MINI Cooper 2007 — Problemas reportados

I recently purchased a used MINI Cooper with incomplete NHTSA Safety Recall 23V-337 involving the Footwell Control Module (FRM). The previous owner did not complete the recall remedy. The vehicle's turn signals and brake lights are currently inoperative. The FRM controls various vehicle lighting functions and is the component involved in Recall 23V-337. Because I purchased the vehicle with these conditions already present, I do not know what warning lamps, messages, or symptoms occurred before the failures. The loss of both turn signals and brake lights creates a significant safety risk because other motorists cannot be properly notified when the vehicle is turning, changing lanes, slowing, or stopping. Additionally, Recall 23V-337 states that corrosion of the FRM can potentially result in a short circuit and, in rare cases, a thermal event that could increase the risk of injury. The vehicle has not yet been inspected to determine whether the current lighting failures are directly caused by the recalled FRM, but the recall remains incomplete and the vehicle is available for inspection. I contacted BMW/MINI seeking completion of the recall. I was informed that it must be performed by an authorized MINI dealer. There is no authorized MINI dealer in Montana, and the nearest facility is approximately 500 miles away. BMW/MINI declined transportation assistance, mobile repair, or authorization for a closer BMW dealer or qualified repair facility. Although the vehicle can move under its own power, driving approximately 500 miles without brake lights or turn signals, while it also has an outstanding recall involving a potential electrical short circuit and thermal event, presents a serious safety concern. I am actively attempting to complete the recall and am requesting NHTSA review the safety issue and BMW/MINI's lack of a practical means for safely accessing the recall remedy.

What happened: Vehicle has experienced failure of the Footwell Control Module (FRM) and associated wiring harness in the driver footwell area, consistent with NHTSA Recall 23V-337. Symptoms: • Exterior lights (headlights / taillights) remain illuminated far longer than normal after vehicle shutoff, sometimes not turning off at all. • Inspection revealed melted wiring, melted connector plugs and receptacles for headlight/taillight circuits. • Water was found in driver side footwell in the past / under carpet padding. Carpet pad is saturated. This is the same failure mode described in Recall 23V-337: "Due to a number of contributing factors, over time, the FRM could become susceptible to corrosion. Eventually, the corrosion could potentially result in a short circuit, resulting in a potential thermal event which could increase the risk of a fire or injury." Safety risk: Melted wiring and connectors create short circuit and thermal event risk, including fire risk while vehicle is parked and unattended. Lights failing to shut off creates dead battery / loss of exterior lighting control. I am concerned about vehicle fire. My vehicle shows evidence of having caught fire at the headlight and receptacle point. Recall history: Vehicle is included in NHTSA Campaign 23V-337000 (MINI Recall 23V-337 - Footwell Module Moisture/Water Intrusion). I was told remedy is still being developed / parts unavailable, or that additional wiring harness damage beyond the FRM itself is not fully covered. Dealer has inspected the vehicle and has completely disregarded the recall, which was the reason why I brought it in and have quoted me customer pay estimates for repairs covered under the recall. I am filing this to document that Recall 23V-337 failure has resulted in melted wiring harness components beyond just the FRM module, and to request NHTSA evaluate whether the current recall remedy fully addresses wiring harness damage caused by prolonged FRM corrosion / lights staying on.

The authorized dealer performed a non-compliant remedy for Safety Recall 23V-337. The initial repair resulted in melted wires and a charred connector due to high resistance. The dealer's subsequent re-repair utilized an un-staggered cluster of approximately 8 inline crimp connectors in a single tight bundle.This directly violates BMW Factory Repair Standard ISTA/AIR 61 13, which explicitly mandates: 'Arrange individual interfaces in an offset manner when repairing multiple cables. The wiring harness thus does not become too thick at the repaired point.' By failing to offset the splices, the dealership created a thick, bunched thermal mass that traps heat and strains the circuits, leaving an active passenger cabin fire hazard intact. Delivery has been officially refused

The contact owns a 2007 Mini Cooper. The contact stated that while driving at an undisclosed speed, the engine seized. No warning lights were illuminated. The vehicle was towed to the residence. The contact, who was an independent mechanic, researched and diagnosed the failure with water damage to the junction box electronics. The manufacturer was made aware of the failure but provided no assistance. The contact referenced an unknown recall that had a similar failure description; however, the VIN was not under recall. The contact was advised to contact the NHTSA Hotline to report the failure. The failure mileage was approximately 116,000.

