Ford Mustang 2015 — Problemas reportados

Safety Recall 22S06 – Incomplete/Failed Recall Repair and Refusal of Coverage Under Ford Recall 22S06, my vehicle was brought to an authorized Ford dealership approximately 3 years ago to address the known rear-view camera harness chafing defect. Rather than replacing the damaged component, the dealership performed a temporary patch repair by wrapping the chafed decklid wiring harness in electrical tape. ​This temporary repair has now completely failed. The rear-view camera screen displays a blank black screen or "Camera Unavailable" warning while the vehicle is in reverse, eliminating all rear visual awareness and recreating the precise safety hazard targeted by Recall 22S06. ​I contacted an authorized Ford dealership to have the failed recall harness addressed. The dealership refused to inspect or service the failed recall component unless I agreed to pay an out-of-pocket diagnostic fee. ​I subsequently escalated the issue to Ford Customer Relationship Center. Ford Corporate refused to offer goodwill assistance, clear the diagnostic requirement, or honor the completion of the recall remedy free of charge. The total loss of the rear-view camera image significantly reduces rearward visibility, creating an immediate safety risk of backover crashes involving pedestrians, children, or property. Because the manufacturer’s initial remedy failed and both corporate and dealer levels refuse free-of-charge remediation, the vehicle remains in a non-compliant, unsafe state. I request that the NHTSA Office of Defects Investigation document this failure as an inadequate/incomplete recall remedy under Campaign 22S06 and compel the manufacturer to perform a complete harness replacement at no cost. Thank you

While making a slow turn I heard a popping noise then the steering locked up completely. I shit the car off and started it again to regain steering and get the car home. I used FORSCAn to retrieve codes U0401 and U0415 for the PSCM, both codes have same time frame. This indicates the PSCM lost communication with multiple modules at the same time during a low-speed turn, resulting in loss of power steering assist / steering lock. This is a safety issue as described in Ford Recall 19S26, but my VIN does not show this recall as applicable. Vehicle has not been repaired. Codes have not been cleared and are available for inspection.

Clutch assembly failed, the metal bracket weld cracked/failed resulting in the clutch pedal being inoperable. It's not available for inspection since I had it replaced and the defective assembly disposed of. My safety was at risk since I had extreme difficulty shifting gears on the road. The issue was confirmed at an independent service center - AAMCO of Huntsville, AL. No other entity inspected the part. The vehicle gave me no warning or indication of a problem other than the difficulty with starting and operating it.

I am filing a formal safety complaint regarding a catastrophic Electronic Power Assisted Steering (EPAS) failure and severe electrical short circuit on my 2015 Ford Mustang. This vehicle is exhibiting hard fault code B137F:09 (Steering Wheel Left Switch Pack: Component Failure / Short to Ground or Open). This electronic failure creates an immediate, severe safety hazard that goes entirely outside the scope of normal vehicle wear and tear. While driving, the vehicle's steering wheel pulls and jerks violently on its own, actively fighting my manual steering inputs. Furthermore, this internal electronic short creates a massive parasitic electrical draw that prevents the vehicle's computer modules from entering sleep mode when turned off. This has resulted in the primary vehicle battery draining completely flat and causing the vehicle to completely shut down, stall, or lose total electrical power altogether. A vehicle that forcefully steers itself away from the intended path of travel and suffers total electrical shutdown is a clear, life-threatening safety risk to myself and others on the road. Ford Motor Company is fully aware of this dangerous defect. They previously issued Safety Recall 15S18 for a very specific, limited batch of early-production 2015 Mustangs experiencing identical EPAS failures, replacing their steering gears for free. For the remaining 2015 Mustang owners experiencing the exact same hazardous failure, Ford quietly shifted the issue over to a Technical Service Bulletin (TSB / SSM 51312). By limiting the scope of Recall 15S18 purely due to the financial cost of a universal recall, Ford has left an entire population of 2015 Mustang owners in direct harm's way. Some owners received a free lifetime safety fix, while the rest of us are being forced to pay thousands of dollars out-of-pocket to correct an identical factory electronic defect. I request that the NHTSA immediately open an investigation into Ford's handling of the 2015 Mustang EPAS and more.

