Ford Fusion Energi Plug-in 2017 — Problemas relatados

The automatic transmission failed at approximately 59,000 miles. The vehicle was delivered to an authorized Ford dealership on 09/04/2025 for warranty repair. The transmission was replaced. The vehicle remained at that dealership approximately eight months and was returned to me on or about 05/01/2026. After return, a grinding and clunking noise was present when accelerating, turning, braking and going over bumps. A power steering line failed within days of return and emitted smoke from the front of the vehicle while driving. A "Shift System Fault" message began appearing when shifting into reverse and continues to appear intermittently. The same dealership performed three further repair visits. Their repair orders document multiple loose bolts holding the transmission mount to the transmission, an improperly installed exhaust, and a loose right hand CV shaft nut. On 08/14/2026 I took the vehicle to a second, unaffiliated authorized Ford dealership for an independent inspection. On a lift they found all four subframe bolts loose, the right front subframe bolt not fully seated and cross threaded so that it could not be tightened further, and the four smaller rear subframe bolts missing entirely. They also documented that no one-time-use fasteners had been billed on the original transmission repair. They tightened the loose bolts, replaced the cross threaded bolt, installed the four missing bolts, and confirmed by road test that the noise was eliminated. The subframe carries the engine, transmission and front suspension. The vehicle was driven approximately 1,700 miles over roughly three months, including highway driving, in this condition before the loose and missing fasteners were found. Repair orders from both dealerships are available for inspection.

We purchased this 2017 Ford Fusion 1.5L EcoBoost in August 2022 at 48,968 miles. At 55,940 miles, the vehicle developed a documented coolant leak requiring water-pump replacement. At approximately 75,520 miles, the coolant level was again documented as requiring attention. At approximately 84,189 miles, the vehicle experienced low coolant, low oil, white/gray smoke and rough running. Manteca Ford identified Ford TSB 22-2322 and ultimately performed a major short-block replacement. Despite this major engine repair, mechanical and drivability problems continued. At approximately 101,375 miles, we returned the vehicle to Manteca Ford specifically for loss of power and hesitation. The Ford technician verified a “noticeable loss of power” and lack of full boost. Manteca Ford diagnosed and replaced the turbocharger. The problem was not resolved. Only approximately 205 miles later, at 101,580 miles, the vehicle returned to Manteca Ford because it was still hesitating during acceleration. Manteca Ford then identified DTCs P0729, P07AA, P2703 and P2704 and documented “TRANSMISSION INTERNAL MECHANICAL FAULTS,” including an incorrect sixth-gear ratio and friction-element faults. The dealer recommended replacement or teardown of the transmission. We are extremely concerned about the safety implications of this history. Loss of power and hesitation during acceleration can create a serious hazard when merging onto a highway, entering or crossing traffic, or attempting to accelerate to avoid a collision. This vehicle has experienced repeated engine/powertrain problems despite major repairs, and we are concerned the transmission condition may have been developing during the earlier loss-of-power/hesitation complaints. We request that NHTSA evaluate this history for a potential safety-related defect or broader pattern.

I was driving my 2017 Ford Fusion Platinum on my way home and the wrench light came on and said check manual when i looked in my app the only thing that was in the maintenance was my 90k maintenance . my car is driving fine no RPM jumping no smoking no burning smell no shaking nothing ( the wrench light was off when i cranked it to take my daughter to work Saturday morning ) well Saturday on my way home from bring my daughter to work my check engine light came on still my car is driving fine when i looked in my Ford App at the check engine light warning which was these two warnings The transmission control system has detected the transmission torque converter clutch is not operating as expected. Additional alerts that may provide additional information may accompany this alert .A reduction in vehicle fuel economy may also occur when the fault is present. The transmission control module has detected that the torque converter clutch failed to apply. This system failsafe logic disables the torque converter clutch when this condition is present. This results in a higher than normal engine RPM's during higher vehicle cruising speeds and reduced fuel economy. now my car is still driving fine. i took it to auto zone to put the computer on it and it read this code P0741 which gives this Torque Converter Clutch Circuit Performance or Stuck Off, which indicates that the vehicle's computer commanded the torque converter clutch to lock up, but it is failing to do so. i took it to our ford dealer ship and he stated oh yes you need a whole new transmission which is 7200$ do you want to pay now .... Im shocked that my car would need a new transmission... i have seen recalls for Torque Converter for the fusion .. but my vin is not showing this recall is there anyone else experiencing this

The transmission shifter cable bushing on my 2017 Ford Fusion has failed and completely disconnected from the transmission housing on two separate occasions.When this happens, the gear shifter inside the cabin operates freely, but the transmission fails to engage the selected gear. The vehicle shows it is in "Park" on the dash, but the actual transmission remains stuck in Drive or Reverse. This creates an immediate and severe rollaway risk and unintended vehicle movement, as the vehicle cannot be safely secured. Ford previously issued Safety Recall 22S43 for millions of 2013–2016 Fusions for this exact identical defect (degraded Hytrel 4556 shifter bushings). Despite utilizing the same design and experiencing identical, dangerous failures, the 2017 model year was excluded. The NHTSA needs to investigate and force Ford to expand Recall 22S43 to include the 2017 model year before an injury occurs.

