Chrysler 200 2015 — Problemas relatados

While driving or operating the vehicle, the power distribution box will lose power or shut down overall power. After extensive testing it has been determined that this is due to the grounding harness from the PDB to the transmission. All mechanics in the area diagnosed the problem as a bad motor. Paid for the motor replacement only to experience the same exact issues. Receipts available upon request.

I was attempting to turn around on my street and was hit on the driver's side by an oncoming car. Immediately thereafter, I tried to pull into a nearby driveway, but the car seemed to suddenly accelerate tremendously and plowed into the back of a parked car in that driveway. I was trying to brake but had no time as the car accelerated so suddenly. It damaged my grill and the bumper of the car that was hit. It appears that other owners of the Chrysler 200C have experienced similar issues with it accelerating when the driver is trying to brake.

The contact owns a 2015 Chrysler 200. The contact stated that the vehicle experienced electrical issues that caused the instrument panel to be blank intermittently, and the cruise control failed to disengage. The vehicle was taken to an independent mechanic where it was diagnosed, and a software update was performed on the vehicle; however, the failure persisted. The manufacturer was notified of the failure. The contact referenced NHTSA Campaign Number: 15V470000 (ELECTRICAL SYSTEM) as a possible cause for the failure. The failure mileage was 168,000.

The contact owns a 2015 Chrysler 200. The contact stated that while driving 35 MPH, the message that the transmission was too hot was displayed. The vehicle was towed to an independent mechanic, and the contact was advised to take the vehicle to a dealer. The dealer was contacted by phone and made aware of the failure. The vehicle was taken to the dealer, where it was diagnosed with transmission wiring harness and TCM failure. In addition, the contact was informed that the vehicle was repaired under NHTSA Campaign Number: 16V529000 (Power Train); in August 2018. The contact was informed that the repair was not covered under warranty. The manufacturer was contacted by phone, and a case was filed. The failure mileage was approximately 131,000.

My 2015 Chrysler 200 displayed the warning “Service Trans Stop Safely Shut Off Engine to Engage Park.” The vehicle has approximately 79,136 miles. I am concerned this is a safety-related transmission/park engagement defect because the warning indicates the vehicle may not properly engage Park. I am requesting that NHTSA document and investigate this issue and determine whether my vehicle is affected by an existing transmission-related recall or whether the affected vehicle population should be reviewed.

The contact owns a 2015 Chrysler 200. The contact stated that on several occasions while driving, the vehicle unexpectedly shut off. The contact was able to restart the vehicle. The vehicle was towed to an independent mechanic on three separate occasions, and the vehicle was diagnosed. The contact was informed that the power distribution center was inoperable and needed to be replaced. The vehicle was not repaired. The contact referenced NHTSA Campaign Number: 15V470000 (ELECTRICAL SYSTEM); as a possible cause for the failure. The manufacturer was not notified of the failure. The failure mileage was 180,000.

Code C14A7 and internal binding occurred on my 2015 Chrysler 200, which shares the identical PTU architecture as the recalled 2015 Jeep Cherokee.

Electricity light came on as well as overheating light and engine light all at once also stalling

Vehicle does shift to p then desired gear. It stalls at traffic stop lights. Very dangerous. I do not know what the issue is.i got home to test the issue while in drive with brake pushed down as if I were in idle, at a stop light, and it did the same thing in the video.

My vehicle lost power while driving had my new born baby in the car with me I was told that it may be issue an electrical connection from 2 different repair shops Tuscaloosa Chrysler tried to service the car for 2 weeks and stated that it was issue with the PMC but they were unable to locate the issue why the vehicle couldn’t get power and said that they no longer make that model vehicle anymore and they weren’t able to get parts and referred me to Henry Automotive in Tuscaloosa that worked on the vehicle for almost 6 months and weren’t able to locate the problem as to why the car was unable to receive power after both repair shops although after checking past recalls for electrical issues I see that some electrical issues were resolved in the past on the vehicle however I have concerned that the issues may not have been resolved completely

The contact owns a 2015 Chrysler 200. The contact stated that while reversing at an undisclosed speed, the rear-view camera displayed an intermittently distorted, darkened, or green screen. No warning lights were illuminated. The contact researched and was made aware of an unknown recall; however, the VIN was not included. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure. The failure mileage was approximately 65,250.

The vehicle has suffered a total failure of the passenger seat jumper wiring harness, which has completely deactivated the entire Supplemental Restraint System (SRS / Airbag system) and triggered the airbag warning light. This is a known manufacturing defect covered under an active Technical Service Bulletin (TSB). ​A certified Chrysler dealership previously performed a paid repair for this exact TSB defect, meaning the replacement safety component has failed prematurely. The vehicle is currently an active safety hazard on the road, as no airbags will deploy in an accident. Chrysler Corporate has refused to remedy this failed safety system, leaving the vehicle completely unprotected.

