Ford Mustang 2016 — Problemas relatados

Coolant intrusion caused by a crack in the engine block coolant leaking into cylinder 3, engine replacement needed. 50k miles on the vehicle.

The clutch pedal assembly weld has failed at the pivot point. This is a well known issue in the community and no fix has been made by Ford. The car could NOT shift or move while in the middle of an intersection.

A new Walmart-brand EverStart Plus 96R, 590 CCA automotive battery was purchased on August 4, 2026, and installed in a 2016 Ford Mustang Convertible. On the evening of September 26, 2026, my family and I drove the Mustang and returned home at approximately 11:00 p.m. The vehicle operated normally. There were no warning signs, electrical problems, overheating, or other indications of a mechanical problem. The Mustang remained parked and untouched overnight. At approximately 2:00 p.m., 15 hours later, on September 27, my daughter came into the room and told me that the car was on fire. Riverside County Fire responded to the scene. Fire personnel specifically asked whether the Mustang had been driven or worked on that day. I told them it had not. The vehicle had remained parked since approximately 11:00 p.m. the prior evening. Fire personnel continued to suppress the fire, investigated the engine compartment, cut the battery cables, photographed the vehicle, and advised me that the battery appeared to be the possible source of ignition.

The contact owned a 2016 Ford Mustang. The contact stated that while driving at highway speeds, the driver's side door independently opened. The failure caused severe wind noise to enter the vehicle, and the door ajar warning light illuminated. The vehicle was taken to an authorized dealer, where technicians confirmed that the door latch mechanism had failed and stated that the mechanism was subjected to unintended opening. The vehicle was repaired out of pocket. The contact referenced NHTSA Campaign Number: 20V331000 (Latches/Locks/Linkages) as the cause of the failure; however, the VIN was not included in the recall.

On or about June 24, 2026, the CHECK ENGINE light came on. Since I was near the local Ford Dealership, I stopped there. The car was evaluated the next day. I was told the the gas tank assembly and pipe had to be replaced. The repair was almost $4000. My car only as 63,117 miles on it. Before the problem was diagnosed, I was getting lousy gas mileage and assumed it was because the government was allowing more ethanol. In fact, the problem could have been disastrous... The car could have caught on fire . The car was in the repair shop until July 2, and I had to rent a car for $300. I am unable to download a photo I have of the gas tank which shows these numbers: E-11 34RI-020135 as well as AD46319. I have attached the bills from the CERTIFIED FORD repair shop. Please note that the 2015 Mustangs were recalled for gas tank replacements. I have a 2016.... Seems like my car may have had a faulty gas tank installed as well. The mechanic said he had replaced a couple. Nite that the car had just over 63000 miles

When reaching 60+ mph the passenger door will unlatch and give me the open passenger door notification on the dash. It doesn’t shoot up, but rather barely comes open.

Brought the car in for service. The tech called me back and said the engine was blown. Condensation in cylinder 3. This was due to the cylinder walls being engineered to small. Which caused a leak in the coolant jacket. I paid out of pocket nearly $10,000 to have it replaced because the third party warranty that I had purchased declined my coverage to fix it because it’s a known issue by ford. Bc

See attached document for complaint

This complaint is a formal notification of a Recall Remedy Failure regarding NHTSA Campaign 22V082000 / 25V572000 (Rearview Camera Wiring Harness / Camera Replacement). My vehicle was brought to an authorized Ford dealership on 07/22/2026 to complete the recall remedy. Following the service, the backup camera functionality has completely degraded and is now worse than before the service. The screen is consistently displaying entirely black / distorted screen / Message Camera not available, presenting an ongoing, unmitigated back-over safety hazard. The manufacturer's remedy has failed to resolve the safety defect. Returned to the authorized Ford dealership on 08/21/2026 and was told this is a known issue and there is another "recall" fix for this issue, but parts are now available at this time. I need to follow up in a month or more.