Orange wrench light came on dash with see manual ( symbol represents powertrain malfunction). Car lost power and started jerky shifting between second and third gear. We limped the car home and parked until we could get an appointment at the dealership for service. Took it to dealership. They found the powertrain maintenance light wasn't on and no current or historical codes present. Dealership road tested vehicle and verified delayed harsh shifting between 2-3 gears with no codes present. Dealership states most likely has an internal failure starting in the forward, direct or intermediate clutch. Transmission would have to be torn down to diagnose cause. They recommend replacing the transmission as being more cost effective. Transmission has approximately 145000 miles (engine was replaced under 36000 miles due to head gasket failure- replace under warranty as manufuring defect found at a scheduled oil change) so odometer only shows 117000 miles. This car was purchased new and we purchased the extended warranty and service package. It has been consistently serviced on schedule by the dealership.

I am submitting this complaint regarding a serious engine failure and safety issue involving my 2017 Ford Fusion equipped with the 1.5L EcoBoost engine. At approximately 79,000 miles, my vehicle experienced a coolant intrusion failure. While driving, the engine suddenly stalled in the middle of an intersection, leaving me stranded in traffic and at risk of being rear-ended by approaching vehicles. I was able to restart the vehicle and move out of the intersection, but the exhaust then produced a very large, thick cloud of white smoke. The amount of smoke could have significantly reduced visibility for other drivers and created an additional safety hazard. I took the vehicle to a Ford dealership, where I was told the engine had coolant intrusion and needed to be replaced. I was also told this is a common problem with Ford EcoBoost engines, including the 1.5L, 2.0L, and 2.3L engines. My concern is not only the cost of the repair, but the serious safety risk. Coolant intrusion can cause misfires, excessive white smoke, engine damage, and eventual engine failure. A sudden loss of power while driving can create a serious crash hazard, as happened to me. I am concerned Ford has known about this recurring problem for years yet has continued using these engines in vehicles such as the Fusion, Escape, and Lincoln MKZ without adequately addressing the issue. I request that NHTSA investigate coolant intrusion affecting Ford EcoBoost engines and determine whether a safety defect exists that warrants a recall. I also believe affected owners should receive reimbursement for engine replacement costs when the failure is caused by this defect. My experience demonstrates that this is more than a normal maintenance issue. An engine that can suddenly stall in traffic and produce a large cloud of white smoke without warning poses a significant safety risk to vehicle occupants and other motorists.

The contact owns a 2017 Ford Fusion. The contact stated that while driving 60 MPH, the accelerator pedal was depressed; however, the vehicle failed to accelerate as intended. The vehicle lost motive power, and the RPM became elevated. In addition, the contact became aware of an abnormal odor. The contact referenced an unknown recall; however, the VIN was not associated with a recall associated with the failure. The failure mileage was approximately 150,000.

I lost power while on the Freeway any indicators flashed: "see manual", "pre-collision assist not available", "service advance track", "downhill assist not available", the check engine light was on. It seems that when to limp mode. I took it to the Ford fusion dealer so they could check the car. They run into test and found that the transmission or motor has failed. I check and found that on that year make and model some cars were affected and it was a recall for that. This is the recall If the torque converter weld studs fail, the torque converter will not be connected to the engine flexplate and the vehicle will lose the ability to move, increasing the risk of a crash.

2017 Ford Fusion. Transmission replaced February 2026 at 98,175 miles by independent repair facility. Check engine light illuminated immediately following replacement and has remained on continuously since. Autozone scan showed emissions-related code only. On August 28, 2026 at approximately 120,064 miles, orange wrench light and "See Manual" message appeared moments after hot restart. Acceleration became heavy and hesitant. Drove approximately 70 miles home via I-15; heavy traffic required engine shutdown at multiple stops. Following morning, wrench light was no longer illuminated but hesitation persisted. Using manual paddle shift to select 5th gear improved drivability. Replacement transmission accumulated approximately 22,000 miles over 6 months. Ford Motor Company has issued multiple recalls for 2013-2016 model year Fusions involving identical transmission, shifter cable bushing, and torque converter defects, but 2017 model year vehicles with identical 6F35 transmissions and failure symptoms have been excluded from all campaigns. No crash, fire, or injury occurred.

Flexplate cracked 5 months ago, and now it has cracked again. This is due to troqeu converting failure and faulty transmission mounts.

If i do not run my car for atleast 10 minutes before driving, my gas tank will start making a loud horn sound, and when this happens and i go to slow down, the car will shut off. Mechanics say there’s an issue with the purge valve and the charcoal filter. I’ve already had this issue fixed three times and it comes back less than a week prior to service

I am reporting a serious recurring safety concern involving a 2017 Ford Fusion SE with a 1.5L EcoBoost engine. The vehicle was purchased used in August 2022 with approximately 50,000 miles. Within months, significant coolant and engine problems began. In February 2023, at approximately 55,940 miles, the vehicle developed a coolant leak. A pressure test confirmed the water pump was leaking and it was replaced. At approximately 84,189 miles, the vehicle experienced white/gray exhaust smoke, coolant loss, very low oil, and rough-running symptoms. The servicing Ford dealership referenced Ford Technical Service Bulletin (TSB) 22-2322 in connection with the diagnosis and ultimately replaced the engine short block. Despite this major engine repair, the problems continued. The vehicle subsequently experienced additional smoking, hesitation and loss of power and required replacement of the turbocharger. The vehicle was returned again because it continued to smoke and required additional repairs. I am concerned this is a recurring engine defect rather than normal wear and tear. The repeated engine/coolant failures, smoking, hesitation and loss of power create a serious safety concern because the vehicle may unexpectedly lose power or experience engine failure while being driven. Ford has been notified of the repeated failures but declined further relief based primarily on the vehicle's current age, mileage and expired warranty. This ignores that the problems began years earlier at substantially lower mileage and that major repairs failed to permanently correct the condition. I request that NHTSA investigate whether the 1.5L EcoBoost engine in this and similarly equipped Ford vehicles has a safety-related defect involving coolant intrusion, engine failure and loss of power. The vehicle is currently at approximately 101,000 miles, but the documented problems began at 55,940 miles and continued despite major repairs.

