Chevrolet Malibu 2016 — Problemas reportados

It said service to stabilitrak press the gas and it won't go its delayed..

The contact owns a 2016 Chevrolet Malibu. The contact stated that while driving at 61 MPH, the vehicle unexpectedly began idling roughly. The contact stated that a loud noise was heard coming from the vehicle, and the cooling fan cycled on and off. The vehicle was taken to a service center, where it was found overheating. The cause of the failure could not be determined initially; however, the mechanic stated the failure was a known issue requiring a special diagnostic tool. Diagnosis revealed three piston rings leaking at 5 percent and the fourth piston ring leaking at 95 percent. The contact was informed that the piston rings could potentially be repaired if the necessary remedy parts were available for the model year. The failure mileage was approximately 66,000.

My vacuum pump has failed. Causing extremely dangerous driving conditions and potentially damaging my engine.

I believe my fuel pump was cracked

The contact owns a 2016 Chevrolet Malibu. The contact stated that while driving approximately 15 MPH and taking her children to school, there was an abnormally loud banging sound coming from the vehicle. The contact stated that several air bags deployed. The steering wheel air bag struck the contact, and she was knocked unconscious. The vehicle drove across the street and crashed into a divider. The vehicle was towed to the residence. The contact sustained minor bruises on the nose. Medical attention was provided by the emergency personnel on the ambulance. The manufacturer was contacted over the phone after the issue. A product allegation was filed, and the contact was informed there would be a response within four business days. The failure mileage was approximately 194,000.

2016 Chevrolet Malibu Hybrid LT 1.8L - current mileage 147,059 miles The factory exhaust heat exchanger failed internally, leaking engine coolant into the exhaust system. This caused check engine codes P0401 / P26BE, loss of cabin heat, coolant loss, and exhaust fumes entering cabin. GM has released 4 revisions of this part and all fail the same way, indicating known defective design. The part is currently on indefinite national backorder with no ETA from GM (Order #343585 from GMPartsNow on 08/22/2025 held without ship date). Dealers quote $1,587 and cannot obtain part either. This is a safety and emissions defect: coolant loss risks engine overheating, exhaust leak risks carbon monoxide in cabin, and coolant contaminates catalytic converter. GM discontinued Malibu Hybrid in 2019 without proper fix. This should be recalled. They produced a car, we bought it and now they don’t have the overpriced parts in stock to fix my car and when the parts is backordered, I keep driving it because i can’t work without my car which I very much need, the hybrid battery gets overheated, then they sell battery too and other damages too which will cost thousands to fix. This is a scam!

“Steering assist is reduced, drive with care” is showing up for a couple second and disappearing. When that happens my car seems to shut off and the steering wheel stiffens and pull to either the left of right side. All this happens while driving. After the 3rd time of it happening within 10min, my gas fuel level dropped but when back up to the “original” level

Rear steering knuckle and control arm knuckle.my car moves side to side. I have replaced everything in the rear end. I just recently bought this car.

Vacuum pump failure causing hard brake pedal which made near to impossible to brake safely and properly that lead to timing chain issues

The brake vacuum pump broke, causing my brakes to go rock hard and pieces fell down into the camshaft, causing engine damage

My car started overheating on my way home. I pulled over to find that there is a hole in my lower radiator hose, which was caused by the lower radiator hose being rubbed against the belt that is turned by the water pump. I had my wife and child bring me coolant on the side of the road where I was broken down. I eventually was able to get my car to my brothers but it required multiple stops and refilling of coolant. Once we got the car jacked up and the lower radiator hose replaced, we found the bottom of the radiator is loose and is pushing the lower radiator hose against the belt that rubbed the hole into the lower radiator hose. I then had my car towed to Dan Cummins in Georgetown Kentucky, located at 1470 Cherry Blossom Way, Georgetown, KY 40324. The mechanic drove my car that I had towed to the shop which damaged the new radiator hose that I had just put on the car. Dan Cummins of Georgetown Kentucky, who is an authorized Chevrolet Dealership, was informed (by me) that some 2016 Chevy Malibu's have been recalled because of a faulty lower radiator mount causing the lower radiator hose to push against the belt which causes the lower radiator hose to get a hole and leak. Dan Cummins suggested that I report my issue because my VIN is not covered by the recall. Authorized Chevy dealer Dan Cummins also suggested that I take my car elsewhere to be repaired while refusing to cover the damage they caused to the brand new lower radiator hose that I had purchased and put on the car. I would like for my Chevy Malibu with VIN [XXX] added to the recall so that I can have my Chevy Malibu repaired by an authorized Chevy dealership at no cost to me for something I did not do or cause. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The gear shift sometimes does read that it’s in park

I bought this car about 10 days ago. Throat was in pain, coughed up blood, dizzy, sweaty, and shaking. There's gas all over the ground coming from front under hood smelling through the vents. Very loud smelling. Took it to Chevrolet dealership on Covington hwy Decatur GA today and had to leave it there. I still don't feel good and neither the passengers in car. Car could've caught on fire gas leaking out when put in. Never experience this ever in my life. I may have to go to the hospital my chest feel very tight and I had a chronic asthmatic and my child in the car with me that's been on a breathing machine since last night and it's now 3:35 pm next day.

