls?
- 15 recall campaigns are on record. The latest concerns Suspension (2016-08-12).
- What are the common problems of the 2009 Toyota RAV4?
- 327 owners have filed complaints, most often about vehicle speed control.
Other years
Other models by Toyota
Do you own a 2009 RAV4?
Post it for free and reach buyers who are already looking at this exact car.
- Free, with no commission
- About three minutes
- Your listing shows up on this page