The driver-side seat belt retractor on my 2015 Ford Mustang GT Premium has failed. The seat belt retracts back into the retractor housing when released; however, it does not lock when pulled sharply and continues to extend freely. I confirmed this by repeatedly performing a rapid pull test while seated in the vehicle. The failure affects the seat belt restraint system because the belt does not appear to engage its locking mechanism. This could increase the risk of injury in a crash because the seat belt may not properly restrain the occupant during sudden deceleration or impact. The issue was inspected and confirmed by a Ford dealership service department. The dealer diagnosed the driver-side seat belt retractor as failed and recommended replacement of the retractor assembly. The dealer provided an estimated repair cost of approximately $550 plus tax. The vehicle was inspected by Smith Ford in Conway, Arkansas. The vehicle was also inspected for a separate seat belt recall, and the recall inspection passed. The dealer advised that the failed retractor was not related to the recall and would require customer-paid repair. There were no warning lights, messages, or airbag system warnings present when the failure was discovered. The primary symptom was that the seat belt would retract normally but would not lock during a rapid pull test. The exact date the failure first occurred is unknown, but the condition was identified during normal vehicle operation and later confirmed by the dealership.

The contact owns a 2015 Ford Mustang. The contact stated that while reversing, the rear-view camera displayed a black screen. The dealer was made aware of the failure, and the contact was informed that parts needed to be ordered to repair the vehicle. The contact stated the dealer had been contacted several times, and the contact was informed that the parts were unavailable. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The contact later received notification of NHTSA Campaign Number: 25V572000 (Back Over Prevention). The manufacturer was made aware of the failure, and a case was filed. The contact was informed that the parts were available. The failure mileage was approximately 37,000.

My passenger door latch pops open nearly every time I drive on the highway. The latches were previously the subject of Safety Recall 16S30. I had my vehicle inspected by a Ford Dealership. No repairs or work was deemed necessary at that time. In the years since, my door now comes unlatched. Infrequently at first and now with very alarming frequency. Safety Recall 20S30 was issued specifically to address these inspections and recalls being completed ineffectually. Somehow my VIN has been left off of this recall even though it was on the 2016 one. The dealership is trying to charge me nearly $2000 to fix a known safety issue. This seems unreasonable, unfair, and extremely dangerous.

I was driving down the highway with heater on and defrost. All of a sudden I hear a pop and my car started bogging down. I exited the highway to get out of danger, it then had a wrench light ( transmission) pop up and when I parked the car on the access road it started smoking a lot. I turned the vehicle off immediately and when I seen smoke coming from under the hood and into the cab of the car. I lifted the hood after seeing fire in the passenger wheel well. And then in the engine block towards the windshield in the middle of the engine. I am a fire fighter and it appeared to me that the fire was being fed by some kind of substance. Fort Worth Fire department showed up and put the fire out and took a report.

While driving, I attempted to depress my clutch pedal in order to bring my vehicle to a stop. My clutch pedal only went halfway to the floor. I was able to force it down to the floor using a higher than usual amount of force. After bringing my vehicle to a stop I inspected my clutch pedal and found that it had side to side play resulting from a cracked weld where the clutch pedal was welded to a shaft on the clutch/brake pedal assembly. Upon further research online I discovered that other owners of similarly aged mustangs have had identical issues to what happened to me.

The weld that holds the clutch pedal broke causing the clutch pedal to not engage properly. Driving in traffic during a down shift stop almost caused an accident. Which led to not being able to shift gears which left the car unable to drive and left the stranded on the side of the road. The weld that hold the clutch pedal in place is insufficient and weak. While researching this issue I found many instances where this has happened to other drivers.

The contact owns a 2015 Ford Mustang. The contact received notifications of NHTSA Campaign Numbers: 25V572000 (BACK OVER PREVENTION) and 25V614000 (SEAT BELTS). The contact stated that the rearview camera displayed a distorted image while the vehicle was in reverse(R), and occasionally a blank screen was displayed. The message "Rear-view Camera Unavailable - Contact Dealer" was displayed. The contact stated that the failure had obstructed the driver's visibility, which prevented the driver from safely operating the vehicle. The vehicle was taken to the dealer. The dealer inspected the rearview camera and informed the contact that the camera had passed the inspection and the recall repair was not needed. The vehicle was not repaired. The contact stated that the failure persisted. The manufacturer was not made aware of the failure. The failure mileage was unknown.

