2007 Toyota RAV4
The 2007 Toyota RAV4 came with 2 engines: 2.4 L 4-cylinder, 3.5 L 6-cylinder. It gets 21 to 23 MPG combined depending on the engine, per the EPA. ANCAP rates it 4 out of 5 stars. 14 recall campaigns and 1,003 owner complaints are on record.
Specs
| Cylinders | 4 |
|---|---|
| Transmission | Automatic · 4 speeds |
| Drivetrain | AWD |
| Length | 183 mm (7.2 in) |
| Width | 426 mm |
| Curb weight | 1,463 kg (3,225 lb) |
| Seats | 5 |
| Body style | Sport Utility Vehicle - 2WD |
Specs: average of the cars of this model first registered in 2007 in the Netherlands (RDW vehicle register).
For sale in United States
Safety
Crash-test results across markets. They can vary by version and equipment.
Fuel economy (MPG)
🇺🇸 Local dataBy version
| Engine | Transmission | Drivetrain | City | Highway | Combined |
|---|---|---|---|---|---|
| 2.4 L 4-cylinder | Automatic · 4 speeds | AWD | 20 MPG | 25 MPG | 22 MPG |
| 2.4 L 4-cylinder | Automatic · 4 speeds | Front-wheel (FWD) | 21 MPG | 27 MPG | 23 MPG |
| 3.5 L 6-cylinder | Automatic · 5 speeds | AWD | 19 MPG | 26 MPG | 21 MPG |
| 3.5 L 6-cylinder | Automatic · 5 speeds | Front-wheel (FWD) | 19 MPG | 27 MPG | 22 MPG |
EPA figures for each version sold in the U.S.
Recalls
Consequence · Remedy
Failure of the rear tie rod could cause a loss of vehicle control, increasing the risk of a crash.
Toyota will notify owners and dealers will replace both rear suspension arms and encapsulate the locknuts, free of charge. The recall began on September 30, 2016. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's numbers for this recall are G0V for Toyota vehicles and GLK for Lexus vehicles. Note: This recall supersedes recall 13V-383, in which some vehicles were only inspected, sealed, and did not have both arms replaced. The affected vehicles were previously recalled under 13V-383, but did not have both rear suspension arms replaced at that time. Those vehicles need to have both arms replaced as part of this recall remedy.
Consequence · Remedy
If damaged, the copper strand heating element may short circuit, increasing the risk of a fire.
SET will notify owners, and dealers will disconnect the seat heaters, free of charge, and refund the purchase price of the seat heater accessory. The recall began on July 14, 2016. Owners may contact SET customer service at 1-866-405-4226. SET number for this recall is SET16B.
Consequence · Remedy
A cut seat belt may not properly restrain the seat occupant, increasing their risk of injury in a crash.
Toyota will notify owners, and dealers will install a protector over both rear seat cushion frames, free of charge. The recall began on June 24, 2016. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is G0F.
Consequence · Remedy
If the sliding electrical contacts are not protected by lubricant, debris and moisture that get into the switch may cause a short circuit and the switch assembly may overheat and melt, increasing the risk of a fire.
Toyota will notify owners, and dealers will inspect the switch, applying a lubricant if no abnormality is found. If abnormality is found, the PWMS circuit board will be replaced, free of charge. The recall is expected to begin December 20, 2015. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is C0M.
Consequence · Remedy
Damage to the seat heater wiring could cause the wires to short, increasing the risk of the seat burning and causing personal injury to the occupant.
SET will notify owners, and dealers will disconnect the heaters with copper strand heating elements and refund the purchase price of the seat heater accessory, free of charge. The recall is expected to began in January 2015. Owners may contact SET customer service at 1-866-405-4226.
Consequence · Remedy
If the FFC is damaged, connectivity to the driver's air bag module could be lost and the air bag deactivated. The failure of the driver's air bag to deploy in the event of a crash that typically necessitates deployment increases the risk of injury to the driver.
