Ford Fusion 2015 — Problemas reportados

Reoccuring headlamp outages. Requiring expensive repair because the front bumper must be remvoed to replace headlamps. This has now occured on more than one occasion following replacement of bulbs.

The contact owns a 2015 Ford Fusion. The contact stated that while reversing, the rear-view camera became inoperable. The dealer was contacted by phone and made aware of the failure. The contact was informed the repair was not covered under recall. The contact referenced an unknown recall; however, the VIN was not associated with a recall associated with the failure. The failure mileage was approximately 120,000.

Year/Make/Model: 2015 Ford Fusion Engine Type: 1.5L EcoBoost 4-Cylinder Description of Safety Flaw and Incident: My vehicle is experiencing severe overheating and internal engine fluid loss due to the widely documented Ford EcoBoost coolant intrusion defect. The vehicle routinely runs hot, losing coolant rapidly with no external signs of a visible hose or radiator leak as well as failure of the brake lighting stop bumper and purge valve connecting to the gasline after fueling. This issue causes the vehicle to rapidly overheat while in motion, forcing sudden loss of engine power (limp mode) during highway driving. Car not properly cranking after fueling and brake light continuously being on even when brakes not being pressed. This unexpected drop in speed creates an immediate crash hazard for myself and surrounding traffic. Coolant entering the combustion chamber also fouls the spark plugs, causing severe engine stalling, rough idling, and misfires. I've spent several dollars fixing these malfunctions that have continuously persist. Ford Motor Company has historically been aware of this structural defect involving coolant leaking across the cylinder bore walls, yet failed to issue a comprehensive safety recall for 2015 models. I am filing this complaint to urge the NHTSA to open a formal defect investigation and mandate a safety recall, as this component failure leaves drivers stranded in hazardous traffic situations.

Recall 22S43 failed less than 5 months after completion, causing total vehicle immobilization in reverse on a live roadway.

The 2015 ford fusion are very known for this issue with coolant lost and more recently I was driving and a warning popped up saying my coolant was over temps so I pulled over and turned the car off next thing you know my coolant was gone and I just filled it up. To make it even worse my mechanic told me it’s a known issue and ford doesn’t even cover it because it isn’t a recall

When driving off and on the power steering will go out and different warning lights will come on including “hill parking assist is off”.

I was involved in a serious rollover crash in which my vehicle rolled approximately two times. During the crash, I struck my head and suffered a deep laceration that required five stitches, along with a concussion. I also experienced numbness in my head for several days afterward. The crash caused extensive damage to my vehicle, which was ultimately determined to be a total loss. Multiple windows shattered, the windshield was severely damaged and pushed inward, and there was significant damage to the roof and body of the vehicle. Despite the severity of the rollover and the amount of damage to the vehicle, none of the airbags deployed at any point during the crash. I am concerned that the airbag system may not have functioned properly and that the lack of airbag deployment may have contributed to the severity of my injuries. As a result of the injuries I sustained, I have also been unable to return to work and have been placed on medical leave while I recover. This has affected both my ability to work and my day-to-day functioning following the crash.

The contact owns a 2015 Ford Fusion. The contact stated that there was an abnormal popping sound coming from the vehicle while pulling out of the driveway and driving approximately 10 MPH. The contact stated that the steering wheel seized and locked up. The power steering, Hill Assist, and brake warning lights were illuminated. The contact associated the failure with NHTSA Campaign Number: 19V632000 (Steering). The vehicle was taken to the local dealer, where it was diagnosed that the steering gear had failed and the bolts were corroded. The manufacturer was contacted and confirmed that recalls were VIN-specific, and no assistance was provided. The failure mileage was approximately 177,000.

I am reporting a potential safety defect involving an Evenflo Revolve360 child restraint. Manufacturer: Evenflo Product: Revolve360 Model: CS360212464 Manufactured: September 26, 2025 Purchased: XXX from Target The seat was used rear-facing by my [XXX] daughter, who weighs approximately 27 pounds. After only about four months of normal use, I discovered significant localized fraying/tearing of the harness webbing. I have photographs documenting the damage. The damage appears concentrated in a specific area of the harness webbing near where it passes through/contacts components of the seat. I do not see corresponding damage to the surrounding fabric, foam, plastic, metal structure, or other visible areas that would readily indicate an environmental cause. I contacted Evenflo and provided photographs. Evenflo stated that the damage “appears to be related to external environmental factors” and that the components contacting the strap are smooth and rounded. However, Evenflo did not identify what specific environmental factor caused the damage or what physical evidence supports that conclusion. Evenflo also advised that the seat could be used in booster mode if my child met the requirements. This is not an applicable solution because my daughter is only [XXX] old, [XXX] pounds, and still rear-facing. My concern is product safety: a critical harness component experienced substantial deterioration after approximately four months of use. I am requesting that NHTSA record this as a child-restraint safety complaint and evaluate whether this harness deterioration could represent a potential safety defect or pattern involving the Revolve360. I can provide photographs, proof of purchase, product labels, Evenflo correspondence, and the physical seat if needed. Sincerely, [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The contact owns a 2015 Ford Fusion. The contact stated that while driving 45 MPH, the messages "Loss of Traction Control" and "Advancetrac Off" were displayed, and the vehicle lost power steering functionality. The contact safely pulled over to the side of the road. The vehicle was towed to the dealer, where it was diagnosed and determined that the steering gear motor had failed and needed replacement. The vehicle was not repaired. The contact associated the failure with NHTSA Campaign Numbers: 15V250000 (Steering) and 19V632000 (Steering). The contact stated that the vehicle was previously repaired under NHTSA Campaign Number: 15V250000 (Steering); however, the recall repair failed to prevent the failure. The manufacturer was notified of the failure, but no assistance was provided. The failure mileage was approximately 177,000.

