Ford Explorer 2019 — Reported problems

The contact owns a 2019 Ford Explorer. The contact stated that while driving at various speeds, the radio displayed the rear-view camera image or rebooted. The dealer was notified of the failure by phone and informed the contact that the VIN was not included in a recall associated with the failure. The failure mileage was approximately 115,000.

We have contacted Ford Motor Company previously about this issue. The leather dash pad on our Explorer is detached near the windshield and is rolling up back towards the interior of the vehicle. The dealer has inspected (Deacon Jones, Goldsboro, NC) and has confirmed the issue. Original quote to fix was approximately $15,000.00, reduced later by FMCO to $6000.00. We have attempted to find local upholstery shop to repair, but they will not touch it. The pad underneath the leather is all white and causes a debilitating glare/reflection on the windshield when driving towards the sun. Please review my previous filing with FMCO and help us with this issue. I note that online, several others are experiencing this same issue. This is developing into a severe safety issue.

The cowl grille/top trim has become extremely brittle and deteriorated. The material is breaking apart simply from being touched, and pieces are coming loose and flying off while I’m driving. the entire edge of the cowl is crumbling and separating from the vehicle. This appears to be material deterioration rather than normal wear. I’m concerned that additional pieces could detach while driving and that the cowl may no longer properly protect/seal the area beneath the windshield.

The contact owns a 2019 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, upon taking the vehicle to a local dealer, no failures were found, and the VIN was removed from the recall. Upon further inspection, the contact became aware that the front driver’s side and passenger’s side A-pillar trims were loose. The local dealer was contacted. The manufacturer was made aware of the failure. The failure mileage was approximately 73,000.

Driver side roof rack cover blew off while driving on the highway. Dealer says they previously repaired this under an existing recall and is not going to fix it again. I understand a new recall was issued in July 2026, but our vin is not covered even though ours blew off

The contact owns a 2019 Ford Explorer. The contact stated that while the vehicle was parked, the message "Right Rear Door Ajar" was displayed. The contact moved the rear passenger’s side door latch several times and was able to fix the failure. However, the failure recurred. The contact was concerned that the failure would drain the battery.

The contact owns a 2019 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The contact stated that while driving at an undisclosed speed, the front A-pillar trims detached. The contact was able to replace both A-pillar trims; however, the failure reoccurred. The local dealer was contacted. The manufacturer was made aware of the failure. The failure mileage was approximately 50,000.

The internal timing-chain-driven water pump on my 2019 Ford Explorer Sport 3.5L EcoBoost is failing. I began experiencing coolant loss and the cabin heat would turn cold while the vehicle was stopped or idling. The vehicle was professionally inspected by an independent repair facility. After diagnostic testing, the mechanic confirmed coolant leaking from the water pump weep hole and diagnosed a failing internal water pump. The water pump is located inside the engine and is driven by the timing chain. Continued failure can result in significant coolant loss, overheating, coolant entering the engine oil, and potentially severe engine damage or engine failure while driving. I am concerned about the safety risk of an unexpected loss of engine operation. The vehicle did not initially display an overheating warning despite the coolant loss and heating symptoms. The failure has been confirmed by a professional mechanic and documentation/photos of the leak and diagnosis are available upon request. Replacement requires extensive engine/timing-system disassembly and I was quoted several thousand dollars for the repair. I am requesting that NHTSA investigate internal water pump failures involving the 3.5L engine used in these Ford Explorer vehicles.

I was driving down the road when the warning lights suddenly came on, and the vehicle would not allow me to accelerate. As a result, my vehicle slowed unexpectedly, and another vehicle nearly struck me from behind.

In November 2025 vehicle began experiencing intermittent instances of rough shifting when the engine was under strain due to mountain driving. Since we do not live in the mountains, we returned home and waited to see if it would replicate. Vehicle began intermittently, replicating, hard shifting when coming out of Park. At that time an appointment was made with a local transmission shop in June 2026 to have an evaluation done. No error codes have been thrown at any point in time but the shop was able to highlight that there are metal flakes in the transmission fluid indicating the beginnings of mechanical malfunction of the transmission prior to 150,000 miles. At the time this started the vehicle was at approximately 137,000 miles. It is now at approximately 154,000 approximately one year later. It is my daily driver and only motive transportation. Shop has recommend a transmission rebuild due to metal flakes in the engine. It is a well-known fact, two Ford that they installed faulty, transmissions that prematurely go out however, they have not completed a recall to this date still. This puts unnecessary financial hardship on the consumer when the vehicle starts to fail prematurely.