Toyota will notify the Toyota vehicle owners, and General Motors will notify the Pontiac Vibe owners. Toyota sent owners an interim notification letter in May 2014 to advise owners of the recall. Toyota will mail owners a second letter when remedy parts are available. General Motors sent Pontiac Vibe owners an Interim letter on June 20, 2014 notifying them that parts are currently unavailable. General Motors sent notices to the Pontiac Vibe owners on September 15, 2014, that a remedy is available. The recall began on October 27, 2014. Owners may contact Toyota at 1-800-331-4331. Owners may contact General Motors at 1-800-762-2737.
Consequence · Remedy
Failure of the rear tie rod could cause a loss of vehicle control, increasing the risk of a crash.
Toyota will notify owners, and dealers will inspect the tie rods and replace any that have rust or corrosion on the alignment adjustment threads. All of the rear tie rods will then be encased in an epoxy to prevent future environmental damage. Due to limitations in parts, the recall remedy will be launched in phases from September 2013 through mid-April 2014. All owners will receive notification of the recall, with most receiving second notifications when parts are available in their area. IMPORTANT: This recall supersedes Toyota and Lexus recall 12V-373. All vehicles that have been inspected and remedied under the previous recall need to be re-inspected and have the appropriate remedy applied.
Consequence · Remedy
If the switch overheats, it may melt, possibly resulting in a fire.
Toyota will notify its owners, and dealers will inspect the switch and apply a special grease that inhibits heat build up or replace any switch damaged by the defect, free of charge. Toyota owners that experience a problem with a switch should not attempt to make repairs, but should contact their Toyota dealer or the Toyota Customer Experience Center at 1-800-331-4331. General Motors will contact the Pontiac Vibe owners affected by this recall and GM dealers will inspect and repair switches as necessary. Those owners may contact Pontiac Customer Care at 1-800-762-2737.
Consequence · Remedy
Failure of the rear tie rod could cause a loss of vehicle control, increasing the risk of a crash.
Toyota will notify owners, and dealers will inspect the rear tie-rod nut for looseness and replace any suspect tie-rod found loose. Dealers will also affix instructions in multiple places to prevent improper servicing in the future. The recall began on November 30, 2012. Owners may contact Toyota at 1-800-331-4331 or Lexus at 1-800-255-3987.
Consequence · Remedy
INADVERTENT ACTIVATION OF THE CSA AND/OR THE SEAT BELT PRETENSIONER CAN CAUSE INJURY TO A VEHICLE OCCUPANT.
TOYOTA WILL REPLACE THE AIRBAG SENSOR ASSEMBLY WITH A NEW ONE CONTAINING IMPROVED ROLL RATE SENSORS, FREE OF CHARGE. TOYOTA INTENDS TO SEND AN INTERIM OWNER NOTIFICATION TO OWNERS EARLY TO MID-MAY, 2011 WHEN SUFFICIENT PARTS AND REMEDY BECOMES AVAILABLE. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
Consequence · Remedy
A STUCK OPEN ACCELERATOR PEDAL MAY RESULT IN VERY HIGH VEHICLE SPEEDS AND MAKE IT DIFFICULT TO STOP THE VEHICLE, WHICH COULD CAUSE A CRASH, SERIOUS INJURY OR DEATH.
THE REMEDY IS NOW AVAILABLE. THE SAFETY RECALL BEGAN EARLY APRIL 2011. THE REMEDY WILL INVOLVE MODIFICATION OR REPLACEMENT OF THE ACCELERATOR PEDAL AND REPLACEMENT OF ANY TOYOTA ALL-WEATHER FLOOR MAT. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331 OR LEXUS AT 1-800-255-3987.
Consequence · Remedy
THIS DOES NOT MEET THE STANDARD REQUIREMENTS.
DEALERS WILL MAIL TO CONSUMERS THE CORRECTED LABEL OR THE CUSTOMER WILL HAVE THE OPTION FOR DEALERS TO INSTALL THE LABEL FREE OF CHARGE. DEALERS WILL ALSO CORRECT THE OWNER'S MANUAL. THE SAFETY RECALL BEGAN ON MAY 27, 2010. OWNERS MAY CONTACT GULF STATES TOYOTA AT 713-580-3300.
Consequence · Remedy
A DRIVER MAY OVERLOAD A VEHICLE WHICH MAY INCREASE THE RISK OF A CRASH.