Rear view camera goes out or says not available.

BACK UP CAMERA GLITCHES OFF AND ON - WILL WORK AND THEN CUTS OFF WHILE BACKING UP REPEATLY - BLUE SCREEN

I have a coolant intrusion into the engine and blew my engine in the middle of driving down the highway. No signs, no warning. Lost control, ended up on side of road. Had husband pull it the rest of the way home.

IT FEEL AS IF THERE IS NO POWER STEERING. RAN CODE REPLACED THE Steering wheel angle sensor AND THAT DIDN’T SOLVE THE PROBLEM. I CANNOT STAIR THE STEERING WHEEL GETS LOCKED UP ..

Engine warning display came on with "cylinder over temperature" immediately after temperature gauge went from normal (slightly under 1/2 way) to "Hot" immediately. Shut off engine - opened hood, coolant was noticed on passenger side just below coolant bottle. After waiting a little bit the tempature on the gauge hadn't dropped any & the radiator was cool to the touch. The day before washer fluid was added, while there the other levels were checked after sitting all night, the coolant was showing within the marked operating zone. Ended up calling for a tow truck.

UNKNOWN: Left rear door latch is not working, door keeps open after trying to closed it. Safety issue is door opens by accident during driving!

I was driving down the road. And front wheels stopped working suddenly. It’s better that I was on streets. Otherwise I could have met with an accident. My mechanic told me that steering rack had gone. I never get any recall for that. I had driven 1400 miles till now.

My drivers side door would not latch due to what I assume is issue that was recalled on similar vehicles

I bought the 2015 ford fusion for my son as a graduation present as he headed off to college on his own. The car started misfiring upon cold start for about 5-10 seconds. Eventually the car started misfiring while driving. He frequently had to pull over on the side of the road while driving to make it to his destination. I had him take the car to a ford dealership to be inspected. To my surprise, Ford Parks of Wesley Chapel told me that the 2015 Ford Fusion 1.5L ecoboost has a known issue with coolant leaking into the engine causing misfiring and eventually engine failure. They offered no assistance in fixing the problem. They told me the cost to replace the engine was over 13,000.00.

The contact owns a 2015 Ford Fusion. The contact stated while reversing, the rear-view camera displayed a brief image, a blue image or a black image with the message " Rearview Camera Unavailable". The contact stated while reversing at an undisclosed speed, the failure recurred, causing the rear-end to strike a pole. The contact sustained a whiplash, and minor neck pain but did not seek medical assistance. The trunk of the vehicle sustained a dent. Upon looking up recall information on the Ford website, the contact became aware that the VIN was included in Customer Satisfaction Program Number: 25N17 (Rear-view Camera Replacement if Required after Dealer Evaluation). The dealer was contacted and scheduled a repair appointment; however, the trunk repair was not covered under the recall. The manufacturer was contacted and denied liability for collateral damage. The failure mileage was unknown.

The contact owns a 2015 Ford Fusion. The contact stated that the vehicle was experiencing excessive coolant consumption, causing the low coolant pressure warning light to illuminate prematurely. The vehicle was taken to an independent mechanic, where it was diagnosed with coolant intrusion in the combustion. The contact was informed that the head gasket or the engine needed to be replaced immediately to prevent further issues. Additionally, the contact was informed that the failure was due to a faulty engine design. The vehicle was not yet repaired. The manufacturer was notified of the failure and informed the contact that although the model year was affected, the vehicle was not covered. The failure mileage was approximately 91,000.

While driving, the car’s acceleration started to slow down an no matter how much I pressed the gas, it wouldn’t go. I was only able to do 5 miles an hour. It was a loud noise like it was reving up, but wasn’t going anywhere. There was no warning lights. I did not have any issues previously nor had any repairs made. I took it to the auto repair shop the same day and they had confirmed it was the transmission.

