BMW X5 2000

An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.

Owners are advised not to drive their vehicles until the remedy is complete. Dealers will inspect and replace the driver's front air bag, as necessary, free of charge. Owner notification letters were mailed December 29, 2025. Owners may contact BMW customer service at 1-800-525-7417. Vehicle Identification Numbers (VINs) involved in this recall will be searchable on NHTSA.gov beginning December 23, 2025. This recall expands previous NHTSA recall number 19V015.

THIS COULD INITIALLY CAUSE SOME BRAKE FLUID LEAKAGE, AND EVENTUALLY LEAD TO A SUBSTANTIAL LOSS OF BRAKE FLUID. THERE COULD BE A NOTICEABLE REDUCTION IN BRAKE PERFORMANCE IF A LOSS OF FRONT BRAKE PERFORMANCE OCCURS.

DEALERS WILL INSTALL AN ADDITIONAL RETAINING CLIP TO FURTHER SECURE THE BRAKE LINE TO THE FRONT STRUT. ADDITIONALLY, IF INSPECTION OF ANY BRAKE HOSE INDICATES THAT IT HAS EXPERIENCED DAMAGE, THE HOSE WILL BE REPLACED. OWNER NOTIFICATION BEGAN FEBRUARY 14, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT BMW AT 1-800-831-1117.

EVENTUALLY, THE BRAKE PEDAL ARM COULD DETACH FROM THE BRACKET, RENDERING THE SERVICE BRAKING SYSTEM INEFFECTIVE, INCREASING THE RISK OF A CRASH.

DEALERS WILL CHECK THE BRAKE PEDAL ARM PIVOT SHAFT FOR PROPER SEATING IN ITS SUPPORT BRACKET. IN ADDITION, A PIN WILL BE INSTALLED TO SECURE THE SHAFT TO THE BRACKET. OWNER NOTIFICATION BEGAN AUGUST 14, 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT BMW AT 1-800-332-4269.

CONTINUED CHAFFING CAN CAUSE THE ANTICORROSION COATING OF THIS BRAKE LINE TO FAIL, ALLOWING THE BRAKE LINE TO RUST THROUGH AND LEADING TO LOSS OF BRAKE FLUID, FAILURE OF THE REAR BRAKE CIRCUIT, AND EXTENDED STOPPING DISTANCES, AND A POSSIBLE CRASH.

DEALERS WILL INSTALL A RUBBER SPACER BELOW THE PLASTIC CARRIER TO PREVENT SAGGING AND SUBSEQUENT CONTACT BETWEEN THE OIL AND BRAKE LINES. BRAKE LINES WHOSE ANTICORROSION LAYER IS FOUND TO BE DAMAGED AS A RESULT OF CONTACT WITH THE OIL LINE WILL BE REPLACED. OWNER NOTIFICATION BEGAN AUGUST 14, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT BMW AT 1-800-831-1117.

IF THIS PROBLEM OCCURS, THE ABILITY TO MAINTAIN SPEED IN TRAFFIC AND/OR ACCELERATE COULD BE GREATLY DIMINISHED, POSSIBLY LEADING TO A CRASH.

DEALERS WILL REPLACE THE TRANSMISSION GEAR POSITION INDICATOR SWITCH. OWNER NOTIFICATION BEGAN AUGUST 14, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT BMW AT 1-800-831-1117.

OPERATION OF THE VEHICLE, ESPECIALLY IN ROUGH ROAD CONDITIONS, CAN CAUSE THE CLEARANCE BETWEEN THE COLLAR AND THE STEERING RACK TO INCREASE TO THE POINT WHERE THE INPUT SHAFT CAN SEPARATE FROM THE RACK, RESULTING IN A LOSS OF STEERING CAPABILITY.

DEALERS WILL INSPECT THE STEERING RACK INPUT SHAFT COLLAR FOR PROPER POSITIONING, AND REPOSITION IS NECESSARY.

Issue: This recall applies to vehicles that may be equipped with a replacement sport steering wheel that has a Takata airbag. Long-term exposure to high absolute humidity and temperature, combined with high temperature cycling, may eventually degrade the propellant contained in the driver-front airbag. This could cause the airbag to deploy with more force than normal. If the airbag inflator ruptures, fragments could be propelled toward vehicle occupants or cause damage to the airbag assembly, preventing its proper function. Safety Risk: If the vehicle is involved in a crash requiring an airbag deployment, the airbag inflator could rupture and create a risk of injury. Corrective Actions: To reduce the safety risk, BMW advises you not to drive the vehicle until the recall repairs have been completed. BMW will notify owners by mail and advise you to contact a dealership to arrange for an inspection and, if necessary, replacement of the driver-front airbag module. To learn if your vehicle is affected by this recall, owners may: • Visit <a href= https://www.bmw.ca/en/ssl/VehicleRecall.html> https://www.bmw.ca/en/ssl/VehicleRecall.html</a> • Contact your preferred or local BMW Retailer • Call BMW Customer Relations Recall Services at 1-855-217-3002

Certain vehicles fail to conform to Canada Motor Vehicle Safety Standards. Specifically, the compliance label does not indicate the wheel rim size, as required by the Standard. Correction: Due to the inconsequential nature of this non-compliance, no action will be taken.

On certain vehicles, the grommet holding the brake line to the front struts may slip out of its bracket. Consequently, the brake hose attached to the brake line may come in contact with the tire and be subject to wear and abrasion. This could cause some brake fluid leakage which would eventually illuminate the brake warning indicator light. If a loss of front brake performance occurs, the rear brake circuit will still be functional, and will be able to slow and stop the vehicle. Correction: Dealer will install an additional retaining clip in order to further secure the line and grommet to the strut.

On certain passenger vehicles the brake pedal arm pivot shaft could loosen from its support bracket. Eventually, the brake pedal arm could detach from the bracket, rendering the braking system ineffective, increasing the risk of a crash. Correction: Dealers will check the brake pedal arm pivot shaft for proper seating in its support bracket. In addition, a pin will be installed to secure the shaft to the bracket.

On certain vehicles, the plastic collar which fits over the lower steering rack input shaft may not have been pushed down fully onto the rack at the assembly plant. As a result, there can be substantially more clearance between the steering rack and the collar than the design clearance. This could eventually result in the input shaft separating from the rack with subsequent loss of steering capability. Correction: Steering rack input shaft collar will be inspected for proper positioning and repositioned if necessary.

Due to aging effects in the gas generator of the driver's airbag, a too high pressure can occur during activation. The internal pressure in the gas generator may become too high during activation. The gas generator can explode and metal parts may cause injury, possibly fatal injuries under certain conditions.

The vehicle owner is invited to make an appointment with the brand dealer. They will replace the airbag module.