DEALERS WILL MAIL TO CONSUMERS THE CORRECTED LABEL OR THE CUSTOMER WILL HAVE THE OPTION FOR DEALERS TO INSTALL THE LABEL FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 27, 2010. OWNERS MAY CONTACT SOUTHEAST TOYOTA AT 1-800-301-6859.
Consequence · Remedy
INCORRECT LOAD CARRYING CAPACITY MODIFICATION LABELS COULD RESULT IN THE VEHICLE BEING OVERLOADED, INCREASING THE RISK OF A CRASH.
TOYOTA WILL NOTIFY OWNERS AND PROVIDE THEM WITH A NEW, ACCURATE LABEL TO BE INSTALLED OVER THE INACCURATE LABEL FREE OF CHARGE. THE SAFETY RECALL BEGAN ON AUGUST 18, 2009. OWNERS MAY CONTACT TOYOTA AT 1-888-270-9371.
It may not apply to vehicles sold in your country. Check with your VIN at the source.
Details
Issue: This recall is for certain block heater kits installed on certain vehicles or sold as accessories at Toyota or Lexus dealerships. On certain vehicles, the engine block heater cable may not have enough heat protection and could be damaged by high temperatures. If this happens, the cable could short circuit while plugged in, and cause the wiring to overheat or melt. Note: This recall only affects the following block heater/cord part numbers: C014003034 PK5A408J09 PU14000904 C014003151 PK5A408J13 PU14000905 C014000885 PK5A489J11 PU14000907 C014000888 PK5A489J22 PU14000909 C014000907 PK5A410H00 PU14000911 C014100904 PU14000900 PU14000913 C014100907 PU14000901 PU14003571 C014100911 PU14000902 PK5A489J14 PK5A408J05 PU14000903 Safety Risk: Engine block heater wiring that overheats or melts could create the risk of a fire. Corrective Actions: Toyota recommends that you should stop using the engine block heater immediately. Toyota will notify owners by mail and instruct you to take your vehicle to a dealer to disable the engine block heater. For some vehicles, the corrective actions for this recall are under development. For others, a new engine block heater cannot be installed, and the owner will receive a refund of the purchase price of the engine block heater.
Details
On certain vehicles, the rear wheel suspension link arms could separate. This could result in loss of vehicle control and cause a crash resulting in injury and/or damage to property. Correction: Dealers will replace both suspension link arms and encase them in epoxy to prevent future improper servicing. Note: This recall supersedes recall 2013327. As part of the previous recall, dealers were to inspect the suspension arms for corrosion, replace them depending on their condition, and encase them in epoxy. Only vehicles which did not receive replacement of both suspension arms through the previous recall will need to be repaired under this campaign.
Details
On certain vehicles, in the event of a severe frontal collision, there is a possibility that the webbing of the seat belt in both second-row outboard seating positions could contact a portion of the metal seat cushion frame, become cut, and separate. If this occurs, the seat belt may not properly restrain the occupant, which could increase the risk of injury. Correction: Dealers will install plastic protectors on the seat cushion frame in both second-row outboard seating positions.
Details
On certain vehicles, inconsistent application of grease during the manufacturing process could cause the driver's side power window master switch to stick or become inoperative due to electrical contact point wear. This could cause debris to accumulate between the contact points, potentially resulting in an electrical short circuit. If a short circuit occurs, the switch assembly may overheat, produce smoke, melt and/or potentially lead to a fire causing injury and/or property damage. Correction: Dealers will inspect the driver's power window master switch and apply a specialized grease that inhibits heat build-up, or replace the power window master switch circuit board, as necessary. Note: This is an expansion of recall 2012-338.
Details
On certain vehicles, electrical circuitry in the steering wheel assembly may become damaged. As a result, the driver's airbag may not function as intended, causing the instrument panel airbag warning lamp to illuminate. Failure of the driver's airbag to deploy during a crash (where deployment is warranted) could increase the risk of injury to the seat occupant. Correction: Dealers will replace the spiral cable assembly.