Both the rear toe links were replaced under NHTSA # 26V101 on March 26th, 2026. On August 8th, 2026, the vehicle experience significant handling issues at highway speeds. Was found the toe links shifted post recall. Significant cambered tire wear located on both rear tires. The axel shaft seal developed a leak from the suspension system strain caused from toe links failing. My families safety was at risk due to the tires and suspension failing causing significant handling issues at highway speeds. The vehicle was parked immediately after inspecting the rear end. Approximately 4,500 miles driven since recall service. Vehicle is now back with FORD dealership as of August 11th, 2026 for inspection. FORD dealership is expected to invoice repair costs for failed axel shaft seal. FORD is covering the rear tire replacement along with re-alignment. No warning lamps or messages observed.

The contact owns a 2019 Ford Explorer. The contact stated that the vehicle was taken to the dealer to be repaired under NHTSA Campaign Number: 24V031000 (Structure); however, the recall repair was not performed because the A-pillar trim had not completely detached. While driving the vehicle at an undisclosed speed, the A-pillar trim detached. The dealer was contacted after the trim had fully detached, but recall repair was not performed. The contact stated that the dealer cleared the recall from the VIN and refused to perform any repairs associated with the recall. The manufacturer was made aware of the failure and referred the contact to the NHTSA Hotline to report the failure. The failure mileage was approximately 90,000.

Passenger side exterior B pillar trim came off while driving on highway on July 3, 2026. Trim was on vehicle when it left home. It was not on it when it arrived at destination. Possible danger to other drivers from flying trim component. No inspection or any symptoms of the problem prior to failure. Same problem as recall on 2016-2017 models.

The contact owns a 2019 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated that the exterior A-pillar trim had detached from the vehicle. The dealer was made aware of the failure but confirmed that parts were not yet available. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 44,000.

Component/System: Aluminum hood panel (front edge seam). The hood is available for inspection upon request. The front edge of the aluminum hood on my 2019 Ford Explorer has developed bubbling, lifting paint, and corrosion originating from inside the folded seam. The defect has progressively worsened over time and continues to spread outward. Safety Risk: The corrosion is occurring at the front hood seam, which is part of the structure that supports the hood latch area. Progressive corrosion in this region may weaken the hood panel over time, potentially affecting hood retention at highway speeds. Paint loss and metal degradation also reduce visibility of the defect until it becomes severe. Reproduction/Confirmation: The problem is visible and reproducible at any time. The bubbling and corrosion are present continuously and worsen with normal vehicle use. Inspection History: The issue has been visually inspected by me. The vehicle has not yet been inspected by the manufacturer, dealer, police, or insurance representatives. Warning Lamps or Messages: No warning lamps or messages appeared. There were no electronic symptoms prior to the failure. The first visible symptom was small paint bubbles along the front hood edge, which appeared approximately when the corrosion began. Assessment: Based on widespread reports for this model year and Ford’s own Technical Service Bulletins for aluminum panel corrosion, the cause appears to be corrosion originating inside the aluminum hood seam, likely due to manufacturing contamination.

The contact owns a 2019 Ford Explorer. The contact stated that the leather on the dashboard was peeling and had detached. No warning lights were illuminated. The local dealer was contacted, but the vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 100,000.

