Mazda CX-5 2016 — Problemas relatados

My windshield wipers stopped working completely. I am unable to see out my front window properly while its raining. Yes the dealership said that my front body control module needs to be replaced which is the same issue that other Mazdas from the same era have had safety recalls for (nhtsa campaign 19v272000). No it hasn't been inspected by anyone other than a Mazda dealership. The front wipers slowly stopped working. First the highest setting didn't work at all, then the wipers would work sporadically, and now they don't work at all.

I own a 2016 Mazda CX-5 Grand Touring and discovered two brown, burn-like marks on the lower seatback of a heated front seat. I suspect the seat heater overheated and damaged the upholstery. The discoloration is concentrated in the lower back/lumbar area, and I have photographs documenting it. I am concerned that continued use could cause further overheating, burns to an occupant, or a fire. I am reporting this as a seat-heater safety defect and requesting investigation.

Rear subframe corrosion on this vehicle. I am in a winter road salt region, the materials used for this vehicle's subframe are not compatible with consistent driving in this region. Similar vehicles (not mine?) were subject to a recall for the front subframe, but nothing for the rear. This rear subframe issues caused multiple failures of virtually every component of the rear suspension - control arms, rear springs, etc. The repair cost for JUST the subframe was $3813. Not repairing it was not an option - the vehicle had failed mandatory State of Maine inspection (a safety thing, if I'm not mistaken). This should be a Mazda problem, not a me problem. I contacted Mazda USA about this issue and got no response.

Rear subframe corrosion on this vehicle. I am in a winter road salt region, the materials used for this vehicle's subframe are not compatible with consistent driving in this region. Similar vehicles (not mine?) were subject to a recall for the front subframe, but nothing for the rear. This rear subframe issues caused multiple failures of virtually every component of the rear suspension - control arms, rear springs, etc. The repair cost for JUST the subframe was $3813. Not repairing it was not an option - the vehicle had failed mandatory State of Maine inspection (a safety thing, if I'm not mistaken). This should be a Mazda problem, not a me problem. I contacted Mazda USA about this issue and got no response.

The contact owns a 2016 Mazda CX-5. The contact stated while driving at an undisclosed speed, the electric parking brake module warning light was illuminated and the "Brake failure. Vehicle unsafe to drive," message was displayed on the instrument panel. The vehicle was taken back to the residence. The failure occurred on several different occasions. The contact expressed concern that the brakes could engage while the vehicle was in motion. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure. The failure mileage was approximately 84,000.

Repeated Failure and Rebooting of Mazda Connect Infotainment System I am the owner of a 2016 Mazda CX-5. The factory Mazda Connect infotainment system has developed a recurring defect in which the system repeatedly reboots to the Mazda logo while driving. Prior to complete failure, the navigation system became intermittent and Bluetooth connectivity frequently disconnected, requiring repeated attempts to reconnect devices. The system now continuously cycles through the startup screen, making navigation, hands-free phone functions, and system settings inaccessible. These repeated reboots occur while the vehicle is in motion and are distracting to the driver. The flashing and rebooting screen repeatedly draws the driver's attention away from the road and interferes with the use of navigation and hands-free communication features that are intended to promote safe driving. After researching this issue, I found numerous reports from other Mazda owners experiencing the same symptoms involving the Mazda Connect system, navigation SD card, and Connectivity Master Unit (CMU). The frequency and similarity of these reports suggest that this is a widespread and well-known defect rather than an isolated incident. Because this defect affects driver attention and the safe operation of the vehicle's communication and navigation functions, I respectfully request that Mazda and the National Highway Traffic Safety Administration investigate this matter and require Mazda to issue a recall or establish a repair program for affected vehicles. Vehicle: 2016 Mazda CX-5 Mileage: 70k

The contact owns a 2016 Mazda CX-5. The contact stated that while driving 70 MPH with the cruise control activated, the cruise control cancellation switch failed to operate as intended after several attempts or while depressing the brake pedal. No warning light was illuminated. In addition, the contact was able to deactivate the cruise control using the main cruise control power switch. The vehicle was taken to a local dealer to be diagnosed; however, the cause of the failure was not yet determined. The vehicle was not repaired. The manufacturer was made aware of the failure by the local dealer. The failure mileage was approximately 91,000.