See attached document for complaint.

I was coming home from work and when I tried to shift the gear from drive to park it was stuck on drive and Neutral I contacted the car dealer and they said ford has had this issue that it was a recall on it so I researched and found out that Ford issued major safety recalls (Recall 22S43 and 18S20) for 2017 Ford Fusions regarding a degraded transmission shifter cable bushing. This defect can cause the shifter cable to detach. Consequently, the car may roll away unexpectedly because the transmission isn't actually in Park, even though the shifter says it is.Recall DetailsThe Problem: The underhood shift cable bushing can degrade and fail over time.The Remedy: Ford dealers will replace the transmission shifter cable bushing and add a protective cap over it free of charge (parts and labor). It my VIN# was not coming up as a recall and this is an ongoing issue for this car and I would like to get this resolved as soon as possible with ford recall please thank you

The vehicle in question has the coolant intrusion into cylinders 2 and 3 with rough idle on startup, P0300, P0302, P0303, and white smoke on startup. The vehicle now has 111339 miles on it and the out of pocket cost is more than what the vehicle blue books for in excellent condition. TSB 22-2134 speaks to all the issue and what the repair is. If this is a known issue then I feel this should be a vehicle recall by Ford due to the costly repair.

I experienced an issue identical to safety recall 22S02. Rear brake light remains on due to a broken Brakelight stop bumper. Dealership did not offer to fix at no charge.

What component or system failed or malfunctioned, and is it available for inspection upon request? Driver's side selt belt does not latch all the time. Yes can be inspected. How was your safety or the safety of others put at risk? If the seat fails, injury can occur in a crash Has the problem been reproduced or confirmed by a dealer or independent service center? Appointment is July 18 Has the vehicle or component been inspected by the manufacturer, police, insurance representatives or others? no Were there any warning lamps, messages or other symptoms of the problem prior to the failure, and when did they first appear? no

Good Aftrrnoon and I hope all is well. My cars check engine light is on and the dealer states it’s the cannister purge valve. I showed them that there is a recall (PART 573 safety recall - NHTSA Recall #26V369) but they will not accept it because it’s not showing my car needing it to be changed on the NHTSA website. They are saying it will cost $1995.00 to fix the issue. This is stopping me from obtaining an inspection sticker and I’ve received tickets. Can you confirm that my vehicle is part of this recall.

ENGINE HAS COOLANT INTRUSIONAND IS MISFIRING. Engine light came on. The coolant system found pressure to be dropping significantly. Removed spark plugs and inspected cylinder bores using borescope. Verified coolant is leaking into cylinder 2 and needed to replace the engine at Ourisman Ford in Manassas VA. on July 11, 2026.

On 7/8/2026, the vehicle became undriveable. Placing the vehicle in reverse on the shidfter dial using registered a conflicting direction on the dashboard indicator. The vehicle was towed to a dealership and the repair consisted of replacing the shift cable bushing. This was the same fix required in recalls 18S20 & 22V413. On 7/9/2026 the issue was verified by a Ford dealership tech. I was advised that the protective cap is now contained in the repair kit with the shift cable bushing. A brief fleeting warning on the screen indicated a "Shift Fault - See Manual" or words to that effect. The manual only seemed to reference a "Steering Fault" Ford HQ was notified - Reference No: CXH-08533100

The door entry control numbers are on all the time now which will cause the battery to drain if the car is not driven daily. It says that water from a car wash or rain has gotten in behind the door control panel.

I am the owner of a 2017 Ford Fusion with 61,000 miles on the odometer. Please note that I have always taken good care of my car, having it serviced promptly when required. In recent weeks, I have had to replace my complete steering rack (cost $4,500) and two weeks later, my 1.7-liter Ecoboost engine due to a coolant leak into the number two cylinder at a cost of $6,700. Ford has known about both problems for years and they have resulted in both class action and small claims suits against the company. Regarding the engine, Ford issued Customer Satisfaction Program 21N12, Technical Service Bulletin TSB 22-2134 and Customer Satisfaction Program 19B37 - Supplement #4 to replace the car's engine short block. This covered cars for 7 years of service or 84,000 miles - with, as quoted in the Ford memo sent to dealers on June 9, 2022, "coverage automatically extended to subsequent owners," for presumably the life of the car. Since this is clearly a manufacturing error (as Ford admits in its June 9, 2022 memo to dealers) and not due to negligence on my part, I should be reimbursed for my expenses. The NHTSA should also open a recall case on this matter for owners like myself.