The contact owns a 2019 Ford Explorer. The contact stated that while driving 80 MPH, the steering wheel was abnormally loose, and the vehicle became uncontrollable. The contact stated that the brake pedal was depressed; however, the vehicle failed to stop as intended. The vehicle was driven to the shoulder of the road, and the brake pedal was depressed to the floorboard. The brake pedal was depressed several times, and the vehicle stopped. No warning lights were illuminated. A driver nearby assisted with stopping traffic to allow the contact to drive the vehicle off to the shoulder of the roadway. The vehicle was inspected, and the other driver became aware that the rear tires were completely bald. The vehicle was taken to Discount Tires, and the contact was informed that the failure was because of the rear suspension. The contact was advised to take the vehicle to the dealer. The vehicle was taken to the dealer and was informed that the vehicle was previously repaired under NHTSA Campaign Number: 26V101000 (Suspension) in March 24, 2026. In addition, the contact was informed that an alignment was not performed because the alignment machine was unavailable. The contact had not been informed that the recall repair was completed. The dealer informed the contact that an alignment had been completed. The vehicle was repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 147,419.

Fuel pump and module failure. Driving on the highway at 70 miles an hour and the fuel pump failed. Causing me to have zero acceleration. Thus losing speed rapidly in the center lane. No warning lights were present before or after. One previous symptom of a crank no start. Dealership was able to replicate the crank no start situation. Resulting in the problem being a fuel pump failure and module needing replaced, at 83,000 miles on the vehicle. Though I know normal wear and tear can and does happen, there was no warning. And losing engine power at high speeds on a highway is unsafe.

This recall has been unresolved for approximately two years. Recently, while traveling at highway speeds, the A-pillar trim detached from my vehicle and flew off, striking a vehicle behind me. Fortunately, no accident occurred, but the situation was extremely dangerous and could have resulted in serious injuries or property damage. This is precisely the type of incident the recall was intended to prevent. I have reached out to my local dealership numerous times and am told that Ford has no parts available. This is not acceptable and Ford is not handling this recall in a timely fashion.

The contact owns a 2019 Ford Explorer. The contact stated that while driving, Panel on the driver side door, keyless pad became completely detached. The vehicle was taken to a dealer where it was diagnosed as not being fully secured and was replaced. The panel blew the fuses and affected the liftgate on the vehicle and additional repairs, latch replacement on the liftgate had to be completed. The manufacturer was notified of the issue. The approximate failure mileage 47,000.

While my granddaughter was driving our 2019 Ford Explorer, the steering effort suddenly increased without warning, as if the electric power steering assist stopped functioning. She was traveling at approximately 45 mph on a public road and was unable to steer normally. The sudden loss of assist caused her to nearly leave her lane and almost resulted in a collision. This vehicle uses an electric‑assist rack‑and‑pinion steering system. There were no warning lights or messages before or during the event. Road conditions were dry. After the incident, steering remained abnormally heavy/intermittent. It isn't as though it mimics an old school vehicle without power steering, where it simply requires a good deal of strength. With this situation, if you work hard to make a correction, the car suddenly pulls further quickly in that direction, or in the opposite direction in a very jerky manner. The failure occurred without any prior symptoms and created an immediate loss‑of‑control hazard, especially for younger or smaller drivers who cannot overcome the sudden increase in steering force. It basically feels like it is locked up. I am reporting this because the failure was sudden, unannounced, and nearly caused an accident. This appears to be a malfunction of the electric power steering assist system, and it presents an unreasonable safety risk. On a related note, I am the Director of Quality for a manufacturing facility and have conducted hundreds of formal risk assessments during product design. A sudden, unannounced loss of steering assist represents a high‑severity, low‑tolerance safety hazard. In my professional opinion, this failure mode warrants an accelerated investigation.

I had my transmission replaced in California on Feb 2025. Had failure issues and took it to ford, they found an issue with the torque converter and replaced 7 months after the new transmission, it was cleaned out for debris and contamination. Early this May took it in again for the vehicle violently shaking, the ford Mechanic before inspecting immediately knew what transmission I had and knew what issue was, said all the 6F35 transmissions are failing. Took it to my local ford dealership who confirmed that the whole transmissions needs to be replaced again. Less than 20k miles on it. Of course this transmission had a law suit filed which was dismissed. Frustrating because it is clearly a known issue. I am currently #10 on the national waitlist for a new transmission. I am expected to be without a vehicle for months.

The contact owns a 2019 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The contact stated that the windshield exterior A-pillar trims had become loose. The local dealer was contacted. The vehicle was not repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the failure. The failure mileage was approximately 75,000.