The contact owns a 2007 Mini Cooper S. The contact stated that water was entering the vehicle through the sunroof. The contact stated that the water was collecting inside the headliner and would overflow and leak down the driver’s and passenger’s side sun visors and into the electronics of the footwell. Additionally, the front driver’s and passenger’s seats, floorboards, and dashboard would become soaked from moisture. Due to the failure, the vehicle would fail to start or operate as needed. Upon investigation, the contact discovered NHTSA Campaign Number: 23V337000 (Electrical System); however, the VIN was not included in the recall. An independent mechanic was notified about the failure and the contact was advised to park the vehicle outside as the failure could cause the vehicle to catch on fire. The manufacturer was then notified of the failure and the contact was referred to the NHTSA Hotline to report the failure. The vehicle was not repaired. The failure mileage was approximately 140,000.

The airbag warning light randomly remains on. From what I understand this is a known issue as there has been previous recalls by Mini. This could potentially mean the airbag system is faulty and non-operational. Based on online searches, it seems like a lot of there problem are wiring problems though, bad connections. The previous recalls should be extended further, as there are other cars with the same problem, like mine.

The contact owns a 2007 Mini Cooper S. The contact received notification of NHTSA Campaign Number: 23V337000 (Electrical System); however, the part to do the recall repair was not yet available. The contact stated that while the vehicle was parked, the sunroof was inoperative. The contact waited for several minutes for the sunroof to return to normal operation. The "Passenger Air Bag Disabled" message was displayed on the instrument panel; however, the passenger’s seat was occupied. The infotainment system was unintentionally turned on while the vehicle was turned off. The check engine and low tire pressure warning light were intermittently illuminated. The failures occurred on several different occasions. The contact stated that there was no local dealer; a dealer was not contacted. The vehicle was not diagnosed or repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. Parts distribution disconnect.

On almost all r56 model mini coopers the passenger seat occupancy sensor has a major malfunction that causes it to fail and pop up an airbag sensor light even when someone is sitting in the seat, Mini USA did not issue a recall but rather a reimbursement form for owners in 2017 the last year of production for that car and did not publicly disclose this. I feel as though this should be a recall as it is common enough for bypass devices to be normal for this car

[XXX]. Mini Cooper 2007-2013: Recalls and TSB. My car is part of a recall under MINI Recall for Timing Chains. I understand now it was settled as part of a class action lawsuit that extended the warranty. I always take my car to a dealer and now after mileage they told me that they want me to pay out of my pocket. My car is a 2007 S. My mileage is 105,000K miles. The recall notice is for the year of my car and they are saying my car is too old and the mileage. This recall is for the year of my car so I am not understanding. Upon inspection by the dealer, it and needs to be replaced and cost $4,100.00. I don't have that kind of money. . My name is [XXX], [XXX]., [XXX], [XXX]. Phone #[XXX]. The dealership is Mini Cooper 1660 E.Spring Street, Long Beach Ca 90806. I never received this recall notice and knew of this only because I took my car to the dealer for something else related for the 3rd time.

The contact owns a 2007 Mini Cooper. The contact received notification of NHTSA Campaign Number: 23V337000 (Electrical System); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated the key fob failed to lock and unlock the vehicle, causing the contact to manually lock and unlock the vehicle. The contact also stated that the radio would change stations or power off independently. The vehicle had been taken to an electrician who referred the contact to the dealer. The dealer was contacted. The manufacturer was made aware of the failure. The failure mileage was 153,000. VIN tool confirms parts not available.