1.5 liter ecoboost engine has a coolant intrusion problem into the cylinder to due a design flaw. Problem can cause several problems: loosing coolant and causing the engine to overheat, causing misfire in the cylinders, and can cause the engine to stallwhich has happened several time on me. The engine should be recalled as a safety concern for stalling, it has stalled on the I15 in Utah several times

Upon starting my car, the check engine light illuminated. Took my car to my mechanic and they confirmed an engine issue. Also stated the Ford 2.0 Liter engine has a high failure rate. My 2017 Ford Fusion SE (2.0 L Turbo Engine – VIN # [XXX]) with only 82,300 miles, which was purchased new, that has developed a water intrusion issue as identified in the Ford TSB 19-2346. After two separate requests Ford has stated it is out of warranty and will not provide and assistance in repairs, however based upon numerous reports this is caused by a design flaw. Previous recalls on the 1.6 L engine confirm the issue is across this engine family. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Odometer Fraud. The contact purchased a 2017 Ford Fusion. It was discovered that there was a mileage discrepancy. The vehicle was a dealer sale. At the time of purchase, the vehicle mileage was 119,966, but during a repair, it was discovered that the mileage was 200,000.

Noticed that the coolant level kept going down with no apparent external leakage and was also getting a code for #2 Cylinder Mis-Fire, After adding a total 1 gallon antifreeze i made an appointment at the local Ford Dealer to see what is wrong. They Diagnosed the Issue to Coolant leaking in to Cylinder #2, there recommendation is to replace Long Block.

My torque converter went bad on my 2017 Ford Fusion, it's the same problem the other 2017 Ford Fusions had with their torque converter however my vin is not on the recall.

I recently now am having to replace my engine a second time in 2 years due to a coolant intrusion problem

The vehicle's electrical system intermittently fails while driving. The entire instrument cluster and electronics shut off (speedometer, gauges, and all warning indicators go dark) while the engine continues running. On one occasion this occurred at night on a highway, with sudden loss of dashboard and electrical function until the vehicle could be pulled to safety, rendering the vehicle essentially invisible. The failure has worsened over time and now includes audible relay clicking near the center console and failed remote-start commands. The problem has been reproduced and confirmed by an authorized Ford dealer. After multiple prior visits where the dealer could not reproduce the fault, the dealer verified the concern and connected a scan tool, finding that all modules on the HS1-CAN communication bus stopped communicating. The dealer checked technical service bulletins, performed pinpoint tests, and verified connector pin fitment. The dealer's diagnosis is a failed Gateway Module, with replacement recommended. The vehicle remains available for inspection. Warning symptoms preceding the failures include the dashboard going dark, electronics resetting, fault codes appearing on restart, and remote start malfunctioning. This is a serious safety risk: loss of the instrument cluster, lighting, and electrical systems while driving, particularly at highway speed and at night, eliminates the driver's ability to monitor speed and warning indicators and can result in loss of visibility. This failure pattern is widely reported by owners of this model and appears consistent with Gateway Module defects addressed by recall on newer model-year Fusion vehicles.

NHTSA recall 23V-162/Ford recall 23S12 Vehicle suffered secondary failure of recall remedy part which caused an immediate loss of braking ability. Ford dealer refused a safety tow unless I paid for it upfront which forced me to use my personal roadside insurance. After calling local dealer to assure vehicle had arrived after being towed, dealer said they couldn't look at vehicle until Tuesday , five days later because of the weekend and holiday.

The rotary gear shift knob occasionally gets stuck and refuses to rotate back to Reverse (R). This intermittent failure has occurred 3 times within this month. The dashboard does not show any warning lights or error codes during the incident. This is a severe safety hazard as it could leave the vehicle stranded in traffic or unable to back away from danger. Took the vehicle to the Ford dealership(Citrus Motors Ford) for inspection, but they returned it as "Could Not Duplicate" because no active diagnostic trouble codes (DTCs) were stored. However, the physical shifting malfunction remains an active threat.

While pulling into my parking garage at work I put my 2017 Ford Fusion into park to open the door and scan my card. When I tried to shift out of park the gear shifter indicated a shifting fault that required service. The car was towed to a Ford Service Center where the problem as diagnosed to be the shift control linkage, specifically the shift cable bushing. I have come to understand that this part has had issues in the 2013-2016 Ford Fusion models resulting in a recall. This issue appears to also be in the 2017 Ford Fusion as the results of the fault are identical to those of the 2013-2016 models. The component has been diagnosed by a certified ford service center. There were no warning lamps or prior indicators of this issue. Warning lamps only turned on after the issues occured.

NHTSA claim # 11739491 update 05/22/2026 Young Ford Ogden Utah is refusing to execute the remedy for open safety recall 23S12 on my vehicle. They are refusing to run diagnostics test to honor the recall without paying $100 and up fee.

The car overheated due to coolant leaking. Found out vehicle has a coolant intrusion requiring a new engine now.

I was driving and the car just stopped it wouldn't let me put in park or drive it just stayed in neutral. And I was stuck it kept the the emergency break on. Then it wouldn't turn off all the way which caused the car to drain battery.

Coolant leak into engine block, ford dealership said $8,000 to replace engine cars only at 65k miles. Problem is from manufacturer defect in the 2.0l TT turbo engines in fusions and should be recalled as it’s not the owner/operators wrong doings.

Coolant intrusion, problem.

The contact owns a 2017 Ford Fusion. The contact stated that while driving approximately 35 MPH, the rear end of the vehicle unexpectedly locked up. There was no warning light illuminated. The vehicle became inoperable and was towed to the residence. The dealer was contacted. The vehicle was not diagnosed or repaired. The contact associated the failure with NHTSA Campaign Number: 24V102000 (Power Train). The manufacturer was made aware of the failure. The failure mileage was approximately 80,000.