In 2024 I started having problems with my battery replaced it 3 times last time with a Mazda battery per Mazda advice. The car started to jerk while driving took it back to Mazda said it could be fuel injectors. They cleaned them and problem persists. Took it back they cleaned purve valve and then I broke down while leaving on [XXX] . Called service dept called police since it was in the middle of the blvd. And in traffic. We were lucky no one hit us. They took my car gave me a loaner had it for 10 days. Couldn’t find any problems. Then in 4/2025 it completely died at my home I called Mazda they were able to jump the battery and had it for a month. Couldn’t find any problem. And now we are in 5/2026 my car was in my drive without out being driven for 3 days and now is dead once again. But it is so dead that I cannot open with fob and dash board is black. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The contact owns a 2016 Mazda CX-5. The contact stated that the engine light illuminated. The vehicle was taken to an independent mechanic diagnosed with a sensor failure and needing to replace a catalytic converter. The oxygen sensors were repalced.r was replaced by an independent mechanic. The vehicle stalled while reversing. The manufacturer was not notified of the issue. The approximate failure mileage was 131,860.

(I am the owner of the car and am filling this out for my daughter who was driving it at the time, I was not with her during the incident) While driving down the road in the rain the wipers just stopped working. I have not had any dealers ID the specific problem yet. We replaced the wiper 20amp fuse and it did not fix the problem. There were no warning lamps and there are still no warning lamps. My safety was put into danger when I could not see out the window. I was nearly at work so I waited for the rain to slow down some was able to make it to work. The rain cleared while I was at work and it has not rained since. It is available for inspection upon request.

Any time the vehicle has been sitting with the engine off and has been given enough time to “cool down”, upon starting the vehicle and switching from PARK to DRIVE, the vehicle will violently lurch forward while attempting to reach 2nd gear. This is dangerous behavior that is not normal for any vehicle. There is clearly something wrong with either the transmission or the way the software communicates with the transmission. When the engine is within normal temperature it doesn’t display this dangerous behavior. A similar TSB was issued for the 2nd generation of CX5s but not for this generation of CX5s

I was slowly turning left into an alley when I heard a loud noise, the front of my car dropped, and the car immediately stopped and was immovable. Upon getting out of the car, it appears some joint separated from the wheel.

My wife was driving our 2016 Mazda CX-5, and was getting ready to pull into our daughters' driveway. My wife slowed down to a stop before entering the driveway. She gave the vehicle some gas to move forward. She stated that there was a pause, then the vehicle accelerated forward slamming into the garage door and the corner of the garage/house. There was also a Tesla parked inside the garage that was knocked back about a foot and a half. The distance from the edge of driveway and street to the garage door is about 27 feet. This happened at 1:30 PM. The weather conditions were great, sunny and dry. Thankfully, no one was hurt. If my wife was another foot to the right, she would have hit the support post for the upper balcony, and there would have been a good chance of the balcony falling on top of her. Or, if someone was standing in front of my wife when she entered the driveway, they could have seriously been hurt! There were no warning lights on prior to the accident. This happened last Sunday, April 19, 2026. We had the car towed to a local body shop on the same day as the accident. The vehicle was towed away the very next day to our insurance company's salvage lot in Bakersfield. I do have all the information, address and phone number, of the lot where our car was towed to. Hopefully, the car can still be inspected by the proper authorities. Thank you for your time!

The contact owns a 2016 Mazda CX-5. The contact stated that while driving at an undisclosed speed, there was an abnormal sound coming from the vehicle, and the message “Smart Brake Malfunction” was displayed. The vehicle was taken to an independent mechanic, where it was diagnosed with catastrophic brake caliper failure. The contact was unsure if the vehicle needed to be repaired. The vehicle was then taken to the dealer, where it was diagnosed, and it was determined that the passenger’s side inner CV joint had failed and needed to be replaced. The vehicle was not repaired. The dealer informed the contact that the vehicle could not be driven due to the severe failure. The manufacturer was not made aware of the failure. The approximate failure mileage was 125,385.

High pressure fuel pump has been replaced twice in less than a year. Car has less than 100,000 miles. Both times the fuel pump went out while driving, causing loss of acceleration and stalling of vehicle. Had to be towed to shop both times.