The vehicle is experiencing premature clear coat failure on the hood and roof. The affected areas show widespread oxidation, dulling, and breakdown of the clear coat, while vertical panels remain unaffected. This indicates failure limited to UV-exposed surfaces and does not appear to be normal wear. The condition is uniform across the panels and not caused by impact, chemicals, or improper maintenance. I have observed similar clear coat failure on other 2016 Chevrolet Malibu vehicles, suggesting a potential pattern or manufacturing defect affecting paint durability. The issue significantly impacts the vehicle’s exterior condition and resale value and continues to worsen over time. Photos are available documenting the condition.

On 04/28/2026, when diagnosing a reoccurring check engine light on the vehicle at a Chevy Certified Service, the mechanic "Borescoped cylinder 4 and found significant scuffs on the cylinder wall which along with the misfires indicate a cracked piston. The big picture appears to be the piston cracked which caused excessive oil consumption and misfires. The excess oil and unburned fuel overloaded the converter causing it to fail. The engine and converter will need to be replaced." In 2017, a recall was issued by GM to mitigate Stochastic Pre-Ignition (SPI) Causing Cracked Piston (17019). Between the initial purchase of the vehicle (11/2016) and performed service required by this recall (03/10/2017), there were approximately 5000 miles driven. No engine diagnosis was performed or recommended. After the 17019 was addressed, the engine misfires continued along with reoccurring CEL. C.S.P. N182195660 Predictive Monitoring for Stochastic Pre-ignition (SPI) released in 2019 states the 1.5 L LFV engines in certain 2016 and 2017 model year Chevrolet Malibu vehicles may have a preignition condition that requires immediate repair. This condition may cause the engine to perform poorly, misfire, run rough, and/or excessively consume oil. It may also illuminate the vehicle’s service engine light. Over time, if not repaired, the condition can damage the vehicle’s pistons and engine. The VIN for this Malibu was not attached to this notice despite it having SPI recall history. On 06/2023 (after the N182195660 program ended), at 80k miles a diagnosis revealed a potential cracked cylinder with no mention of the pre-ignition condition that could cause the crack, and the only way to fix is to replace the entire engine (as per dealer recomendation). Since vehicle was out of warranty, the repair est. was nearly $10k. I firmly believe my 2016 Malibu has suffered the consequences of poor mismanagement on this recall, and am demanding mitigation from GM to fix this issue.

The contact owns a 2016 Chevrolet Malibu. The contact stated that while driving approximately at 55 MPH in a rain storm and making a right turn, the ABS and Traction Control warning lights had illuminated, and the driver suddenly lost control of the steering and crashed into a tree. During the incident the driver sustained a concussion and neck and shoulder injuries which later required medical treatment. No police report was filed. The vehicle was later towed to the local mechanic. The cause of the failure was not determined. The manufacturer was notified of the failure, but no assistance was offered. The local dealer was not contacted. The failure mileage was 144,000.

Main seal leaking and engine needs replaced at 95,000 miles.

My car will rev up to 4000 rpm’s and my car will not go about 20 mph. My cruise stopped working after my car went into reduce engine power. The dealership said they fixed all issues but was back to doing the high rev within a week. It started this week telling me to shift to park even though my car was in park. The shift to park cable has been replaced twice now. I have been dealing with this since July of 2025. My car has been in the shop more times than I can count.

My car caught on fire under the hood. As I was driving on road I heard a sound and my car started slowing down and smoke started coming from under the hood got out the car not a minute later flames of smoke engulfed the car

Fuel Injector Backing ring Failing causing O-ring to dislodge and Rupture due to high pressure fuel leaking past the seal. This is causing a Major fire Hazard. Gm seal kits will not fix the problem do to Backer ring not being in the kit. part number for the o-ring kit is 12673056. this part should not be sold without the backer ring. if installed without the rings they will fail and will be Leaking fuel on the hot Cylinder next to the ignition coils. Misfire and bad fuel smell and possible no start or Fire!!