Component/System: Engine — 1.5L EcoBoost short block coolant intrusion leading to catastrophic engine failure. Vehicle is available for inspection upon request. Safety Risk: Vehicle overheated while in operation, creating risk of engine fire, loss of vehicle control, and stranding of occupant on a public roadway. Ford's own TSB 22-2322 acknowledges this defect creates a fire risk. Confirmed by dealer/shop: YES Inspected by manufacturer/police/insurance: Ford Motor Company was contacted on 17APR26 and opened case number XXX but denied coverage citing vehicle assembly location [XXX] ) despite the defect being present in all 1.5L EcoBoost engines regardless of assembly plant. Warning symptoms: Vehicle exhibited overheating warning prior to failure. Coolant intrusion into cylinder bores is a known documented defect covered under Ford Customer Satisfaction Program XXX and TSB XXX for identical engines in US-assembled vehicles. Mileage at failure: Approximately 65,000 miles. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Coolant light and check engine lights kept coming on. The car was diagnosed by the Ford Dealership as Ford TSB 22-2229, which is a design flaw in specific EcoBoost engines, where an "open deck" block causes coolant to leak into cylinders 2 and 3, leading to severe engine failure. To fix this issue, the TSB requires replacing the entire long block assembly with a redesigned version featuring enhanced sealing surfaces. The cost for this new engine was quoted as $8000 to $9000.

Dec 2022 I purchased a 2017 Ford Fusion. In June 2023 the engine needed replaced which was covered under warranty. In March 2026, the flex plate breaks and now needs to be replaced. This is the original part for this car as I confirmed with the dealer that this part isn't required to be replaced when the engine is replaced. So it's not covered under vehicle warranty or the motor repair warranty. However, there is a known issue of these flex plates breaking and there is Customer Satisfaction Program 22N12 for Ford Fusions regarding this known issue that only covers years 2019 & 2020. I want the 2017 year to be added to this as a known issue.

Technical Safety Bulletin 19-2346; coolant infiltrating cylinder #2. Quoted $8350 for long block repair.

I was experiencing engine vibration while driving and lack of power when I pressed gas pedal. I took it to an independent garage first, and then to the dealer. Both told me there was coolant and water in the cylinders, and the dealer told me I needed a total engine replacement consisting of the long block and the head gasket. And it was going to cost me $14,000. my car only has 44,000 miles on it and Ford told me there was nothing they could do about it even though it was a known issue dating back several years.

The contact owns a 2017 Ford Fusion. The contact stated that upon starting the vehicle, the engine experienced a rough start and idling, and the check engine warning light was illuminated. The vehicle was taken to a local dealer where it was diagnosed, and the contact was advised that the engine was faulty due to coolant intrusion. The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 90,000.

The contact owns a 2017 Ford Fusion. The contact stated that upon reversing out of the driveway and attempting to shift to drive(D), the message "System Fault - Consult Manual" was displayed. The contact was not able to shift to drive(D). The contact looked underneath the vehicle and noticed that the shifter cable was loosened. The contact was able to insert a screwdriver into the end of the cable, and the contact was able to shift to drive(D). The contact drove to the residence. The vehicle was taken to a dealer, where it was diagnosed and determined that the shifter cable bushing had failed and needed to be replaced. The vehicle was not repaired. The contact related the failure to an undisclosed recall however, the model year was not included. The dealer confirmed that the vehicle was not covered. The manufacturer was informed of the failure and referred the contact the NHTSA Hotline for assistance. The failure mileage was approximately 150,000.

Torque converter is gradually failing. Started at 50,000 miles. No warning lamps, messages.

2017 Ford Fusion got serviced at Ford dealership June 4, 2025. Service included, transmission flush, fuel induction service, oil change, oil filter change. About a month after service check engine light comes on upon starting the vehicle, but then goes out. A week later check engine light comes back on and would not start properly. Vehicle taken to independent mechanic and was told transmission fluid was low and also old. Vehicle taken to Ford dealership where service was done month prior. Ford dealership said cylinder misfire, coolant intrusion, and engine failure. Also transmission fluid was found to be low. Ford recommended new engine.

The contact owns a 2017 Ford Fusion. The contact stated that while driving 40 MPH, there was an abnormal slushing sound coming from the engine compartment. Additionally, the vehicle shuddered violently, the engine overheated, and the vehicle stalled. The check engine and powertrain warning lights were illuminated. The vehicle was able to restart. The vehicle was taken to the dealer, where it was diagnosed with engine failure. The dealer determined that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 136,000.

Vehicle is experiencing coolant intrusion from a crack in the engine block which is a known issue by Ford for my particular vehicle year (2017). Ford has issued a TSB/Recall for model years 2017-2019, but when I contacted Ford, I was told my car is not eligible/included in the recall because of the plant that the vehicle was manufactured at. I believe this issue should qualify for manufacturer recall as this is known issue.

The contact owns a 2017 Ford Fusion. The contact stated that there was white smoke coming out of the exhaust pipe on cold starts and while driving at various speeds. The check engine warning light and the low coolant warning light were illuminated. The vehicle was taken to an independent mechanic, where it was diagnosed with coolant intrusion into the cylinders through a cracked engine block. The mechanic determined that the engine needed to be replaced. The mechanic informed the contact that it was known failure and referred the contact to a dealer for assistance. The vehicle was not repaired. The manufacturer was notified of the failure and referred the contact to the NHTSA for assistance. The failure mileage was approximately 196,000.