I own a 2015 Ford Fusion SE. I bought it used when it only had 47,000 miles on it. Over the course of time since buying it in DEC 2022 until now, it has had low coolant that I have had to address but no visible leaks. Current mileage now is 87,100 and just recently the coolant was low again and the check engine light came on for DTC P0301 -Cylinder 1 misfiring. It has had rough start ups, rough idle, decreased acceleration, and poor fuel efficiency. I have found the problem to be Coolant Intrusion – Engine Defect Concern “Coolant intrusion” is a known engine design defect in which coolant leaks into the cylinders, leading to internal damage, misfires, and eventual engine failure. After researching it I found that many other people have had the very same issue with no help from Ford. This should be a recall as this is an internal issue with the short block and something that should have been disclosed before purchasing this model/engine. The only repair that will fix the core of the issue is replacing the entire short block which costs thousands of dollars, way more than the cost of the entire vehicle at this point. Without fixing the issue, the engine will fail. Again, this should be something Ford should pay to repair, not any customer who came into this blind.

I am reporting a serious and ongoing safety issue involving my 2015 Ford Fusion. The vehicle experiences intermittent power steering failure while driving. The steering assist will suddenly disengage and re-engage without warning, making the vehicle extremely difficult to control. This condition becomes even more dangerous in wet weather, where the vehicle is sometimes nearly undriveable. Additionally, I am now experiencing a popping noise in the steering wheel. This raises concern of a possible mechanical failure consistent with known recalls involving steering wheel bolt defects that could result in the steering wheel detaching. These issues are consistent with known recalls, including: - Power Steering Failure Recall (15V340000) - Steering Wheel Bolt Recall (18V167000 / 18S08) Despite these known safety defects, Ford has refused to repair the issue, stating that the recall has expired. This presents a serious safety hazard, including risk of loss of steering control, crash, injury, or death. I am requesting immediate investigation and enforcement of manufacturer responsibility for this safety-related defect.

While driving at 30MPH, vehicle lost power without any notice/warnings. Had the vehicle towed to dealer who misdiagnosed as transmission problem (quoted $8000 to swap). Had a second opinion and indeed it was the dreaded coolant intrusion in the engine, catalytic convertor which cause the loss of acceleration and the transmission was completely fine. This is a ridiculously common issue with the 1.5L engine and Ford has not offered any support other than "oh well" mentality. Prior to this, car lost coolant, I had to top it off every couple days, blew with smoke, sweet smell, all in line with coolant intrusion. Had the lines checked and repaired as recommended but about 6 months later this happened.

Coolant Intrusion in the Block Led to white smoke coming out of the exhaust thick enough that I couldn't see as I tried to back out of the road.

My steering gear motor attachment bolts have fractured due to severe corrosion, which is the exact defect described in Safety Recall 19S26. This physical failure was confirmed by a Ford dealership technician on 1/11/2024. The technician documented the fractured bolts and recommended a full steering gear replacement. Despite this, Ford is denying the recall repair because this specific VIN was not included on the original mailing list. The vehicle is now undrivable due to a total loss of power steering assist. Before it failed completely, the car was making whining and grinding noises during low-speed turns. This failure occurred in Illinois, which is a high-corrosion 'Salt Belt' state specifically covered by the 19S26 bulletin. By denying this safety repair, Ford is forcing an unsafe vehicle to remain on the road or operate with manual steering, which is a major crash risk. The failure was physically confirmed and documented by a Ford dealer. I want to note that while the previous recall 18S08 for the steering wheel bolt was performed, that was an unrelated interior part and did not prevent this exterior motor bolt failure. I am requesting that the NHTSA investigate why a vehicle with a confirmed 19S26 failure in a covered state is being denied the mandated safety remedy.

My steering wheel came detached as I was driving. Forest is refusing to pay to have it towed to the dealership to be fixed. I do not understand why I have to pay $160 for a tow that was a defect of ford. At that point, it is no longer a free repair

The rear camera intermittently fails or displays a distorted image. I reported the issue to our local Ford dealership in April/May 2022, but at that time the necessary replacement parts were not available or in service. This was probably related to the various Covid 19 pandemic parts supply issues. Yesterday, while the car was being backed out of our garage, a young child was playing in the driveway directly in the vehicle’s rear blind spot. As usual, the camera was not functioning. Fortunately, an adult supervising the child noticed the situation and intervened, preventing what could have been a terrible tragedy. We have seen news reports about recalls addressing rear camera issues in many Ford vehicles—yet not for our 2015 Ford Fusion. How many serious incidents must occur before Ford takes action to correct this problem?

Internal transmission bearing know for the TSB 19-2391. There was no threat to my safety or others. Yes the problem has been confirm with the dealer. The components has been inspected by an authorized Ford Dealer, Shaker Ford in Watertown, CT. There were nothing other than a humming noise coming from the transmission.