While driving at highway speeds on the interstate, the B-pillar exterior trim suddenly detached from the vehicle. The trim remained tethered only by the keypad wiring, causing it to flail in the wind and create an immediate road hazard. Simultaneously, the vehicle’s instrument cluster triggered a "Liftgate Open" warning, despite the liftgate being secure. I was forced to make an emergency pull-over onto the shoulder of the interstate—a dangerous situation—to prevent the trim from completely detaching and striking other vehicles. Upon reaching my destination, the vehicle suffered a significant electrical short. The interior lights remained on indefinitely due to the false "liftgate open" sensor reading, and the door keypad became completely inoperable. To prevent a total battery drain and potential fire risk from the short, I had to manually disconnect the battery. The dealership confirmed the failure but stated that current B-pillar recalls (such as Recall 25S53) currently only apply to 2016–2017 models, despite my 2019 model using the same defective clips and adhesive. This failure is identical in nature to Recall 24S02 (A-pillar detachment). The detachment of this trim is a documented projectile hazard. Furthermore, the resulting electrical short in the door harness has compromised the integrity of the vehicle’s sensor system. I am requesting that NHTSA investigate the expansion of the B-pillar recall to include the 2019 model year to prevent further highway incidents.

See attached document for complaint.

Brakes, rotors, tires and now steering column and starting gear is needing replaced after recall of rear toe link in 2019 ford explorer

The massage seat on the driver and passenger front seats malfunctioned. The drivers seat massage pillows stayed inflated on the seat and backrest. Driving to work this morning the massage pillow on the drivers seat popped. This was a very loud almost gunshot type of sound which caused me to swerve my vehicle and almost create an accident. This is due to the massage seat malfunctioning. Ford Motor corp is aware of the issue with the seats and have issued a Technical Service Bulletin but no recall. This is a serious safety issue as this could have caused a major accident while operating the vehicle. Ford Motor Corp refuses to fix the issue with my vehicle as it is no longer covered by my warranty.

I brought my vehicle to Ford Motor Place in Webster Massachusetts to do two recalls, my car was driving normally before the recall service. Immediately after recall work, it does not run properly. The dealer claims transmission failure without prior symptoms. The vehicle only has 70,000 miles.

The contact owns a 2019 Ford Explorer. The vehicle was taken to the local dealer to be repaired under NHTSA Campaign Number: 26V101000 (Suspension). While retrieving the vehicle, the vehicle failed to start. The contact heard the mechanic revving the engine of the vehicle. The dealer determined that the fuel pump and fuel pump module needed to be replaced, and that the failure was not related to the recall repair. The vehicle was not repaired. The manufacturer was contacted and determined that the failure was not related to the recall. The failure mileage was approximately 50,000.

The contact owns a 2019 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The contact stated that the driver's side windshield exterior A-Pillar trim had started to detach while driving. The dealer was notified of the failure, but the vehicle was not diagnosed or repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The failure mileage was approximately 150,000.

Ford had a recall on a Explorer's roof rack covers...In 2021 the dealer glued down the covers. Over time the glue has gone bad and both roof racks are loose causing concern. I recently found out that there was a fix for this. It was installing Christmas tree push clips into cover to secure them. I recently went to the dealer (Sayville Ford, [XXX] ) and inquired about this and adviser stated not recall on file since it was done in 2021. Both roof rack covers are defective. Structure: Body Recall date 2021-05-04 Recall no. 21V316000 Ford Motor Company (Ford) is recalling certain 2016-2019 Explorer vehicles. The retention pins could loosen and allow the roof rail covers to detach from the vehicle. Hide details Recall consequence A detached roof rail cover can create a road hazard, increasing the risk of a crash. Recall action Dealers will install push-pins and replace any damaged rail clips and roof rail covers, as necessary, free of charge. The interim owner notification letter was mailed on June 22, 2021. Owner notification letters (remedy available) were mailed on October 1, 2021. Owners may contact Ford customer service at [XXX] . Ford's number for this recall is 21S22. My vehicle never had push pins inserted according to this recall. Please advise on any help in this matter. I wait your response. Thank You [XXX] [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Vehicle was stolen, sold, and relisted for sale. Open Recalls on vehicle.