My engine experienced coolant intrusion into cylinder #2, which caused misfiring and engine failure. This has been a known issue with this year model, but since I am just outside of the warranty mileage (69K) and my VIN doesn't have any recalls, I have been advised to purchase a replacement engine. I simply cannot afford to replace an engine in a car I am still paying a loan for. For this to be a known issue and not be recalled is a serious safety concern and has caused me to lose confidence in the manufacturer. I am currently trying to see what a shop near me would charge to replace it but I am not sure that I can afford the repair costs. I shouldn't be expected to need to replace an engine when the year model has known issues and I have taken care of any and all maintenance on the car to keep it running well. I expected to have this car for many more years, especially with the low mileage and how well I've cared for it.

The contact owns a 2017 Ford Fusion. The contact stated that while driving at various speeds, during acceleration or deceleration, the transmission was shifting roughly. The contact stated that at slow speeds, the vehicle was vibrating abnormally. The contact stated there were no warning lights illuminated. The local dealer was contacted; however, the vehicle was not taken to the dealer. The vehicle was not diagnosed or repaired. The manufacturer was informed of the failure. The contact researched online and related the failure to NHTSA Campaign Number: 17V427000 (Power Train); however, the VIN was not included in the recall. The failure mileage was approximately 136,000.

The vehicle's engine is experiencing coolant intrusion. As such, when starting the car, white and sweet-smelling exhaust exits the exhaust pipe. Furthermore, the coolant reservoir continually runs low; however, we find no coolant on the driveway or apparently leaking from the car. That supports the mechanics assessment of a coolant intrusion. This issue, if left unaddressed, will cause the engine to run improperly, the spark plugs to become fouled, the engine to overheat, etc. I took the vehicle to a local certified mechanic. Although after looking at Ford's service bulletin, it became apparent that the vehicle is experiencing a similar issue to other 2017 models that were included in the recall. The mechanic listened to what we said and pulled up supporting documentation in the form of a Technical Service Bulletin. The check engine light just came up, within the past couple of days, well after the coolant intrusion was started. The disrepair seems to be a matter of timing. The subject has been driven quickly and cautiously.

The contact owns a 2017 Ford Fusion. The contact stated that while reversing out of the driveway, the parking brake had unintentionally activated, causing the vehicle to abruptly stop. Upon inspection, the contact discovered that the transmission shifter cable bushing had failed, causing the shifter cable to detach. The vehicle was not yet repaired. The manufacturer was notified of the failure, but no assistance was offered. The contact was informed that the VIN was not included in NHTSA Campaign Number: 22V413000 (POWER TRAIN). The contact stated that the vehicle had experienced the failure listed in the recall. The local dealer was not contacted. The failure mileage was 105,000.

The contact owns a 2017 Ford Fusion. The contact stated that after starting the vehicle and shifting to drive(D), the message "Shift System Fault" was displayed, and the gear shifter erroneously shifted back into park(P). The vehicle was undrivable and was later towed to the local dealer who replaced the shifter cable bushing, and the vehicle was repaired. The contacted stated that the failure had recently reoccurred. The contact was able to reconnect the shifter cable bushing and the vehicle was repaired. The manufacturer and local dealer were notified of the failure. The failure mileage was 100,000.

What malfunctioned- Car did not give any notice that it was in engine failure for months other than under performing and upon taking it to the ford dealership was never helped with the problem they took money for an oil change and works package but failed to make sure my car was safe. My car was a safety hazard bc it gave zero warning that it was loosing power and when the engine did fail I knew something had been wrong for almost a year and felt it went ignored by Ford and was taken advantage of. The product has been confirmed by multiple mechanics that what causes it is the hose cracks and thus the engine coolant wrecks a working engine. Ford knows it’s a problem but isn’t acknowledging it and makes more money off of parts.

The contact owns a 2017 Ford Fusion. The contact stated while driving 65 MPH, the check engine warning light illuminated. A dealer was contacted. The vehicle was taken to a dealer to be diagnosed and it was determined that the engine had failed and needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure and informed the contact that the engine was out of warranty. The contact was referred to the NHTSA Hotline for assistance. The failure mileage was 110,000.

On June 23, 2025, while departing my residence, I disengaged the emergency brake on my vehicle, subsequently hearing an unusual sound. Upon attempting to drive, I experienced diminished braking performance, and the brake warning indicator illuminated. The following day, I sought a professional assessment at Big O Tires. Their diagnosis identified a failure in the left brake hose, recommending the replacement of both. Following their recommendation, I proceeded with the necessary repairs. Subsequently, I received notification of a manufacturer recall addressing this specific issue. Consequently, I am seeking reimbursement for the previously completed service. Despite my attempts to obtain a resolution through direct communication, I have yet to receive a response, and I am now seeking assistance in this matter.

The contact owns a 2017 Ford Fusion. The contact stated that while operating the vehicle, the check engine warning light illuminated, and the engine overheated. The vehicle was taken to the local dealer who diagnosed the vehicle and determined that there was coolant inside the cylinders and advised the contact that the engine long block needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure, but no assistance was offered. The contact was informed that the vehicle did not qualify for an Extended Warranty Coverage related to the failure. The failure mileage was 55,700.

The contact owns a 2017 Ford Fusion. The contact stated while driving at an undisclosed speed, the check engine warning light illuminated, and the vehicle lost motive power. The vehicle was driven to the dealer where it was diagnosed with engine failure. The contact was informed that the engine needed to be replaced. The vehicle was repaired. The manufacturer was made aware of the failure and a case was filed. The contact was advised to contact the NHTSA Hotline to report the failure. The failure mileage was approximately 50,000.