While driving my 2015 Chrysler 200, the vehicle randomly shifts into neutral without the driver initiating any gear change. Prior to this occurring, all dashboard warning lights illuminate simultaneously and the odometer display starts blinking so many lights — these appear to be warning signs of an electrical failure that then causes the transmission to shift into neutral while driving and sometimes even not able to shift gears. This has occurred multiple times at normal road speeds and causes sudden loss of power and vehicle control, creating a serious safety hazard. The vehicle was taken to an independent repair shop who confirmed it was an electrical issue beyond their capability. It was then taken to a Chrysler dealership who charged $250 per hour for diagnostics, kept the vehicle for a full day, and was unable to identify the cause. Their only suggestion was an aftermarket radio installed by a prior owner — however an aftermarket radio would not cause all dashboard lights to activate and the transmission to shift into neutral while driving. I contacted Chrysler corporate (Case #97099954) who confirmed no open recalls exist and refused to cover the repair stating the warranty has expired. However this is not a wear and tear issue — this is a safety defect. The sequence of all warning lights activating followed by the transmission shifting to neutral points to a failure in the vehicle electrical control system, possibly the TIPM or Transmission Control Module — both known problem areas on this model. This is a serious safety defect and I am requesting NHTSA investigate this issue on the 2015 Chrysler 200.

I was on

I took my vehicle in for service because cylinder 6 had a misfire and the dealership told me that the Catalytic Converter failed internally and stated it can happen at anytime and it sends metal into the engine causing damage.

My airbag light on the driver side is on. Isn't this a recall part

Airbags deployed 15+ seconds after impact. Passenger airbag deployed from the top of the dash and hit the windshield causing the windshield to shatter.

I honestly believe this has to do with me being discriminated by people even emergency dispatch and police from the city of Inglewood , this is not the first time my car gets tampered with, but to start I already had felt something was off with the vehicle because I was parked and it accelerated all of a sudden last night of 03/24/26 then today on 03/25/26 i was on the freeway on my way to work then I felt something wasnt how the last time I drove it then it accelerated all of sudden and some setting on my car where changed so I returned home I didn’t want to risk my life or anybody else’s so i took pictures of the miles 114199 and how the cars is in case someone tries to take it and cause and incident & tries to cause and organized crime so I can get into trouble

The contact's son owns a 2015 Chrysler 200. The contact stated that while his son was driving at an undisclosed speed, the transmission unexpectedly shifted to neutral (N). The message "Please Place Vehicle in Gear" was displayed. The contact's son was able to drive the vehicle after shifting to drive(D). The vehicle was taken to an independent mechanic, but no cause for the failure was found. The vehicle was not repaired. The mechanic related the failure to NHTSA Campaign Number: 16V529000 (Power Train); however, the VIN was not included in the recall. The manufacturer was made aware of the failure, but informed the contact that there was no recall associated with the VIN. The failure mileage was unknown.

It shuts down the engine or. Does not go in park it has something going on with electrical I can not afford it help please

The contact owns a 2015 Chrysler 200. The contact stated that while driving at an undisclosed speed, the driver’s side headlight failed to function as intended. The message "Headlight not Working" was displayed. The vehicle was taken to an independent mechanic; however, no cause for the failure was found. The driver’s side headlight was replaced; however, several days later, while driving at an undisclosed speed, the passenger’s side headlight failed to function as intended. The vehicle was taken to an independent mechanic. However, no cause for the failure was found. On a separate occasion, while driving at an undisclosed speed, the transmission failed to shift as needed. While the shift button was moved to reverse(R), the reverse(R) light failed to illuminate, and an abnormal dinging sound was coming from the vehicle. The message "Transmission Issues" was displayed on the instrument panel. The vehicle failed to move while in reverse. The contact stated that the failure was predominant during cold weather. The vehicle was taken to the dealer, where it was diagnosed, and determined that the transmission sensor clusters had failed. The dealer reprogrammed the Powertrain Control Module and the Transmission Control Module. However, the failure persisted. The contact associated the failure with NHTSA Campaign Number: 16V529000 (POWER TRAIN); however, the VIN was not included. The manufacturer was made aware of the failure. The failure mileage was approximately 120,000.

I’m not sure but it will randomly die and have to be restarted there are times it does it more than others but every time is extremely dangerous because you essentially lose control of the car until it is restarted and it shift extremely hard sometimes like it feels like the transmission is going to fall out it jerks the entire car violently and there are numerous low voltage codes as well

Airbag light is on , 2nd time my lower control arms are broken and I go through a battery every 2 years average

The contact owns a 2015 Chrysler 200. The contact stated that while driving on several occasions at various speeds, the vehicle stalled. The power steering and battery warning lights were illuminated. The vehicle was restarted each time, but the vehicle took a progressively longer time to restart. Eventually, the vehicle failed to restart and was towed to an independent mechanic, where it was diagnosed and determined that the battery needed to be replaced. The vehicle was repaired, but the failure returned five minutes after driving off the lot. The vehicle was taken back, and it was determined that the wiring and electrical system had a communication fault, and that the vehicle needed to be taken to a dealer to be reprogrammed. The vehicle was towed to a dealer, where it was diagnosed, and it was determined that the battery cable and harness needed to be replaced. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 70,000.