Details
On some vehicles, if the rear wheel alignment toe adjustment locking nuts are improperly tightened when an alignment is performed in the field, backlash may develop in the threaded portion of the suspension arm (shaft and turnbuckle), followed by the formation of rust. If this occurs, threads may wear, causing the arm to separate which could result in loss of vehicle control. Correction: Dealers will inspect the suspension arm threads for corrosion. If corrosion is found, the arm(s) will be replaced. If no corrosion is found, an epoxy sealer will be applied to the suspension arm to inhibit corrosion. Note: This recall supersedes recall 2012253. Vehicles that were repaired under the previous campaign will also need to be repaired under this campaign.
Details
On certain vehicles, due to improperly applied grease, the driver's side power window master switch could stick or become inoperative. If attempts are made to lubricate the switch, the switch assembly could overheat and melt. A melting switch may produce smoke and potentially lead to a fire causing property damage and/or personal injury. Correction: Dealers will inspect the driver's power window master switch and apply a specialized grease that inhibits heat build-up, or replace the power window master switch circuit board, as necessary.
Details
This recall was replaced by Transport Canada recall no. 2013-327. On some vehicles, if the rear wheel alignment toe adjustment locking nuts are improperly tightened when an alignment is performed in the field, backlash may develop in the threaded portion of the suspension arm (shaft and turnbuckle), followed by the formation of rust. If this occurs, threads may wear, causing the arm to separate which could result in loss of vehicle control. Correction: Dealers will inspect the arms and verify the tightening torque of the lock nuts, or replace the arms, as necessary.
Details
On certain vehicles, the roll angle sensors in the airbag sensor assembly could fail. If one of the roll angle sensors malfunctions, the airbag warning lamp will illuminate, the roll detection system will be suspended, and the curtain shield airbag will not deploy during a roll-over crash (where deployment is warranted), thereby increasing the risk of personal injuries to the seat occupant. The airbag system, however, will continue to detect frontal and lateral impacts and, in those instances, will function as designed. If both roll angle sensors fail nearly simultaneously after starting the vehicle, the curtain shield airbag and the seatbelt pretensioner could inadvertently deploy. Inadvertent curtain shield airbag deployment in a non-impact situation may cause damage to the surrounding vehicle environment and create expensive vehicle repair, including replacement of the curtain shield airbag module and the airbag electronic control unit. In some instances, inadvertent deployment could cause minor injuries to vehicle occupants. Correction: Dealers will replace the airbag sensor assembly.
Details
On certain vehicles, the accelerator pedal may become stuck in the wide open position due to an unsecured or incompatible driver's floor mat. A fully depressed accelerator pedal may result in very high vehicle speeds and make it difficult to slow or stop the vehicle. This could result in a crash causing property damage and/or personal injury. Correction: Dealers will modify or replace the accelerator pedal. Note: This is an expansion of recall 2009290 for vehicles not previously included in the campaign.
Translated automatically from the RDW's Dutch text. The original is at the source.
It may not apply to vehicles sold in your country. Check with your VIN at the source.
Consequence · Remedy
The 3-point seatbelt comes into contact with the frame of the rear seat. This could damage the seatbelt during a frontal collision. The belt may tear. If this occurs, the seatbelt will no longer keep the occupant in place, increasing the risk of injury.
The manufacturer is recalling the affected vehicles. Measures will be taken to rectify the defect. The vehicle owner is requested to make an appointment with the brand dealer. They will apply protection to the rear seat frame.
Consequence · Remedy
There is a possibility that a signal cable of the driver's airbag may be damaged due to its shape and location through internal contact as a result of the steering wheel turning. The driver's airbag may then possibly fail to work. The airbag warning light will illuminate in that case.
The manufacturer is recalling the affected vehicles. Measures will be taken to fix the defect. The vehicle owner is requested to make an appointment with a brand dealer. The signal cable for the driver's airbag will then be replaced.
Consequence · Remedy
The rear control arms may corrode if the rear wheel alignment was readjusted during a workshop visit and the specifications for tightening the nuts were not followed correctly. Play in the rear control arm can lead to loss of control over the vehicle.
The manufacturer/distributor is recalling the affected vehicles/products and will take measures to rectify the defect. The vehicle owner is requested to make an appointment with the brand dealer or an authorized repairer. They will check the rear control arms and replace them if necessary.
Consequence · Remedy
In the driver's door, there is a master switch for operating the electrically powered windows. The switches in this master switch are insufficiently lubricated. These switches may get stuck and not function properly, and in exceptional cases, the switch may heat up and melt.