The open recall for this vehicle has been open for 15 months now. Meanwhile my wife's car remains broken down with a bad footwell module due to the exact reason the recall is being issued. I contacted mini and they said I'd have to pay for repairs out of pocket and apply for reimbursement after they come up with a remedy. I have issues with this for a few reasons. First, the repair is costly. Second, it's already been over a year since the recall has been issued, and still no remedy so who knows when they'll actually have one. Third, they said that even if I pay for repairs out of pocket there's no guarantee I'd get reimbursed for them. In my opinion, for something as serious as this recall, the manufacturer should be on the clock to determine the remedy and repair customers cars. It would be nice if BMW/Mini would get some pressure to get this resolved so the my wife and the thousands of other people affected by this can enjoy the vehicles they spent their hard earned money on without worry that it might spontaneously burst into flames.

The contact owns a 2007 Mini Cooper. The contact stated while operating the vehicle, the check engine, ABS, and Dynamic Stability Control (DSC) warning lights remained illuminated, and the vehicle lost motive power and stalled. The vehicle was taken to the local mechanic who diagnosed that the foot well control module was faulty and needed to be replaced. The vehicle was not yet repaired. The local dealer was notified of the failure and the contact was informed that the VIN was not included in NHTSA Campaign Number: 23V337000 (Electrical System). The contact stated that the vehicle had experienced the failure listed in the recall. The manufacturer was not yet contacted. The failure mileage was 130,000.

The vehicle has been presenting issues with breaks, electrical issues, turning off while driving, misfires, air bags don't work, ADAS sometimes don't work, the vehicle chokes and has difficulty running at times, among other issues. There has been a recall since last year and I've tried contacting the manufacturer multiple times, but the issue has not been fixed yet. All of these problems are a great safety hazard for me and my family while on the road.

My Mini Cooper was rendered unsafe to drive as most of the exterior lights (i.e., headlights, brake lights, turn signals) stopped working--all at once. A local mechanic verified that the electrical short resulted from a severely corroded Footwell Control Module, which is the subject of the recall (Recall No. 23V-337, July 2023) for which a "Remedy is Unavailable." When contacted, a case management specialist of BMW of North America could tell me only that a remedy is not yet available. Again, the car is unsafe to drive as it lacks exterior lighting. As such, I am forced to purchase another vehicle as the Mini Cooper sits unusable.

The contact owns a 2007 Mini Cooper. The contact received notification of NHTSA Campaign Number: 23V337000 (Electrical System) however, the part to do the recall repair was not yet available. The local dealer was not contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

[XXX] . Airbag sensor recall. My car is part of a recall under MINI Recall 23V-xxx: Footwell Module. I took my car to a dealer and they told me that they would not repair it because my car is a 2007. My mileage is 102,000K miles. The notice says Im covered but they say im not. The recall notice is for the year of my car and they are saying my car is too old. This recall is for the year of my car so I am not understanding. A light comes on that shows the passenger airbag. Upon inspection by the dealer, it is a faulty seat mat sensor and needs to be replaced and cost $2,120.56. I dont have that kind of money. This should be addressed under the recall. My name is [XXX] , [XXX] . Phone [XXX] . The dealership is Mini Cooper Downtown Los Angeles. 6333 S Almeda Los Angeles Ca 90001. I never received this recall notice and knew of this only because the light indicator came on. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The contact owns a 2007 Mini Cooper. The contact received notification of NHTSA Campaign Number: 23V337000 (Electrical System) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue and confirmed that parts were not yet available. The manufacturer was made aware of the issue and confirmed that parts were not yet available. The contact had not experienced a failure. VIN tool confirms parts not available.

I was notified in July 2023 by NHTSA of the potential failure of the Footwell Control Module and subsequent potential "thermal event which could increase the risk of a fire of injury." Apparently, a fix for this issue has not been developed yet. I am afraid to keep my car in the garage, which is attached to my house. 7 months. Does BMW engineering really not know how to replace this poorly-designed component?

Seat belt warning for passenger seat stays on despite buckling the seat belt. I suspect the air bag deployment is therefore not functioning.