You have a recall for chryslr 200 2015 for intermittent starting and stalling caused by faulty PDC connector. NHTSA. My car is doing exactly that but its not under the recall why not? It had done this gor the last 4 months

The transmission is stuck in 3rd gear and sometimes don't move at all. It has jumped in neutral a couple of times while driving or automatically goes to paddle shifting without touching the gear control. It is basically undrivable with only 95000, or so miles.

The contact owns a 2015 Chrysler 200. The contact stated that after the vehicle was started and shifted to park(P), the vehicle unexpectedly shifted into neutral(N), and the air bag warning light illuminated. The contact attempted to shift the gear selector into reverse; however, the vehicle remained in neutral. The contact stated that the vehicle could not be turned off. The contact disconnected the battery to turn off the vehicle. The dealer was contacted; however, the vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure. The approximate failure mileage was 138,000.

The contact owns a 2015 Chrysler 200. The contact stated that the vehicle failed to start. The engine warning light was illuminated prior to the failure. The failure persisted over time. The vehicle was taken to an independent mechanic who determined that the failure was related to the cruise control, transmission, and fuel pump. The local dealer was contacted, but the vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 180,000.

While driving at approximately 60 MPH on a highway, the vehicle suddenly lost motive power, stalled, and entered "limp mode," shifting into neutral or a low gear unexpectedly. This failure caused a rapid deceleration in high-speed traffic, effectively disabling the vehicle and creating an immediate safety hazard and risk of collision. The engine stalled completely, requiring the vehicle to be coasted to the emergency shoulder. After a key cycle, the vehicle restarted but the check engine light remained illuminated. Independent diagnostic scanning retrieved Diagnostic Trouble Codes (DTC) U0018 (Medium Speed CAN Communication Bus Short) and P0894 (Transmission Component Slipping). These specific codes and symptoms (intermittent electrical short causing stall/shift-to-neutral) are identical to the safety defects addressed in NHTSA Recall 15V-470 (FCA Recall R24 - Power Distribution Center Electrical Connector) and NHTSA 16V-529 (FCA Recall S55 - Transaxle Wiring Harness). Although records indicate Recall R24 was marked as "completed" on this vehicle in July 2015, the specific safety defect has recurred, presenting the exact same failure mode. The Authorized Dealer was contacted regarding the recurrence of this safety defect but refused to perform a no-charge inspection, citing an expired repair warranty. The Manufacturer (FCA US LLC) was also contacted to report the recurring safety failure but refused to open a case or authorize a diagnostic inspection, despite the life-threatening nature of the defect. The component and vehicle are available for inspection. The failure has not been resolved.

I put the car in park, once I released the brake the car started jerking forward. While this was going on, the dash displayed powertrain failure. I was only able to get it to stop by turning off the car. When I turned the car on following the event, I had a check engine code: P1B13-00 "Park-By-Wire-Unintended Out of Park Position". Since that incident, the car has excessive forward roll when putting the car in park. The shifting has become unpredictable and rough, it also gets stuck in 4th gear often. I took my car to a Chrysler dealership to see if it was in recall R08 / NHTSA 15V-090, I was told it was not and that I would have to pay for them to inspect it. My car was manufactured just before the recall window.

transmission service (power train ) caused my parking rod dislodged/broken to slip/jerk to lose control of vehicle. It had put us at high risk, no airbags didn't go off to causing passenger to hit their head blacking out and non-stop pain in rotating cuff of right shoulder. It was inspect by the police and city from not being drive-able to be towed and inspected by the towing/mechanical person. The messages that showed on dashboard was transmission failed/ services, engine light and having electrical issues to light was flicking once press on brakes. when idling to pulling off from a stop cause to jerk.