The contact owns a 2016 Ford Mustang. The contact stated that while driving 75 MPH with his daughter inside the vehicle, the driver’s and passenger’s side doors opened unexpectedly. No warning light was illuminated. A dealer was contacted. The vehicle was taken to the dealer to be diagnosed; however, the contact declined to pay the cost for the diagnostic test. The vehicle was not repaired. The contact stated the failure had occurred approximately twelve times with the driver’s side door. The manufacturer was notified of the failure and informed the contact that the vehicle was out of warranty. The approximate failure mileage was 108,787.

Nelson v. Ford Motor Company is a class action lawsuit targeting a defect in Ford's 2.3-liter EcoBoost engines. The suit highlights coolant leaks into engine cylinders, overheating, and catastrophic engine failures. I have had my 2016 ford mustang ecoboost in and out of mechanic shops for months now accumulating well over $7K in out of pocket expenses. I have been to multiple mechanics trying to diagnose and fix the problem but in the end it was a design flaw in the 2016 ford mustang ecoboost 4 cylinder which caused it to leak coolant, misfire, and overheat. I have been having this problem for some time now, this put my safety and the safety of others at risk because I had to slow down dramatically in order to pull over on the freeway due to the engine overheating from coolant loss. I've also experienced problems like trouble starting, rough idling, loss of coolant, and huge clouds of white smoke coming from the exhaust upon start. I have saved every single receipt and invoice breakdown since this problem began. My mechanic has also been documenting everything including taking notes and photographs of every issue. My car is currently in the shop right now being worked on. My mechanic says that he can temporarily patch the problem with a high performance head stud, copper sealant, and an ExtremeHeat metallic repair paste by JB Weld to momentarily solve the issue. He says that he does not know how long this patch will last so he is insisting I either get a new car or to see what my options are regarding the class action lawsuit filed against Ford.

The passenger side door is periodically opening to the first catch while driving on the highway without anyone touching the handle and it does not matter that the door is locked. It is very scary for any passenger when it happens. For the driver the tendency is to try to reach over and re-close the door at highway speed which seems dangerous.

I am experiencing the same issues as NHTSA 22V-011 where the brake pedal stop bumper had disintegrated, causing continuous brake lights and a potential rollaway risk

Break bumper disintegrated, causing the rear bites to stay on and the automatic transmission to be able to switch from Parker to drive causing the vehicle to be able to roll and possibly crash

The rear view camera has a recall. I took the vehicle into a Ford dealership on 6/23/26 for this recall. This is a risk to myself and others because backup cameras are a federally required safety feature. This is my 2nd attempt for Ford to fix this recall at two separate dealerships. Ford does not care about their recalls and the safety of Ford customers! I almost hit another car that was coming out due to the blind spots on that vehicle. My young daughter also drives the car and this is not the 1970’s as young drivers depend on that feature. Ford said that they could not find the problem with this issue and further diagnosing must be done on my part for $198. This is not fair to customers as this was a recall issue. If Ford is not properly training their technicians to diagnose this issue, it should not be the responsibility of the customer to pay for their error in producing this car. The problem has been reproduced and confirmed by a Ford dealership. There were no warning lights or issues that were displayed. Ford only sent out letters stating that a recall was issued on the problem. In May of 2026 my backup camera and trunk was not working. Ford inspected and replaced the parts on the vehicle that they assumed was part of the recall. For a 2016 Mustang, a common cause is not just the camera itself but also wiring/connectors in the trunk area or the APIM/radio module that displays the image. If the dealer simply performed the recall software update or replaced one component and the screen is still blank, the underlying problem may not have been fully diagnosed. This the 2nd attempt to have a recall fixed by Ford but to no avail (2 separate dealerships)

See attached document for complaint.