Vehicle was taken to an authorized Mazda dealership for 60,000-mile service; coolant system drained and refilled. Immediately after service, check engine light illuminated (P011A – engine coolant temperature sensor correlation issue). Dealership retained vehicle, drove ~300 miles, performed a second coolant flush; issue persisted. Dealer determined heater core clogged, attributed to coolant contamination/corrosion introduced during service. Another CX-5 at the same dealership experienced the same issue. Safety Concerns: Heater and coolant system failure may affect cabin comfort and engine temperature monitoring. Occurred immediately after authorized service, suggesting procedural or system-related defect. Noted in Mazda Technical Service Bulletin 07-007/19 as a known issue. Attempts at Resolution: Mazda offered partial goodwill assistance (~$775–$875) and assigned partial responsibility to the customer. Multiple attempts to escalate with Mazda Customer Experience (Case manager Betty) have not resulted in a satisfactory resolution. Dublin Mazda dealership service department, Mr. Frank Gozales (866-502-9912) mentioned original coolant by Mazda has caused this issue on 2016, and 2017 Mazda CX5 and is Mazda problem. I am requesting NHTSA review of this issue for potential defect or safety investigation.

My screen begins to change the display without me touching it. It has interrupted my GPS directions, causing me to get lost. It has gotten worse over time, now causing my back up camera to either not display at all or become partially blocked by another application randomly starting on the screen. My emergency brake lights flash on my dash, and auto technicians tell me it is a malfunction with the electrical system, not something in my brake system that needs to be replaced. We have tried that. These problems I have been told are not the responsibility of the manufacturer. I don’t understand why. It is distracting, alarming, and because it is getting more frequent with more systems being affected, it puts the driver in danger. This is not due to wear and tear - it is due to a faulty electrical program.

The fuel pump system needed to be replaced completely, although the mileage is just around 60000 miles.

Airbag light is flashing. Independent shop found code B00C1:93-8B. OCS Sensor B. Shop sent owner to dealer for inspection & repair. Charged 57.24. Dealer found DTC B00C1 passenger seat occupant classification sensor b. Replacement cost for the part 1,110.13, plus shop fess and tax for a total repair cost of this critical safety item would be 1,197.29. I did not have this service performed due to the high price. This safety item should be covered by the manufacturer. I recently learned that a dealer may not sell a car with this safety issue so I want it fixed and covered by Mazda.

I noticed smoke filling the inside of my car. I looked over at the passenger seat, and my coat was on fire. I poured my drink on it, pulled over, and threw the coat out of the car. I saw a large hole in the lumbar area of the passenger seat, and it was glowing red and putting out a lot of heat. The seat heater was on, so I immediately turned it off. It was obvious that the fire has started inside the seat, and there was no other fire source in car--ie. lit cigarette, lighter, etc. If someone had been sitting there, they would have serious burns. The seat will need to be replaced.

Leather heated seats .. safety put at risks because I suffered burns on my bottom (butt) from the driver seat getting too hot to the point where it burned the seat itself as well , and made a brown burn mark on the seat … Both of my cheeks got burned .. this can in the long run cause skin damage and worse case scenario cancer. No it hasn’t been inspected No warning lamps

With no prior warning, just after turning into driveway, my car got stuck and would not move. It gave clicking sounds and would not move no matter which gear it was in. The towing service person needed a dolly in order to safely lift the vehicle onto the towing bed because the front, driver’s side tire would not move and was pushing into the fender. So far, the control arm and axel are completely separated from the car. Further investigation is ongoing to determine the extent of the spontaneous injury. This all happened without warning.

Passenger side seat heater overheated and burned upholstery.

I was driving down the road and started smelling smoke then looked over and my passenger seat was in flames.

THE FRONT PASSENGER SEAT HEATING SYSTEM CAUGHT FIRE AND BURNED THROUGH THE FABRIC AND MY DOG'S SEAT. THE FUMES MADE ME AND MY DOG NAUSEOUS.I HAD TO SWERVE ACROSS THE HIGHWAY AND STOP ON THE SHOULDER TO EXTINGUISH THE SEAT FIRE/BURN. THE FUSE WAS PULLED FOR SAFETY. THE SEAT IS IN STORAGE FOR INSPECTION. MAZDA WILL BE CONTACTED.