The contact owns a 2007 Mini Cooper. The contact received notification of NHTSA Campaign Number: 23V337000 (Electrical System) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue and confirmed that parts were not yet available. The manufacturer was made aware of the issue and confirmed that parts were not yet available. The contact had not experienced a failure. VIN tool confirms parts not available.

Restraint System Malfunction Fault in passenger-restraint system effecting airbag, belt tensioner or belt-force limiter. Having to replace passenger seat or sensor to indicate I have a passenger so the airbag will deploy. It looks like there may have been a recall for this in the past according to an article I found, but my VIN does not come up as needing this item replaced. Cost is approximately $800.

The contact owns a 2007 Mini Cooper. The contact received notification of NHTSA Campaign Number: 23V337000 (Electrical System) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue and confirmed that parts were not yet available. The manufacturer was made aware of the issue and confirmed that parts were not yet available. The contact had not experienced a failure. VIN tool confirms parts not available.

The contact owns a 2007 Mini Cooper S. The contact stated that while driving approximately 35-40 MPH, the parking brake engaged, and the vehicle came to a stop. The contact manually pulled the parking brake lever several times until the parking brake released. There were no warning lights illuminated. The vehicle was taken to an independent mechanic, who was unable to determine the cause of the failure. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was not contacted. The failure mileage was approximately 48,000.

On 2014 a Class Action Lawsuit was filed against BMW OF NORTH AMERICA for claims regarding MINI COOPER models. Answering your questions as follows: -The failing component was the timing chain tensioner -Yes, engine stalled at any speed -No, dealer did not acknowledge the real problem -No, dealer did not told me about the Class Action Lawsuit, did not advice me of any preventive repair or to install a new timing chain tensioner, when the component failed dealer told me that the problem was a jumping timing chain ; the same excuse as in the lawsuit. -There was only an engine light, not any other warning light There were two repairs, the first for $ 2,629.10 on 6/18/2016 the second for $ 3,354.93 on 1/13/2017 dealer had a two years parts and labor warranty that didn't honor and in 2016 the lawsuit was active and not of my knowledge. My question is: if the production numbers engraved on the timing chain tensioner cylinder face match or are part of the production batch from the factory for which the class action lawsuit took place ? Numbers top line: 7565868 80-02 Lower line: IV/ IS GERMANY 3 1 0 This is looks like half cero All components (parts) and the vehicle are available for inspection. Once engine is out of timing pistons will hit the valves (interference engine), in my engine broke at least one valve seat, pieces fell into combustion chamber getting stuck between pistons and cylinder walls scratching these, result lost of compression, engine die. Engine was beyond any repair, and still was charged for. Lawsuit for vehicles manufactured goes to April 2007 mine was February 2007 Neither the MINI COOPER dealer or BMW North America corporate offices paid any attention to my complaint.

There is a warning light of airbag. But it havent reported when i purchased by a previous owner and carfax as well

2007 mini cooper s airbag light with warning on navigation screen saying seat belt tensioner or belt force limiter has a problem and passenger airbag is off. Odometer is 76,000 when problem started.

TL* THE CONTACT OWNS A 2007 MINI COOPER. THE CONTACT STATED WHILE AT A STANDSTILL, THE VEHICLE BEGAN TO EMIT SMOKE FROM THE ENGINE COMPARTMENT. THE CONTACT STATED CHECK ENGINE WARNING LIGHT WAS ILLUMINATED. THE VEHICLE WAS TAKEN TO LOCAL DEALER SCHOMP MINI (1001 PLUM VALLEY LN, HIGHLANDS RANCH, CO 80129 (303) 872-5752) WHERE IT WAS DIAGNOSED THAT THE THERMAL HOUSING NEEDED TO BE REPLACED. UPON INVESTIGATION, THE CONTACT ASSOCIATED THE FAILURE WITH NHTSA CAMPAIGN NUMBER: 18V248000 (ENGINE AND ENGINE COOLING) HOWEVER THE VIN WAS NOT INCLUDED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER HAD NOT BEEN INFORMED OF FAILURE. THE FAILURE MILEAGE WAS APPROXIMATELY 138,867.