There are two recalls on this vehicle. South Bay Ford, located just a few miles farther away than Auto Nation Ford in Torrance has no problem with pick up and delivery resources to insure recall work is completed but stated I must use Auto Nation Torrance Ford because I fall into their service area, yet Auto Nation Ford Service Manager contacted on 6/22/2026 @ ~ 4:05 P.S,T. stated they do not have enough people to perform pick and delivery. It would seem to me Auto Nation Ford in Torrance has chosen profits over recall compliance putting lives at risk. I thought this was important enough for you to look into.

The contact owns a 2016 Ford Mustang. The contact stated that while shifted into reverse(R), the rear-view camera was blank and then operated intermittently; however, the image was blurry. The vehicle was taken to a dealer on two occasions. During the first visit, the contact was informed that the harness needed to be replaced. The vehicle was repaired, but the failure persisted. The vehicle was then taken to a different dealer, where it was diagnosed and determined that the camera needed to be reprogrammed. The vehicle was repaired, but the failure persisted during the first inclement weather. The manufacturer was not notified of the failure. The failure mileage was approximately 72,000.

They have a recall for the seatbelt so I got my car inspected and tested and my seatbelts are fine. I use this as a rental car and my business is stopped and I’m losing money every day that I cannot rent this out.

Manufacturer has failed or is unable to remedy this safety recall for your vehicle IN A TIMELY MANNER. The Recall was from September 16, 2025. It has now been OVER half a year with NO remedy. I live in a salty air state and the last thing I want to happen is to drive with a seat belt with reduced effectiveness. I've ALREADY been in an accident a decade ago where a woman T-Boned me. I had a 2001 Mustang Convertible at the time with the convertible down. It's just like this Mustang with the recall but older. Thankfully the airbags and seat belt worked. Something needs to be done asap !!!!

The steering wheel over time is very loose and in my case i need to be very careful with it because I feel I am losing control on my car while driving. You can feel the steering wheel moving up and down without little to know force also while driving. I don't even drive that fast since my way to work is always in a school zones.

The contact owns a 2016 Ford Mustang. The contact stated that while shifted into reverse, the screen turned blue with a message that the back over prevention camera was unavailable. The failure was intermittent. The contact first received notification of NHTSA Campaign Number: 22V082000 (Back Over Prevention). The vehicle was taken to the dealer, who inspected the vehicle and replaced the wiring harness clips in the rear of the vehicle. The contact received a second notification for NHTSA Campaign Number: 25V572000 (Back Over Prevention); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The vehicle was returned to the dealer, and it was determined that the camera did not need to be replaced. The vehicle was not repaired under NHTSA Campaign Number: 25V572000 (Back Over Prevention); and the failure persisted. The manufacturer was made aware of the issue and referred the contact back to the dealer for assistance. The failure mileage was unknown.

There have been 3 instances within the last year and a half where the rear window of my vehicle (Ford mustang) and the rear window of family member ford mustang both have shattered during the extreme cold possibly due to the heating coils on the window over heating and burning. You can see a burn pattern in the window This is a safety issue due to the window shattering, it sounded as if someone shot my window out the first time it happened my [XXX] son was in the back of the vehicle and I was driving home. The second instance, same vehicle, started the car using the remote starter and it did the same thing. This has not been inspected by my insurance representative, it has been reported in both instances through my insurance and pictures have been taken. There have been no warning signs or even issues, there wiring look like it had been burned, melted INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The contact owns a 2016 Ford Mustang. The contact received notification of NHTSA Campaign Number: 25V614000 (Seat Belts). The contact stated that the driver’s side front seat belt had detached from the frame. There were no warning lights illuminated. The local dealer was contacted and informed the contact that the recall repair would be available in June 2026. The vehicle was not diagnosed or repaired due to parts being on backorder. The manufacturer was not contacted. The failure mileage was approximately 50,000.