Engine is experiencing the all too common coolant intrusion.

The contact owns a 2017 Ford Fusion. The contact stated that upon starting the vehicle, the check engine and the service vehicle soon warning lights were illuminated. The vehicle was taken to a local dealer where it was diagnosed, and the contact was advised that the engine was faulty due to coolant intrusion, and that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 123,000.

The contact owns a 2017 Ford Fusion. The contact stated while driving at an undisclosed speed, the check engine and service warning lights illuminated. The vehicle was taken to the dealer where it was diagnosed with a failed torque converter clutch and a failed transmission. In addition, the contact was informed of metal found in the oil. The contact was informed that the transmission needed to be replaced. The vehicle was not repaired. The manufacturer was made aware but provided no assistance. The contact referenced NHTSA Campaign Number: 17V427000 (Power Train); however, the VIN was not included in the recall. The contact was advised to contact the NHTSA Hotline to report the failure. The failure mileage was approximately 117,000.

In July 2025, my 2017 Ford Fusion SE (EcoBoost engine) was diagnosed with coolant intrusion into cylinder #4 by Sunrise Ford in North Hollywood, CA. This is a known issue with the 1.5L and 2.0L EcoBoost engines and is addressed in Technical Service Bulletin (TSB) 19-2208. The vehicle had only 76,000 miles at the time and had been regularly serviced and well-maintained. Over the past 1–2 years, I received repeated warnings during oil changes that my coolant levels were unusually low, though no leaks were found. In July 2025, the check engine light (CEL) appeared. The vehicle exhibited rough idle at cold start, but otherwise drove normally. I immediately brought the car to the dealership, where they confirmed the problem through diagnostics and plug inspection. The dealership quoted me $11,000–$12,000 to replace the engine (long block). Ford Customer Relations (CRC) was contacted and denied financial assistance, citing the age of the vehicle. They also acknowledged this is a known issue and suggested I file a report with the NHTSA, which I am now doing. This engine failure presents a serious safety risk. The CEL appeared without warning during normal use. A driver unfamiliar with the signs of internal coolant loss could continue operating the vehicle, risking a sudden loss of engine power, stalling, or further engine damage while in motion. In my case, the failure occurred quietly and was only caught because I acted quickly. Had I ignored the CEL or rough idle, engine failure could have occurred at highway speed. The issue was confirmed and documented by a Ford dealer. I am no longer in possession of the vehicle, as I was forced to sell it at a loss due to the cost of repairs. The vehicle is no longer available for inspection, but all related documentation has been retained.

The contact's husband owns a 2017 Ford Fusion. The contact stated that the check engine warning light was illuminated. The contact used a vehicle code reader and scanner tool to scan the vehicle and retrieved a diagnostic trouble code indicating a misfire in engine cylinder #2. The vehicle was taken to an independent mechanic where, the coil pack and plug wire were replaced; however, the failure recurred days later. The vehicle was taken back to the independent mechanic, where it was diagnosed with coolant intrusion in engine cylinder #2. The mechanic informed the contact that the failure was related to Ford TSB Number:19-2346. The vehicle was not repaired. The manufacturer was notified of the failure and a case was filed. The contact was then referred to the NHTSA Hotline to file a complaint. The failure mileage was 78,850.

The contact owns a 2017 Ford Fusion. The contact stated that while starting the vehicle, the contact heard a loud clanging sound coming from the engine compartment, with the check engine warning light illuminated. The vehicle was taken to an independent mechanic, where it was diagnosed with coolant intrusion into the engine. The contact was informed that the head gasket and short block needed to be replaced. The vehicle was not repaired. The dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure. The approximate failure mileage was 46,791.

Manufactured dates for the 2.7L engine put only into the trim model Ford Fusion Sport (a rare trim) during 06/16 - 01/17 have been documented to have cylinder head issues resulting in long block issues. (Meaning a whole new engine is needed) the only way you got this issue fixed is if it was done in the first 3 years of 2017 or within 39k miles. But for those that didn’t get their vehicles in during that time frame are supposed to pay out of pocket for a defect ford knew to exist and have no issued a recall on these vehicles.

The contact owns a 2017 Ford Fusion. The contact stated while attempting to start the vehicle, the vehicle hesitated to start and was shaking abnormally. The contact stated that the check engine warning light was illuminated. The contact stated that a dealer was contacted. The vehicle was taken to the dealer and was diagnosed with coolant intrusion into the engine. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure and opened a case. The contact was referred to the NHTSA Hotline for assistance. The failure mileage was 130,000.

The contact owns a 2017 Ford Fusion. The contact stated that while operating the vehicle and attempting to close the front passenger side window or the front driver's side window, the windows raised up but failed to remain closed. The contact stated that the windows immediately rolled back down independently. The cause of the failure was not yet determined, and the vehicle was not repaired. The local dealer and manufacturer were notified of the failure, but no assistance was provided. The contact was informed of a TSB related to the failure, but no assistance to repair the vehicle was offered. The failure mileage was 22,000.