UNKNOWN Slowly driving into garage when suddenly the engine revved up loudly and unattended accelerated forward, causing extensive damage to front of car, a piece of furniture and garage wall

The airbag warning light is on. I’m concerned the airbag may not deploy in an accident. There was a recall on the airbag, but the dealership only reset the light and did not replace the airbag. I have taken my car to two different Mazda dealerships: One told me I would have to pay for the airbag replacement. The other said the airbag is functioning properly. I’m not sure which one is correct, but the warning light continues to come on. Sometimes it stays on for a couple of days; other times, it flashes on and off intermittently. The airbag light is clearly visible on the dashboard and continues to behave abnormally.

The vehicle's air conditioner expansion valve is defective/malfunctioning. While driving the vehicle with the air conditioning operating a loud whooting noise fills the interior of the vehicle. The noise sounds like the siren/hooting sound the police make when they want you to pull over or get out of their way. But the sound is loud and comes from inside the car jarring the driver and passengers. I purchased the car in early 2017 new. I first noticed the AC issue in the summer of 2018. I brought it up to Herzog-meir mazda (where i bought the car) when scheduling an oil change. they said they could not replicate it and so there was nothing they could do. I brought it to them at least 4 times with the same issue. Each time they sent me on my way and said they couldn't replicate it. I brought it up to Foothills Mazda in Spokane in 2023 and again they said that they couldn't replicate it and sent me on my way. This past august i had to schedule the car for an update covered by a class action lawsuit and had them look at the noise issue again. Prior to scheduling I has research online if others have had the issue and low and behold lots of mazda owners have. It is a known issue that mazda has created a "helpline" to deal with it. So I brought it up while scheduling it and asked to make sure they researched the AC expansion valve prior to my appointment (more than a month out). The Mazda lady that scheduled my appointment heard the noise several times with I was idiling the car and finishing scheduling the appointment. The first available appointment wasn't until Oct 1st so of course it wasn't hot enough outside to replicate the situation that causes the noise. Again, they charged my the diagnostic fee and sent me on my way. [XXX] [XXX] [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Rear Shock mount deteriorated in 8 years, far quicker than industry standard. Mazda redesigned the part for 17' MY. Widely reported on Reddit. NHSTA service bulletin notice.

Our sunroof exploded while we were driving on the highway. Glass shattered on us and fell while we were driving with a very loud explosive noise.

Mazda issued a safety recall (Mazda safety recall 4320A, NHTSA campaign number 20V-063) to address daytime running light flickering/failure. At the time, only the passenger side daytime running light was replaced under the recall by Mazda, with a gasket/gas absorption sheet being installed on the driver's side. The driver's side daytime running light is now flickering/dim. Mazda did not repair the safety defect properly on the driver's side for the daytime running lights under Mazda safety recall 4320A, NHTSA campaign number 20V-063, because Mazda only installed the gasket/gas absorption sheets that have since failed, causing the daytime running lights to flicker, increasing the risk of crash. Mazda has refused to cover the cost for replacement of the daytime running lights per safety recall notice 4320A / NHTSA 20V-063, even though replacement of these lights is covered by the recall. Both a Mazda dealer and Mazda corporate customer service have been contacted regarding this issue and both have refused to provide the remedy as outlined in the safety recall. Mazda has provided an estimate of $1,466 to replace the daytime running lights. Attached Documents: -Correspondence with Mazda where Mazda's refuses to cover work -Estimate from Mazda to perform work -Original invoice from recall work performed (gasket kit on driver side only, not full light replacement)

The contact owns a 2016 Mazda CX-5. The contact stated that while driving 60 MPH, the vehicle failed to accelerate as intended while depressing the accelerator pedal. No warning light was illuminated. In addition, there was an abnormal rattling sound coming from the engine. The contact pulled over to the side of the road before the vehicle stalled. The vehicle failed to restart. The vehicle was towed to an independent mechanic who determined that the engine had failed due to a lack of maintenance. The contact stated that the vehicle was equipped with an automatic reminder regarding the oil change. The contact stated that the oil change reminder failed to illuminate to indicate that the oil level was extremely low. The check engine warning light also failed to illuminate. The vehicle remained at the dealer unrepaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 130,000.