At about 75k miles my mustang started misfiring at about 2,500 rpm’s and higher. Turns out it was a blown head gasket. This engine model is prone to what happened to it. Ford should have a recall for these engine and a solution as they’re ticking time bombs. I wish I could drive with the peace of mind of not worrying about it. I couldn’t drive my car for months because of the warranty not even wanting to cover it. The warranty from the used car dealership. Got unlucky.

The driver And passengers door opens while driving

The head gasket in my 2016 mustang eco boost failed. I have 126k miles and coolant is leaking into cylinder 2. I’ve always taken care of the maintenance on a timely matter and no modifications have been done.

2016 Ford Mustang 2.3L Ecoboost Engine. Coolant intrusion into the cylinder. It's a known issue, an engine block design flaw. Ford was replacing the whole engine when those cars were under warranty. There is extensive content online about it and dozens of class actions.

My cars head gasket blew at only 45,000 miles. Replaced my a local well known mechanic for around $3500.00. Now my car at 96,000 miles has blown the head gasket again. I believe the car needs a whole new block. I have seen several lawsuits regarding this and just would love my car running again. This is NOT cheap to fix for me.

On 12/06/2025 I filled the vehicle with gasoline. As I was driving home I noticd a strong odor of gasoline. When I arrived home I parked the car in my carport. A short time later I went outside and noticed that I could still smell gasoline and I looked under the car, which was approximately 3 feet from my house and saw a puddle under it. This could have caused a fire, so I immediately took the car to a repair shop. Approximately one hour later I received a call from the shop informing me that the tank was broken at the top and it would cost approximately $2,600 to replace the tank. The problem was confirmed by Gemba Automotive, Surprise, AZ. I am unaware of whether they have the part available for inspection. There were no warning messages or lights displayed on the driver information system.

From what I can remember its always been an issue with cylinder 3. I was always repaired by Ford Auto Nation of Fort Worth and Auto World Repair 2021 Engine Failure: Confirmed and repaired blown head gasket 2022 Check Engine Light code P303 - Found faulty as well as ignition coil on cylinder 3 2025 Engine Failure: code P303 - Found faulty as well as ignition coil on cylinder 3 Excessive smoke during idle Cracked engine block due to coolant leak through cylinder wall

The contact's daughter owns a 2016 Ford Mustang. The contact stated that the rearview camera was inoperable while reversing. The owner received notification of NHTSA Campaign Number: 25V572000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The vehicle was taken to the dealer, where the contact was informed that the vehicle had passed the recall test, even though the part to do the recall repair was not yet available. Additionally, the contact stated that the rearview camera failure persisted. The vehicle was taken back to the dealer, where the contact was informed that the rearview camera needed to be replaced. The dealer advised the contact that the VIN was not included in a related recall; however, the VIN was included in NHTSA Campaign Number: 25V572000 (Back Over Prevention). The vehicle was not repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the failure. The failure mileage was approximately 86,000.

Display screen went out after first back up, camera recall. Camera is fixed under the recall by the dealership shortly after the display screen was intermittently going out until the screen became completely black.

Component/system: Engine (Coolant intrusion into cylinder 1); Inspection available: Yes; Safety risk: Sudden power loss on road; Reproducibility/Confirmation: Dealer verified coolant in cylinder 1 after engine inspection; Manufacturer, police, insurance representatives or others inspections: No; Warnings/symptoms: Check Engine light turned on, error code P0301, higher than normal engine temperature, low coolant in reservoir, white smoke, rough idle at turning of engine; First appeared: Around 100,000 miles.

Coolant intrusion into the cylinder head. This caused a sudden halt of he vehicle which could have caused an accident and loss of life. The engine coolant overheating temperature warning light came on. Vehicle was inspected by ford dealership and found to have blown head gasket. The car is vat for inspection.