PASSENGER OCCUPANCY AIRBAG SENSOR FAILED, MINI HAS OFFERED A RECALL FOR SIMILAR MODELS BUT ONLY THE CONVERTIBLE AND NOT THE HARD-TOP; HOWEVER THIS IS A PROBLEM FOR THE NON CONVERTIBLES. IT'S INCREDIBLY UNSAFE FOR THE SENSOR TO GO OFF AND NOT BE RESET. I WOULD LIKE MINI TO RECALL AND REPAIR ALL MODELS WITH THAT SENSOR THAT FAILS, NOT JUST CONVERTIBLE MODELS.

VEHICLE WAS STATIONARY IN MY DRIVEWAY, WAS NOT STARTED AND WAS UNATTENDED, HAD NOT BEEN STARTED IN OVER A WEEK AND KEYS WERE NOT IN THE VEHICLES. THE VEHICLE SPONTANEOUSLY BURST INTO FLAMES WHICH BURNED THE ENGINE BAY AND FRONT END OF THE CAR BEFORE THE FIRE DEPT. ARRIVED AND EXTINGUISHED THE FIRE WITH FOAM. THE CAR HAD BEEN SITTING UNSTARTED FOR OVER A WEEK. I AM UNSURE OF WHAT CAUSED THE FIRE AND BECAUSE OF THE EXTENSIVE DAMAGE TO THE ENGINE BAY I COULD NOT DETERMINE WERE THE FIRE ORIGINATED. PERHAPS A PROFESSIONAL FIRE EXAMINER COULD DETERMINE THAT. I AM BLESSED THAT THIS DID NOT HAPPEN WHILE PARKED IN MY GARAGE BUT WAS SCARY. I JUST WANT THIS INCIDENT ON RECORD SO THAT OTHERS WHICH OWN THIS PARTICULAR TYPE OF VEHICLE CAN BE WARNED ABOUT THE POTENTIAL DANGERS. I HAVE OWNED THIS VEHICLE SINCE NEW AND HAD A COUPLE OF UPDATES DONE PER BMW SUCH AS THE TAILPIPES AND TIMING CHAIN IN THE ENGINE. I WAS NOT AWARE OF ANY ADDITIONAL RECALLS OR UPDATES BUT APPARENTLY THERE HAVE BEEN SOME INCIDENCES OF FIRES SUCH AS MINE WHICH I LEARNED ABOUT AFTER SEARCHING THE INTERNET TO SEE IF SIMILAR ISSUES HAD BEEN DOCUMENTED. I WILL ATTACH A FEW PICTURES FOR YOU TO HELP WITH YOUR ASSESSMENT. THANK YOU FOR YOUR TIME AND CONSIDERATION. I HOPE THIS INFORMATION WILL BE SOME HELP TO OTHERS IN PREVENTING A SIMILAR SITUATION. I THANK GOD NO ONE WAS INJURED OR PROPERTY DAMAGED OTHER THAN MY CAR. THE FIRE DEPARTMENT MADE A REPORT BUT IT DID NOT INCLUDE INVESTIGATING THE CAUSE JUST A RESPONSE TO A FIRE. *TR

VACUUM PUMP AND WATER PUMP NEED TO BE REPLACE

THERMOSTAST HOUSING REPLACEMENT AND WATER PIPE. COOLING SYSTEM NEEDS TO BE FLUSH. ENGINE REBUILD DUE OVER HEATING. OXYGEN SENSOR REPLACEMENT. TIMING CHAIN REPLACEMENT. THERMOSTAST REPLACEMENT.