Only one headlight was addressed by dealer in repair for 4320A | NHTSA #20V-063 and they're refusing to cover the other side. The other DRL led light is now out from seemingly the same cause. They stated they did not fully follow the procedure in the documents I found regarding this recall when they repaired the first one because they "pre authorized" the swap of one side on "good faith" so there is not a record I can cite around the serial or lot numbers of the new or old lights on my own.

We had another CX-5 in the back that we used to test whether or not it was either the throttle body or the BCM ( Body Control Module ) or the PCM ( Power Control Module ) not working that is causing your vehicle to not wanting to turn on The throttle body passed we transferred it over from vehicle A ( Being the donor ) to vehicle B (Being your vehicle ) and it was still doing the same thing which it would crank but not fully turn on and that is how we ruled that part out The BCM we also transferred over from vehicle A to vehicle B and same thing it would crank but not fully turn on This is what the mechanic at Mazda Collision Center of Irving stated: The PCM has power and is communicating with everything else in the vehicle. If it was the PCM then nothing would work and we wouldn't be able to even cycle the power as if we were going to turn on the vehicle We brought this over to our Mazda Foreman and we showed him the codes it was throwing and what was going on and explained everything and he did tell us that it could be the main harness that is causing all of this he is not for sure just because he is not the mechanic involved in this but he said that is a good start. I am uncertain exactly what is wrong with the vehicle. When I took it in to be serviced, it worked. The mechanic then said he couldn't work on it anymore after trying to fix the body work because the electrical system had failed. I then had it towed to Mazda to see if they could fix the issue. I had originally took it in because of a minor fender bender. I am unclear as to why it has taken four months and my car still doesn't work and I do not know how to afford buying a car to replace it when I cannot trade it in since we cannot resolve the electronic portion through insurance.

The info uni in the car constantly resets itself. It happens when GPS is activated, parking, listening to directions, pretty much at all time especially in crucial moments. Nav center doesn't even load at times, this causes unknown information of speed limits and streets.

Keyless entry stopped working, key fob battery replaced as well as car battery. Coolant issues. Heater core and sensors

The engine light constantly appears along with the "Schedule Maintenance Soon" light. Taken to dealership many times within my 3 month warranty and no definite reason was given.The vehicle rides very bumpy though sway bar was inspected and supposedly repaired by dealership during my 3 month warranty.

my brake light and my emergency brake light stays on and they blink constantly while the engine is turned on. they have been like that for at least a year. both my brakes and the emergency brake both work but I cant get the lights to go out.

Water pump failed causing coolant leaked into engine causing major engine damage

from my service mechanic... "Rear brakes at 8mm/8mm on the right side, but 4mm/6mm on the left. These brakes were replaced 1500 miles ago and should not be showing this kind of wear. Examined brake pads, found evidence of overheating. Scanned vehicle, confirmed no codes from Electronic Parking Brake. Actuated parking brake and confirmed it is engaging and releasing as commanded. Found a Technical Service Bulletin related to parking brake drag on this vehicle. The brake pad damage pattern is consistent with what we observed today. Mazda recommends replacing the affect caliper(s) with an updated version to address this issue. Confirmed by lot number that current calipers are older version. TSB attached. Recommend replacing calipers and rear brake materials."

The front passenger seat warmer caught fire as i was driving the vehicle. No fuse tripped or anything when it over heated. The seat not just melted but actually caught fire and filled the vehicle with smoke.

My 2016 Mazda CX-5 has had ongoing issues with the infotainment. It freezes up in cold weather and the screen goes blank for long periods of time. This has been an ongoing issue with Mazda vehicles. I had to replace the SD Card in December 2024. The cost was $326.50. There is currently a class action lawsuit by Frederick Law Group 836 Philadelphia Street, Indiana, Pa 15701, Phone number 724-801-8555. When the infotainment goes out during phone calls or navigation, it is a distraction while driving. I called Mazda and chatted with Travius about this issue and forwarded by receipt for the part. He said Mazda would not reimburse me. Can the NHTSA help in getting the reimbursement do you have any suggestions?