“Charge system service now” came on the dash, battery lost power after about 10 seconds, screen went black, dash went black, car locked up, opened the hood and the engine was on fire, called 911 who came quickly and put the fire out without the entire car burning, insurance later total losses the car. I don’t know if it was the battery or the engine responsible for the failure, because the flames were on the engine and not the battery, but the incident was triggered by a battery warning. I was on the interstate driving 60mph when the car shut off and everything including my headlights and even hazard lights went black. Not only could I have been struck by a car on the interstate, I could have died in a car fire. Because the car locked up, I couldn’t open the trunk or use any electronics. The door could have just as easily locked and trapped us inside a burning car. The car is on a salvage yard, no attempt to replicate has been made. Progressive insurance, and Columbia fire inspected it and found that it was undetermined. “Charge service system now” was the only warning before the infotainment screen shut down to reduce battery usage. Every light on the dash flashed right before everything on the dash went black and power was lost to the entire vehicle.

With only 32,885 miles, engine light came on due to (P0456) EVAP small leak. Went to an auto shop and Ford dealer for diagnostic scan. Both technicians found that there is a bit of smoke coming out from the top of the fuel tank due to a small stress crack at the port near the canister vent hose as well as a small crack below fuel pressure sensor tube. New fuel tank replacement was recommended as the crack could not be repaired. Cost to fix is $1,400 parts and $1,200 labor. This small crack nears the fuel tank seems to be a major concern for owners as it could increase the risk of vehicle fire and should be a recall by Ford for immediate remedy.

When putting the vehicle into reverse the backup camera displayed an unusable red fuzzy screen. Backup camera was unable to assist in safely reversing and mirrors and parking sensors had to be used

The contact owns a 2015 Ford Mustang. The contact received notification of NHTSA Campaign Number: 25V614000 (SEAT BELTS); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure.

The contact owns a 2015 Ford Mustang. The contact received notifications of NHTSA Campaign Numbers: 25V614000 (Seat Belts) and 25V572000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The dealer was contacted and confirmed that parts were not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact had not experienced a failure.

The contact owns a 2015 Ford Mustang. The contact stated that while driving 35 MPH and attempting to depress the brake pedal, the clutch pedal detached from the brake pedal assembly. Neither an independent mechanic nor a dealer was contacted. The vehicle was not taken to a dealer or independent mechanic to be diagnosed. The vehicle was not repaired; however, the vehicle was in the process of being repaired. The manufacturer was not notified of the failure. The approximate failure mileage was 115,724.

The contact owns a 2015 Ford Mustang. The contact recently purchased the vehicle. The contact became aware that the VIN was included in NHTSA Campaign Number: 20V331000 (LATCHES/LOCKS/LINKAGES). The vehicle was taken to the dealer, who refused to inspect the door latch codes. The contact was informed that it appeared that the recall repair was started; however, it was not completed. The dealer stated that since the remedy was not completed, it could not be finished. The manufacturer was made aware of the issue and informed the contact to request the dealer to inspect and verify if the remedy had been completed. The dealer refused and stated that the software did not allow the dealer to inspect the vehicle. The failure mileage was 78,955.

The contact owns a 2015 Ford Mustang. The contact received notification of NHTSA Campaign Number: 25V572000 (BACK OVER PREVENTION). However, the part to do the recall repair was not yet available. The contact stated that the rearview camera displayed a distorted image while the vehicle was in reverse(R). The contact stated that the failure obstructed the driver's visibility, preventing the safe operation of the vehicle. The contact stated that the rearview camera had not been working properly since the vehicle was purchased. The local dealer was not contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The failure mileage was approximately 30,000.

The contact owns a 2015 Ford Mustang. The contact stated that the back over prevention camera intermittently failed to operate as needed while the vehicle was shifted into reverse(R). The contact stated that the camera image either displayed a blank image or the camera displayed an inaccurate distance between objects. As a result, the contact stated that while reversing into the driveway at approximately 5 MPH, the rearview camera displayed an inaccurate image and the distance between the vehicle and another vehicle parked in the driveway. As a result of the discrepancy, the contact struck the parked vehicle, which damaged the rear quarter panel of his vehicle but there was no damage to the other vehicle. Due to the low impact of the crash, the contact was not injured and an air bag did not deploy. There was no Police report filed. The contact then received notification of NHTSA Campaign Number: 25V572000 (Back Over Prevention); however, the part to do the recall repair was not available. The local dealer was made aware of the issue and confirmed that parts were not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was notified of the failure but offered no assistance. The failure mileage was unknown.