Took car to dealership per recall. Touch screen flickering on and off. Can't depend on back up camera. According to dealer "Recall 22a06a was previously completed on TSB 19-2273. and no other repairs were neede at this time. Note, Sync MyTouch screen is blinking on and off at all times and recommend Diag." they replaced APIN and Screen. According to the repair bill. It was still flickering and replaced FDCIN. Screen no longer flickering. it seems to me this is a safety hazard as it affects the viewing of the back up camera with any accuracy and could cause an accident no matter how careful a person is. It also seems to me that Ford knew extra parts my be needed to rectify the situation they should have been included in the orginal recall

• What failed & is it available for inspection? Air-conditioning system failure. Loss of cabin cooling; dealer recommends compressor replacement (may include related components pending contamination check). Vehicle is at a Ford dealer now; no repairs performed yet. I requested the dealer retain failed parts for inspection. • How was safety put at risk? I live in Las Vegas; ambient temps ~112°F-120 degrees. This is my primary vehicle for transporting my [XXX] and for my work schedule. With no A/C, cabin temps become dangerously high within minutes, creating a heat-related illness risk (child and driver), impaired concentration, and fatigue during necessary trips. • Has the problem been reproduced/confirmed? Yes. An independent shop first advised compressor replacement. A Ford dealer subsequently confirmed loss of cooling and produced an A/C repair estimate after diagnosis. • Inspected by manufacturer/police/insurance? Inspected/diagnosed by an authorized Ford dealer. I opened a Ford Customer Relationship Center case (XXX) and requested goodwill/after-warranty review. No police/insurance inspection. • Warning lamps/messages/symptoms & onset? No warning lights. Symptoms began with weak/intermittent cooling in early August 2025 and progressed to no cold air. Mileage at failure ~87,279. A/C clutch cycles but cabin air remains hot. (Owner context: original owner, [XXX] Vehicle: 2016 Ford Mustang GT 5.0.) INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

My tire is a 255 / 40 ZR 19 model, speed rated 100W. While rotating my tires I noticed catastrophic tread separation on the inner sidewall of the tire. The separation is scattered, not all in one section, and in total covers about 1/4 of the total diameter. The underlying belt package has separated and steel wire is plainly visible at distance. The tire was still holding normal pressure at the time of discovery and there was no indication of the separation from any pressure devices or anything other than visual identification of the issue, which was only possible due to a routine tire rotation. Driving conditions since installation of the tire have been ~85% dry weather at speeds no greater than 85mph. A long haul trip from San Jose, CA to Los Angles, CA (~675 miles round trip) occurred 1.5 weeks prior to discovery.

The coolant over temperature warning light of my 2016 ford mustang ecoboost came on and the engine immediately went on limp mode and I stopped the vehicle and switched off the engine. The vehicle quickly lost power and this created safety concern for other drivers who would have bumped me. I towed the vehicle to the nearest ford dealership for inspection and they found that coolant went into the engine and the coolant bottle was empty. As a result the dealership has said that the engine engine needs to be replaced…. a big shock for me as I have never had any prior issue with this car which is only 59k illegal on the clock. After further research of my own, this seems to be a common issue with ford ecoboost engine before year 2020. What surprises me is that there was no other indication or warning before this incident which could have obstructed me to take precautionary action.

Backup Camera doesn’t work after purchasing a new camera from dealership and new wires. dealership said they didn’t know what was wrong after 3 months of working on car and new parts purchased

The steering wheel has a very distinct wobble. It moves in every direction as if the locking bolt is loose.

Brake Stop Lamps Remain On When I was driving, my car was having throttle/acceleration issues. When I had my foot on the gas, my car would accelerate and the RPMs would rise, but then all of a sudden the acceleration stopped as if I was not applying throttle. I had to constantly take my foot off the gas and reengage for the car to drive home. When I parked my car, I noticed that my brake lights were all on even though my car was turned off & it is draining the battery out. I did some research & found out there is a recall for this issue (22S02) for the 2015 Ford model & Dealership mentioned that recall doesn't apply to my vehicle. So I have to get the repair done by replacing the break light switch & Break pedal bumper assembly with my local Auto zone shop and pay from my pocket.