Queja de Defecto de Seguridad por Falla de TCM y Negligencia de Recall VIN del Vehículo: [XXX] Mi vehículo Chrysler 200, año 2015, ha experimentado una falla total del Módulo de Control de Transmisión (TCM), resultando en la pérdida abrupta de potencia e inmovilización de la unidad. Esta falla no solo es mecánica, sino que representa un peligro crítico para la seguridad, ya que puede ocurrir sin previo aviso en la carretera. Mi vehículo tiene 4 Recalls de seguridad obligatorios y pendientes (U90, W84, X80, XB1). El fabricante (Stellantis) se ha negado a resolver la falla del TCM y a atender los Recalls pendientes. A pesar de haber notificado formalmente a los departamentos de México (Caso No. XXX) y a los contactos corporativos en EE. UU., la compañía ha evadido la responsabilidad por más de 7 días. Tuve que pagar por un diagnóstico que confirmó la falla del TCM (Costo de reparaciónes y diagnostico estimado a la fecha: $35,496.00 MXN). Solicito a la NHTSA abrir una investigación sobre este defecto crítico de seguridad y la negligencia del fabricante en el cumplimiento de los Recalls federales. NOTA IMPORTANTE: MI DIRECCION DE CONTACTO REAL ES EN [XXX] . Municipio de [XXX] . C.P. [XXX] Celular: [XXX] Correo Electrónico: [XXX] Solo Hablo Español. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Chrysler sold me a unsafe rusted frame the car is dangerous and unsafe I'm scared of the car and it needs to be pick up

Somebody switch my vin to another car stolen the parts the car unsafe swaying and stole the shocks control arm sway bar air bag tampered my car had a key hole on the trunk when I bought it it not there the gas pedal break pedal no correct the car is dangerous and I have a stolen switched Chrysler under my vin number the metal tag missing out the windshield and not my engine

The contact called on behalf of the owner of a 2015 Chrysler 200. The contact stated that the owner received notification of Manufacturer Recall Numbers: U90 and W84. The contact stated that while driving 25 MPH, the vehicle failed to accelerate as intended while depressing the accelerator pedal. The vehicle stalled, and the contact pulled over to the side of the road. The dealer was contacted. The vehicle was left on the side of the road. However, the dealer refused to schedule an appointment to repair the vehicle. The manufacturer was not made aware of the issue. The failure mileage was approximately 127,000.

Hi My name is [XXX] I am submitting this form because on [XXX] My 2015 Chyler caught on fire on [XXX] in vidalia Louisiana I was leaving from where I live in Ferriday Louisiana that’s probably 10 minutes from where I Live I only had the car for 5 years I paid 22000 dollars for that car and every since I had that car I had problems I bought it from a deal ship in woodville Mississippi from a car lot called Wildcats I was over charge ..please help INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

This is my wife's account which happen more than 5-10 times because she operates the vehicle. The car at time's will jump into neutral while operating and the accelerator is unresponsive when she shifts back into drive. She cuts the car off for it to reset and sometimes it does, and sometimes she has to do it more than once. It sometime happens when the car has set for a while and she starts it, the transmission light will be on and the car will not move until reset.

The contact owns a 2015 Chrysler 200. The contact stated that while driving at slow speeds, the A/C failed to function as intended. The contact stated that when the A/C failed, the temperature gauge on the vehicle was elevated. The contact parked the vehicle, turned off the engine, and called a tow truck. The vehicle was towed to the residence, and then towed to the dealer. The contact was informed that the Power Distribution Center (PDC) electrical connector had failed, which caused intermittent power failures of certain electrical components. The contact was provided with an image of the fuse box, which showed that the fuse box was burnt. The contact was informed that the fan fire, PDC connector, and assembly needed to be replaced. The vehicle remained at the dealer pending the repair. The contact related the failure to NHTSA Campaign Number: 15V470000 ( ELECTRICAL SYSTEM); however, the VIN was not included. The manufacturer was not made aware of the failure. The failure mileage was approximately 147,000.

Safety Recall P43/NHTSA 14V-480 involves the 2015 Chrysler 200 with Driver One-Touch Power Windows built. Driver windows panel does not operate correctly and driver and passenger windows are inoperative due drivers front door wiring harness. The odometer also flashes while driving.

Friday, I was stuck in traffic when I noticed my temperature rising. I couldn’t pull to the side or turn my car off or do anything to get me safely out of the situation, my car then reached at what I last seen 275 degrees before shutting down. I had to leave my car setting as it was smoking and undrivable at this point. Later that night I got my car back home and upon further inspection my fan has abruptly stopped working, it is still getting voltage (bought a new fan) and that one also will not work either. When we checked the voltage it is backwards despite it never being worked on before. There’s electrical problems with these cars and they need addressed. I was left in 98 degree heat for almost 2 hours because of these issues. Next time it could be a woman and her children. Please fix this.

I’m writing to report a recurring issue with the catalytic converter on my vehicle. I had it replaced less than five years ago after the original one failed, which ultimately caused damage requiring a full engine replacement. Now, the replacement catalytic converter is failing again. I’ve owned my car for 11 years and have always taken good care of it. I find it extremely frustrating—and financially burdensome—to face potentially thousands of dollars in repairs again for what seems to be a recurring, possibly faulty issue. I’m requesting that Chrysler investigate this matter and provide assistance or a resolution, as this does not seem like normal wear and tear.