The B post on the driver side flew off while driving. This is has been an ongoing issue. Ford has fixed them before and they keep causing issues on both the driver and passenger side. The exterior panel does not stay connected to the truck. It flew off at highway speeds, causing the air and rear tailgate to malfunction after it pulled a wire out. This is a huge safety issue ford refuses to acknowledge.

The a-pillar applique trim, which borders the left and right side of the front windshield of my 2019 Ford Explorer has been under recall since January 2024. I've taken it to Bill Utter Ford in Denton, Texas, on four separate occasions to ask for it to be repaired. Generally stated, every six months since the recall. They tell me its too bad, there are np arts to repair it. Question, how can you all allow 2 years to pass and not force them to do something? On March 29, 2026, the drivers side piece came flying off at 30 miles per hour. Luckily no one was behind me. Now my windshield has no protection trim. Further, I cut my right hand trying to force the broken pieces back in.

My ford dealer will not check 4 wheel alignment at no charge to me. I have two articles that it is mandatory to do a 4 wheel alignment after replacing the rear toe arms on my 2019 ford explorer.

The contact called on behalf of the owner of a 2019 Ford Explorer. The contact received notifications of NHTSA Campaign Numbers: 24V031000 (STRUCTURE) and 26V101000 (SUSPENSION). The contact stated that after the vehicle was stopped at a traffic light, the vehicle stalled. The battery warning light was illuminated. The contact was able to restart the vehicle. The contact stated that the failure was occurring every other day. The vehicle was taken to an independent mechanic. The independent mechanic replaced the Manifold Absolute Pressure (MAP) sensor and an unknown sensor; however, the failure persisted. The contact stated that on a separate occasion, while the vehicle was idling, the vehicle stalled. The vehicle was restarted. The contact stated that while the temperature gauge was midway, the vehicle stalled. The battery warning light was illuminated. The contact stated that whenever the temperature gauge was midway, the vehicle would stall. The vehicle was taken to another independent mechanic who replaced a fractured spark plug and the timing chain. The vehicle was repaired; however, two months after the last repair, the failure reoccurred. The manufacturer was not made aware of the failure. The failure mileage was approximately 130,000.

Similar to NHTSA Recall Number 24V031, driver's "B-pillar" trim (top edge) has detached and loose, and is only secured in-place by remaining anchors/attachments. In inspecting underlying substrate, it appears that a mechanical anchor is missing AND adhesive exhibits cohesive failure (remainder adhesive on both supporting/underlying substrate and backside of trim.

Torque converter failed and had to be replaced within 60000 miles. Know issue to ford but they continue to charge $4,000 to have it repaired. Rear main seal leaks oil within 80,000 miles. Know issue to ford and they continue to charge $3,800 to have it repaired.

I am writing to formally report an issue regarding Safety Recall 24S02 on my 2019 Ford Explorer, which is incorrectly shown as completed by Cornerstone Ford in Elk River, Minnesota. This recall involves the exterior A‑pillar trim on 2011–2019 Ford Explorer vehicles and is a documented Ford safety campaign (24S02 / 24V031). According to Ford’s records and Cornerstone Ford’s reporting, Recall 24S02 is flagged as completed on my vehicle on Jun 2025; however, the actual recall repair has never been performed. It appears only on an estimate repair invoice from July 2025, and I have text message correspondence from the dealer dated December 19, 2025, stating that the part had arrived, yet no recall work was scheduled or completed. Notice on Invoice (attached): [Primary]: S100 - RECALL RECALL RECALL - C/S: NO REMEDY AVAILABLE YET-24S02 EXTERIOR A PILLAR APPLIQUE INSPECTION I am unable to take it to a different dealership because it has been flagged as completed. I contacted Ford's Customer service, and they are taking the dealership's word.

The contact owns a 2019 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure). The local dealer was contacted and confirmed that the part for the recall repair was not yet available. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the issue. The contact had not experienced a failure.