The contact owns a 2017 Ford Fusion. The contact stated that while attempting to reverse, the vehicle failed to shift into reverse. The contact stated that the transmission returned to park(P), and the gear shifter detached. The contact stated that someone nearby was able to reattach the shifter, and the contact was able to drive the vehicle to the residence at slow speeds. The contact learned of NHTSA Campaign Number: 22V413000 (Power Train); however, the VIN nor the model year was not included. The dealer was contacted and confirmed that there was no recall on the VIN. The vehicle was not diagnosed or repaired. The manufacturer was informed of the failure and confirmed that the VIN was not under recall. The manufacturer opened a case for the failure. The manufacturer referred the contact to the NHTSA Hotline to report the failure. The failure mileage was 67,793.

I purchased my 2017 Ford Fusion Titanium brand new with only 5 miles, from a dealership in Ky. My car recently started idling rough when I started it up. I took my car to a mechanic, after the check engine light came on. The code read misfire on cylinder 3, they replaced spark plugs and coils for $600, but only a few days later the check engine light came back on, still rough idling. I take my car to a 2nd mechanic $200, to find out that there is a “coolant intrusion” in the cylinders, indicating I would need a new engine. In disbelief, I take my car to a 3rd mechanic, $100. I have records from two different mechanic shops showing that there is a coolant intrusion in the engine, which is a "manufacturer defect". I called Ford's Corporate Office for help and apparently my VIN was not a part of any recall, although there are many recalls for the same issue, in the same year and model! There’s a recall on the car engine itself (per 3rd mechanic). Ford told me they couldn’t do anything about their manufacturer issue. Research initiated by the mechanic indicated that Ford Fusion cars with the same make and model, along with many other Ford models in the same year of 2017-2019 had the same issue of coolant intrusion into the cylinders and have been recalled. There are also active lawsuits over the same issue. It’s honestly unbelievable and disheartening that my car is not a part of the recall when it’s doing the exact SAME thing as others with the same year and model, which have already been recalled. I cannot afford to put a new engine in my car. It should have lasted a lot longer, and would have, if it weren't for a Ford manufacturer issue. I have all the documentation as needed, which states that I need a new engine and that the engine itself has already been recalled (however, the VIN shows no recall for the car). I will also be reporting this issue to the National Highway Traffic Safety Administration. Thank you for your time on this matter.

The contact owns a 2017 Ford Fusion. While the contact's husband was driving at an undisclosed speed, the transmission seized. There was no warning light illuminated. The contact stated the vehicle stalled in the middle of traffic. The vehicle was towed to the residence. The vehicle was then towed to an independent mechanic where it was diagnosed with transmission failure. The contact was informed that the transmission needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure but provided no assistance. The contact was advised to contact the NHTSA Hotline to report the failure. The failure mileage was approximately 111,700.

When my wife returned home from shopping she parked in the driveway I was going out so I had to move her car to get to mine. I saw a puddle of brake fluid on the ground and the brake light was on there was no fluid in the master cylinder . the car was towed to my mechanic and he found a rotted brake in the rear of the car up between the gas tank and rear seat right under a rubber clamp that holds the line this could have caused a tragedy. I connected Ford they said rusted brake lines are not covered even though they are coated.

The overheat light came on and antifreeze was leaking into the number 4 cylinder of the spark plug, sometimes it would lose a little power

No accident just looking to fix the recall

The contact owns a 2017 Ford Fusion. The contact stated while driving at an undisclosed speed, the vehicle jolted and there was white smoke coming from the exhaust pipes. The vehicle was taken to a local independent mechanic where it was diagnosed with a coolant intrusion and a blown head gasket. The mechanic related the failure to the Customer Satisfaction Program: 21N12. The local dealer was contacted; however, the vehicle was not diagnosed or repaired because the VIN was not under recall. The manufacturer was made aware of the failure. The failure mileage was approximately 95,000.

The contact owns a 2017 Ford Fusion. The contact stated while the vehicle was parked and occupied, and attempting to start the vehicle, the check engine warning light illuminated. The contact stated that after shifting into reverse and reversing out of the driveway, the check engine warning light illuminated. The local dealer was contacted. The vehicle was taken to the deale,r where it was diagnosed with coolant intrusion into cylinder #4. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure but offered no assistance. The contact was referred to the NHTSA Hotline for assistance. The failure mileage was 47,183.

While driving the car, the engine indicator kept blinking then the car kept shaking. The Ford Service did inspection and found that there has been a coolant leak to Engine Oil which caused Engine Failure due to cylinder break.

Engine is losing coolant into the cylinders which causes car to overheat. When this happens car shakes and runs rough. When this occurs while driving down the road, thick white smoke comes from the exhaust blinding the cars behind us. If car dies, you lose power steering and brakes become very difficult to push. We had a repair shop check it out and coolant is leaking on top of the piston and exiting through the exhaust. The engine light comes on just before car begins to act up. According to our mechanic, it appears the engine block has a design flaw and Ford has issued a Technical Service Bulletin explaining the problem. Attached a picture of when it just begins to smoke. After a few seconds it fills the entire shop.

The contact owns a 2017 Ford Fusion. The contact stated that there was coolant leaking into the engine and there was smoke coming from the exhaust. The contact stated that the engine was overheating. The check engine warning light was illuminated. The vehicle was taken to an independent mechanic where a pressure test was performed and determined that the engine was not maintaining the proper engine pressure, and coolant was entering the cylinder walls. The contact called the local dealer, who confirmed there was no recall coverage for the failure and referred the contact to the manufacturer for assistance. The manufacturer was contacted and referred the contact to the NHTSA Hotline. The failure mileage was approximately 120,000.