The rear backup camera screen is black or flickers, and sometimes shows an error message like "Camera not available." Ford just issued another recall for rear cameras for this issue, but deliberately excluded Ford Fusion vehicles. They need to include ASAP as this is a known, dangerous issue that can cause an accident.

Rear view camera is not functioning. The screen goes black or a message is show to contact dealership. No sensors work nor a view of what is behind me. There are times I almost hit people or other vehicles. There are recalls for other vehicles but not my vehicle. There was no inspection but dealership will not fix it. Itsstarted 2 years ago out of no where. Please help!

Rear backup camera goes completely blank, shows a reversed imaged, or just an error code. Not part of the large recall in 2025. It should have been

Was driving g on the freeway and car began shaking about 1mile later rhe car would not go past 10 miles an hr without making a loud noise everything was upkept with my car ontop of all recalls and now I have a car that I had to finish paying off without being able to drive it for almost 2 years and can't seem to fund a solution on either the dealer fixing the power train or giving me a refund

The contact owns a 2015 Ford Fusion. The contact stated that while driving at an undisclosed speed, the steering wheel failed to turn in the intended direction. In addition, the contact heard an abnormally loud bang. The power steering failure warning light was illuminated. The vehicle was driven to the residence. The contact diagnosed the vehicle with rack and pinion failure and detached bolts. The contact stated that the bolts were corroded, and the rack and pinion gear had detached. The contact stated that the rack and pinion needed to be replaced. The vehicle was not repaired. The contact referenced NHTSA Campaign Number: 19V632000 (Steering); however, the VIN was not associated with the recall. The manufacturer was made aware of the failure, and a case was filed. The failure mileage was approximately 146,000.

On 2/4/26, I experienced a slight skip while driving, But did not continue. The very next morning while in reverse, A winding sound started. Put car in drive pulled out onto main road, drove fine, not even half a mile. Stopped at sign, pulled out onto main road a main road, and car would not go, would not go in gear at all. No one was hurt, but received a few horn honks. Made it to side of road, put the car in sport/manual mode, did not help. Manage to make it about a mile up the road where I was able to safely park it in a parking lot. The check engine symbol came on a couple of weeks prior, but went away after a day. Did not come back on until this particular day 2/5/26. Nothing, no problems leading up to this. Conveniently the extended warranty went out on car 4k miles ago! And the dealership is not interested in helping me out at all. I had to have it towed to an independent shop, to get checked out, due to the dealership being booked 2 months out! I now have a car that I have only had for 1 year! With a blown transmission that I have to make payments on and can not drive!! There are no recalls, but there is a manufacturer issue, that we do not get notified about by mail or by email..? I read another complaint about this same thing, guy also making payments on a car he can not drive!!! This is ridiculous!! And heartbreaking if I can not get help with this! And you can bet the dealership will receive a less than favorable review!

Brakes, emergency brake, brake switchs. Backup camera turns black while backing up. And yes it’s available for inspection. Car keeps braking and jerking in the other lane by itself. Emergency brake kept coming on by itself randomly. Also I almost hit someone when my back up camera went black. Yes the problem have been confirmed by a dealer or independent service center. Yes it have been inspected manufactures police and insurance representatives. Yes ever single light came on. Advanctrac light. Brake light, emergency break light, abs light and traction control light and tpms and airbags light.

My rear reverse camera has not been working properly. Sometimes the screen is completely black, sometimes the screen has lines in it , sometimes the camera acts like it is moving. It is very disturbing and dangerous. This is not weather related because it happens when it's sunny or raining. I can go a couple of days with out any issues and then randomly it has these issues. This has been going on for a while now so there isn't a particular day. This started happening early last year 2025

My 2015 Ford fusion 1.5 L engine has had problems since 2022. I have been adding antifreeze, changed spark plugs many times, flushed my antifreeze and the vehicle overheats and has had to be towed twice changed out thermostat, spark plugs, coil pack, two times for misfiring coolant housing with no success. Called in a complaint to Ford Motor Co. and they are unwilling to help. They said they put out a bulletin however this does not fix the problem of needing a new engine. I am stuck making payments on a car I cannot drive. My mechanic says it needs a new engine. Never realizing there was a bulletin or a coolant intrusion problem with this engine.

My 2015 Ford Fusion back over prevention camera system, is no longer working. I only get the black screen with error message "Camera is unavailable. Contact dealership". Which is creating a safety issue, while the vehicle is backing up. Reference Recall Number 25SA9 as many other ford products have the same issue. Many 2015 Ford models are covered under this recall. However, my fusion is not, because the recall only states 2016. My camera was troubleshot by a certified mechanic and was deemed a faulty camera by testing it with a different camera, and the system started working properly again.