The vehicle owner is requested to make an appointment with the brand dealer. They will check the functionality of the switches. If it is found that the switches are functioning roughly, they will be replaced. If the switches are functioning smoothly, they will be treated with special grease.
On the road
Cars of this model first registered in 2007, from official registers. Each figure belongs to its country.
🇳🇱 Vehicle register, Netherlands
1,211 still registered
6% with an open recall
Average list price when new: 36,903 € (Dutch taxes included) · RDW, CC0
Common problems
1003 reports🇺🇸 Local dataReported by owners to the source below. It is not a verdict on this car: it is what people wrote.
This vehicle never got a incident, l don’t know why l got this recall
UNKNOWN
My driver side door caught on fire and was completely destroyed to include all associated wiring. Toyota had my contact information but never contacted me about any of the recalls.
The contact owns a 2007 Toyota Rav4. The contact stated that the vehicle could not be aligned. There were no warning lights illuminated. The vehicle was previously taken to the local dealer to be repaired under NHTSA Campaign Number: 16V596000 (Suspension). The vehicle was taken to a tire shop, and the contact was inf…
Other people keep using my Bluetooth from my Toyota RAV4 2007. I don't even use it anymore. I found out because my android vehicle app keeps activating. Also, I live in a apartment complex, and notice when I look out my window, people walk by and slow down and stop right in front of my car and start messing with their…
Sub frame is rusted to the point of not being able to pass state inspection requirements.
Unknown I just strongly feel like I'm not getting the information on purpose..it has caused me much stress. I'm really upset. I've not once received any communication from you since I bought this vehicle 2nd hand. In 2018.. And to make matters worse, I've had my vehicle plates stolen 3 separate times including my ce…
The contact owns a 2007 Toyota Rav4. The contact stated while driving 40 MPH, the steering wheel seized. The contact was able to regain control of the vehicle. There were no warning lights illuminated. The vehicle was taken to an independent mechanic. The local dealer was not contacted. The vehicle was not yet diagnos…
The contact owns a 2007 Toyota Rav4. The contact stated while driving at an undisclosed speed, the vehicle lost motive power. There was no warning light illuminated. The vehicle was able to be restarted. The vehicle was taken to an independent mechanic where it was diagnosed with battery failure. The contact was infor…
The contact owns a 2007 Toyota Rav4. The contact stated while driving at various speeds, there was an abnormally loud sound coming from underneath the vehicle. The vehicle was taken to an independent mechanic, where the contact was informed that the sound was coming from the tires. The contact was informed that no iss…
Subframe rusted in half, the only way I found it was when we put new shocks on it. It peeled off about 1/2 the tread on a brand new tire. Dangerous, if passengers side rear tire would've broke loose it would throw rear of car into oncoming traffic!
I own a 2007 Toyota Rav-4 with 155k miles. I had bought the vehicle used from a licensed Toyota dealership about 3 years ago and have been diligent about conducting the routine scheduled maintenance. The vehicle had no known recalls. I was driving about 25mph when I started to smell smoke. The drivers side door caug…
2007 vs. other RAV4 years
🇺🇸 Local dataOwner complaints and recall campaigns on record at NHTSA for each model year. Fewer complaints can also mean fewer cars sold or a newer car.
Questions
- What engine does the 2007 Toyota RAV4 have?
- The 2007 Toyota RAV4 came with 2 engines: 2.4 L 4-cylinder, 3.5 L 6-cylinder.
- What is the fuel economy of the 2007 Toyota RAV4?
- It gets 21 to 23 MPG combined depending on the engine, per the EPA.
- Is the 2007 Toyota RAV4 safe?
- ANCAP rates it 4 out of 5 stars.
- Does the 2007 Toyota RAV4 have recalls?
- 14 recall campaigns are on record. The latest concerns Suspension (2016-08-12).
- What are the common problems of the 2007 Toyota RAV4?
- 1,003 owners have filed complaints, most often about steering.
Other years
Other models by Toyota
Do you own a 2007 RAV4?
Post it for free and reach buyers who are already looking at this exact car.
- Free, with no commission
- About three minutes
- Your listing shows up on this page