The contact owns a 2015 Ford Mustang. The contact stated that while reversing, the back-over prevention camera screen independently turned off and on. In addition, the error message indicated to contact the dealer for assistance. The contact stated that the failure was persistent. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The contact received notification of NHTSA Campaign Number: 25V572000 (Back Over Prevention); however, the parts for the recall repair were not available. The manufacturer was not made aware of the failure. The failure mileage was approximately 27,000.

The contact owns a 2015 Ford Mustang. The contact stated that while in reverse(R), the rearview camera failed to display an image of the rear of the vehicle, compromising the back over prevention system. No warning lights were illuminated. The vehicle was taken to the dealer, who diagnosed a failure with the rearview camera. The vehicle was repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 25V572000 (Back Over Prevention); and the VIN was included, but parts were not yet available. The manufacturer was notified of the failure, and a case was opened. The failure mileage was 22,000.

The contact owns a 2015 Ford Mustang. The contact received the recall letter related to NHTSA Campaign Number: XXX (Back Over Prevention). While reversing, the camera was flickering. The vehicle was taken to the local dealer, where it was diagnosed, and the dealer informed the contact that the camera needed to be replaced. The vehicle was repaired, but the failure recurred. The contact stated that the back-over prevention camera was flickering and became inoperable. The key fob and button were not working to open the trunk. The contact had to climb through the vehicle to enter the trunk. There were no warning lights illuminated. The vehicle was taken to another local dealer, [XXX] [XXX] ); who confirmed that the repair was not available. The vehicle was not diagnosed or repaired. The manufacturer was contacted and confirmed that the repair was not available. The failure mileage was approximately 75,000. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The evaporator is leaking and apparently is a known issue from ford and they didn't report this. The evaporator core is leaking and it blows hot air for a good amount. It draws a lot of power form the system and drops the rpm below idling. Forcing me to rev a cold engine so that it does not stall out.

The contact owns a 2015 Ford Mustang. The contact received notification of NHTSA Campaign Number: 22V082000 (Back Over Prevention). The vehicle was dropped off at the dealer for service and remained at the dealer for two days. The contact was then informed that the mechanic in charge of servicing the recall was out sick; the dealer was uncertain if the recall repair had been serviced prior to the mechanic's absence. The contact chose to take possession of the vehicle, and the recall was removed from the vehicle. Recently, the contact stated that the trunk failed to open manually or with the key fob. The contact decided to tie a string to the emergency truck release, which was inserted through the back seat to open the trunk. The vehicle was taken to another dealer, where the contact was informed that the wiring to the trunk and backup camera were all connected. The contact was informed that the trunk failure could lead to a rear-view camera failure. The vehicle was not repaired. The manufacturer was notified of the failure but offered no assistance. The contact was then referred to the NHTSA Hotline to report the failure. The failure mileage was 118,000.

Right after picking up my 2015 Ford Mustang from dealer service on July 23, 2025, the hood suddenly flew open while I was driving, completely blocking my view and creating a serious risk of collision. The dealership had performed multiple recalls and a multi-point inspection but did not flag any hood latch issue. The vehicle was released as “safe to drive,” yet this happened immediately after leaving their service. This was an extremely dangerous situation that could have caused a serious accident. The force of the hood flying up also caused major damage to the hood and surrounding components. The dealership took the car back and even offered me a rental, but they are refusing to take responsibility or repair the damage, claiming they are not at fault. I am reporting this because it is a serious safety issue and I want to ensure it is properly investigated to prevent similar incidents. I am also requesting that the dealer or manufacturer repair the damage or reimburse me for the cost to fix it, as this was caused immediately after their service.

The 2015 Mustang has been driven about 62,000 miles. The car has not been driven excessively in the 8 + years my wife and I have owned it. I recently heard a noise from the car. I brought the car to a local reputable repair shop. They determined, that there was a problem with the differential. They took the housing case off and found metal shreds in the case. They feel that a bearing failed caused the complete differential failure. I talked to Ford and they have no open recalls for this and recommended contacting the NHTSA. The car is at the repair shop waiting for parts to repair the differential at a cost of approximately $3,000.