PROBLEM 1: CLUTCH/TRANSMISSION FAILED AT 50,000 JUST AFTER WARRANTY. UNABLE TO SHIFT ON HIGHWAY, HAD TO STAY IN LOW GEAR. TRANSMISSION WAS REPLACED. IT FAILED A SECOND TIME, WAS REPLACED AT ABOUT 80,000. I BELIEVE IT IS FAILING AGAIN AS THE CLUTCH IS SLIPPING IN 1ST AND 2ND GEARS; MINI COOPER SAYS THEY NOTE NO PROBLEM. PROBLEM 2: TIMING CHAIN. PARKED, MY CAR WOULD NOT START EASILY; STARTED ON 3RD TRY. MY CAR STALLED, STOPPED ON THE HIGHWAY AS I WAS SLOWING DOWN DUE TO TRAFFIC. RESTARTED AND CONTINUED. NO ENGINE LIGHT. DRIVING TO MINI SERVICE, CAR STALLED COMING IN; HAD TO COAST IN. FOUND TO BE TIMING CHAIN, VALVETRONIC ECCENTRIC SHAFT, PERHAPS PARTS FALLING INTO OIL PAN. $2800 IN REPAIRS. WHEN I ASKED ABOUT LAW SUITS OR RECALLS OVER THE LAST 3 YEARS BECAUSE I'VE HAD MAJOR PERFORMANCE ISSUES, MINI COOPER STATED NO KNOWN SUITS EVEN THOUGH THERE WERE. I FIND THAT THERE HAVE BEEN SUITS, AND I "MISSED THE WINDOW" FOR THE TIMING CHAIN.

PASSENGER SEAT MAT SENSOR ON 2007 MINI COOPER FAULTED. THERE WAS A RECALL ON BMW AND MINI COOPERS EXCEPT FOR THIS BASE MODEL. DEALER SAID IT WOULD BE $1800. TO FIX I WOULD THINK THE PARTS FOR THIS CAR ARE THE SAME. SHOULD BE RECALLED.

PASSENGER SEAT MAT OCCUPANCY SENSOR/PAD HAS GONE BAD AGAIN AFTER THE RECALL.*DT SAFETY RECALL REPORT XXX-XXX 'PARTS OF THIS DOCUMENT HAVE BEEN REDACTED TO PROTECT PERSONALLY IDENTIFIABLE INFORMATION PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).' *JB

I HAVE BEEN DRIVING MINI S 2007 FOR MORE THAN A YEAR WITH NO SERIOUS ISSUES OTHER THAN ONE CHECK ENGINE LIGHT ISSUE, WHICH WAS RESOLVED SIMPLY BY A MECHANIC CHECK AT BMW SERVICE CENTER. ON SUNDAY EVENING MAY 26, 2019, AS I WAS PLANNING TO GO OUT, I OBSERVED THE STEERING ALERT SIGN ON. I TRIED RESTARTING AND SHUTTING OFF ENGINE MULTIPLE TIMES THINKING IT MAY BE AN ELECTRONIC ABERRATION WHICH MAY BE KICKED AWAY BY BRUTE FORCE OF RESTARTING THE IGNITION. AFTER 30-45 MINUTES OF THIS FRUITLESS EXERCISE, I TURNED MY ATTENTION ONLINE WHERE I FOUND NUMEROUS AUTO BLOGS OF STARTING THE CAR WITH JUMPERS BATTERY TO REPLACING POWER STEERING FLUID. SINCE MINI SERVICE WAS CLOSED, I HAD TO SEEK HELP FROM MY INSURANCE COMPANY. THEY SENT A PERSON AFTER TWO HOURS TO USE JUMPERS, BUT THAT DID NOT HELP EITHER. WE WERE ABLE TO CHECK THE POWER STEERING FLUID , AND THAT WAS ALSO FULL TO THE MARK. ON FURTHER RESEARCH ONLINE, I DISCOVERED TO MY UTTER DISAPPOINTMENT THAT MINI COOPERS HAVE BEEN PLAGUED WITH POWER STEERING ISSUES DUE TO INHERENT FLAW OF PLACEMENT AND DESIGN OF POWER STEERING PUMP. IT IS VERY WELL DOCUMENTED ACROSS REPUTED CAR JOURNALS/MAGAZINES THAT THE POWER STEERING PUMP FAILURE WILL DEFINITELY HAPPEN IN MINI COOPERS, AND THE ONLY VARIABLE IS THE TIME. I WAS THOROUGHLY CRESTFALLEN GIVEN I HAD PLACED SO MUCH TRUST IN THE BRAND AND THE QUALITY OF MINI COOPER. THE PURPOSE OF THIS COMPLAINT IS TWO PRONGED- ONE IS OBVIOUSLY TO HIGHLIGHT THE PROBLEM ONCE AGAIN AND MAKING SURE MINI ENGINEERS SOLVE THIS PROBLEM IN THEIR ENGINEERING DESIGN PROCESSES. SECOND- IS TO REQUEST TO HAVE THE POWER STEERING ISSUE FIXED IN MY CAR BY MINI. GIVEN THAT THE ISSUE HAS BASIS IN THE INHERENT FLAW OF THE DESIGN, I BELIEVE MINI COOPER WILL WAIVE OFF THE COST OF SERVICES AND PARTS TO GET THIS ISSUE FIXED. THIS IS NOT USUAL WEAR AND TEAR WHOSE COSTS SHOULD BE BORNE BY THE CUSTOMER.

THE TURBOCHARGER HAD TO BE REPLACED, NEW TURBO GOT HOT AND MELTED THE VALVE COVER. THEN THE TURBOCHARGER CAUGHT FIRE WHILE IN MOTION IN A RURAL NEIGHBORHOOD. ALL WITHIN 6 MONTHS.

TIMING CHAIN TENSIONER BROKE AND MESSED UP THE ENGINE

TO THE RIGHT OF MY GAS PEDAL IN MY CAR GETS SUPER HOT! IT REACHES OVER 207 FAHRENHEIT DEGREES. IT GETS WORSE WHEN I USE MY AC. WHEN I WEAR MY FLIP FLOPS IT BURNS MY TOES.

TL* THE CONTACT OWNS A 2007 MINI COOPER S. THE CONTACT STATED THAT THERE WAS A CATASTROPHIC ENGINE FAILURE WITHOUT WARNING. THE VEHICLE WAS UNABLE TO BE DRIVEN AND WAS TOWED TO BRAMAN MINI OF PALM BEACH (2815 OKEECHOBEE BLVD, WEST PALM BEACH, FL 33409, (561) 257-4774). THE DEALER INDICATED THAT THE MANUFACTURER SERVICE CAMPAIGN WAS ONLY TO ADDRESS REPLACING THE TIMING CHAIN AND THAT THE REPLACEMENT OF THE ENGINE ASSEMBLY WAS NOT INCLUDED IN THE MANUFACTURER'S GUIDELINES OF THE SERVICE CAMPAIGN. THE VEHICLE WAS NOT REPAIRED. THE CONTACT WAS WAITING FOR A RESPONSE FROM THE MANUFACTURER TO DETERMINE IF THEY COULD APPROVE THE DEALER REPLACING THE TIMING CHAIN AND THE ENGINE ASSEMBLY. THE FAILURE MILEAGE WAS NOT AVAILABLE.

MY VEHICLE IS CURRENTLY @ BRAMAN BMW WPB (5612423210) FOR A TIMING CHAIN PROBLEM WHICH WAS UNDER RECALL. THE SERVICE ADVISOR CALLED ME AND NOTIFIED ME THAT THE TIMING CHAIN BROKE INSIDE THE ENGINE & COMPLETELY DESTROYED THE MOTOR. TE TIMING CHAIN JOB ALONE ESTIMATE IS $3800, BUT THEYVE NOTIFIED ME THAT THE ENGINE IS UNREPAIRABLE & MUST BE REPLACED! THEY ALSO FAILED TO ACKNOWLEDGE THAT THIS HAPPEN WHILST DRIVING ON AN INTERSTATE, ALMOST CAUSING A HUGE ACCIDENT!! PLEASE HELP!! MINI APPARENTLY CARES MORE ABOUT MONEY THAN LIVES!!