Ford is refusing to repair the rear camera wiring defect. The dealer attempted multiple times and Ford is refusing to replace it, instead the dealer is asking for $1000 dollars.

My vehicle had a recall: Ford recall 22S06 involves 2015-2017 Ford Mustangs due to a potential issue with the rearview camera. The wiring for the rearview camera may be loose or damaged, causing the camera to display a blank or distorted image. This can reduce the driver's visibility behind the vehicle, potentially increasing the risk of a crash. The dealership at Ford Chapman Automobile claims the issue is fixed but they never fixed anything on my backup camera. It was blinking and they said it is normal for this vehicle. My backup camera is not working and they are refusing to fix it. I have contacted Ford but they also refer to the report from the dealership and say according to the dealership the problem is fixed and there is nothing that could do. My car has very limited visibility and this causes problems when backing up.

The contact owns a 2015 Ford Mustang. The contact stated that the brake pedal bumper fractured, and the brake lights illuminated. The contact stated that the failure caused the battery to become drained. The accelerator pedal was stuck and drained the battery. The contact stated that the failure was related to NHTSA Campaign Number: 22V011000 (Service Brakes, Hydraulic). Additionally, the contact resides in North Carolina but had not transferred the New York vehicle registration. The contact called the local dealer and was referred to the manufacturer for assistance. The vehicle was not diagnosed or repaired. The manufacturer was contacted and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 76,000.

See attached document for complaint.

The passenger side door will open by itself. This happened twice within the last month with a passenger in the seat and once with no passenger. The warning lamp will come with an alert to say that the passenger side door is open. This puts the safety of those in the car at risk of falling out, or possibly an accident if the door completely opens. The vehicle has not yet been inspected by anyone. The vehicle is available for inspection upon request.

The contact owns a 2015 Ford Mustang. The contact stated that while closing the trunk, the emblem on the trunk located above the rear license plate detached from the vehicle. The contact stated that the trunk was not slammed, and that the emblem could have fallen off while driving, becoming a possible road hazard. The local dealer was notified of the failure, and the contact was informed that there were no recalls on the vehicle. The manufacturer was also notified of the failure, and the contact was transferred to the NHTSA Hotline with the contact’s knowledge. The vehicle was not repaired. The failure mileage was approximately 24,000.

Weld at clutch pedal assembly broke, causing the clutch pedal to bind. This binding prevents the clutch pedal from fully depressing.

The driver side fills with water during heavy rain. This is not due to a leak in the convertible top or any window seals. The water is coming from below. The water is at risk of causing rust build up, electrical malfunction, and mold growth. The problem has not been reproduced by a dealer or independent service center, every time I bring it up they say they don't cover leaks so I have yet to be able to get it checked out. The vehicle has not been inspected by anyone. There were no warning lamps, messages or other symptoms of the problem prior to the the first appearance. This has happened numerous times since 6/17/2023

The most common engine failure issues are associated with the 2.3L EcoBoost engine, which is prone to coolant leaks causing significant damage to the engine.

When driving and going over a bump the rear shock completely ripped from the frame of the car

I am writing to formally request an investigation into a potential recall issue regarding a heated seat module and module plug on my vehicle. Below are the details of my vehicle for your reference: * Make/Model: 2015 Ford Mustang Ecoboost * VIN (Vehicle Identification Number): [XXX] * Mileage: 183,367 I have encountered a burning/melted plastic smell along with smoke coming from my heated/cooled seat module box while operating the vehicle. This issue has impacted safety, and reduced functionality. I have contacted the dealership, and had the part inspected but the issue persists. Upon reviewing similar concerns online and through forums, I noticed other owners reporting comparable problems, starting with many different 2015-2020 ford model vehicles, which leads me to believe this may be a widespread issue. I respectfully request that Ford initiate an investigation to determine if this problem warrants a recall. I also ask for guidance on how to address this issue in the interim to ensure the continued safety of myself and others on the road. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Heated and cooled front seats stopped working. On inspecting the connector plug it is scorched or burned where the ground plug is located.

i was driving on a highway and experienced a total failure of my electrical system which completely shut down with in 15 seconds i lost control of the car as i could not even move the wheel, subsequently T-boned by another car iwhich could not stop fast enough suffering total loss of my car of note prior to the accident (Sunday AM) on friday I had a battery replaced @ Firestone, see reciept attached that was the last repair for the care