Have been getting reduced engine power since the summer on and off. Check engine light says its throttle bottle sensor and accelerator pedal position sensor. Which I was told there was a recall but my vin isn’t listed

I am reporting a recurring safety defect related to GM’s known “Shift to Park” issue. My vehicle displays a “Shift to Park” warning even when the vehicle is already in park, preventing the car from shutting off properly and creating a safety risk. This issue has been widely reported and associated with GM recalls and service bulletins. GM previously repaired this issue once while my vehicle was under warranty, acknowledging it as a known defect. The same defect has now reoccurred after the warranty period expired. GM is refusing to repair it again, despite the issue being recall-related and tied to a known defective design rather than wear and tear. This defect affects safe vehicle operation, risks battery drain, rollaway hazards, and driver distraction. I believe this is an unresolved safety defect that should be covered regardless of warranty status.

While driving, the vehicle experienced a mechanical failure involving the engine and lubrication system. Oil leakage was observed, and the engine began operating abnormally. This created a risk of sudden engine failure while the vehicle was in motion, which could result in loss of power, stalling, or loss of control, especially at highway speeds or in traffic. Prior to the failure, warning signs included abnormal engine behavior and fluid loss. The issue was not caused by driver error and occurred during normal operation. Continued operation in this condition presents a fire risk if oil contacts hot engine components. The problem has been inspected by a repair facility, and the failure appears to be related to a mechanical or manufacturing defect rather than wear or misuse. The component is available for inspection upon request. This defect poses a safety risk to the driver, passengers, and other motorists due to the possibility of sudden engine failure, loss of propulsion, or fire.

On December 16, 2025 the check engine light and service stabiltrek warning light appeared on my 2016 Chevy Malibu Hybrid. On December 17, 2015 I took the car the Capital Cheverolet service dept who has been servicing my car regularly for the past five years. They performed a complete diagnostics on my car that determined I need to "replace the EBCM with brake pressure modulator valve" and said it would cost over $2800.00. Upon further research I discovered that the same make model and year was recalled under recall #39440. I also learned the my VIN number was not included in this recall. This is a safety defect that has rendered my car not drivable until I get it fixed. As a senior citizen on a fixed income I am unable to fixed. I would like to know why was my car not included in the recall and if its possible to get it on the recall list so it can be fixed.

The vehicle went into shift to park and will not turn off. This is a known problem with ALL GM vehicles that hasn’t been fixed or offered a warranty for. It’s dangerous and causes the car not to move shut off in traffic and drains the battery. My car currently isn’t working due to this issue and the repair to fix is too much with no assistance from GM for a known defect. My car was almost hit because of the car had to be towed because it’s unable to be moved.

The contact owns a 2016 Chevrolet Malibu. The contact stated that while driving at an undisclosed speed, the accelerator pedal was depressed; however, the vehicle failed to accelerate. In addition, the vehicle occasionally accelerated independently. The contact stated that several unknown warning lights were illuminated, and the engine seized. The contact stated that the vehicle was jump-started daily, and the unknown warning lights turned off when the vehicle started. The vehicle was taken to the dealer; however, the failure was not duplicated. The vehicle was taken to several independent mechanics; however, the failure was not duplicated. In addition, the vehicle was taken back to the dealer where the vehicle was purchased; however, the failure was not duplicated. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The manufacturer was not made aware of the failure. The failure mileage was approximately 90,000.

My 2016 Malibu has a severe EBCM-related safety defect causing all four brakes to drag and overheat (reaching 240°F), leading to unstable handling. This condition mirrors the 2016 Malibu EBCM recall (GM Recall 39440). I sought help from GM. A GM-certified dealer-Monken in Centralia, IL performed a “diagnostic scan” which documented the core hydraulic failure: a constant, uncommanded 6.839 psi residual brake line pressure when the pedal was released. (A healthy system should be near 0 psi) This 6.839 psi is actively forcing the brakes to drag. The dealer ignored their own scientific data and submitted a fraudulent diagnosis of ("rust buildup") to GM, which GM used to deny the claim based on mileage. “Rust buildup” doesn’t create hydraulic pressure. GM is aware of this specific, documented, quantifiable safety defect (the 6.839 psi pressure) and is refusing to investigate it further. I stressed to GM that the vehicle wasn’t safe to drive and that I have a small child who has to ride in the car with me. GM dismissed my concerns by stating the dealership won’t release my car unless its safe to drive. I then had to drive the car 22 miles back home with all 4 brakes dragging. I requested the full diagnostic scan report (that the mechanic confirmed he could provide me with when I dropped my car off there) numerous times and never did I get one. I informed them that I would be filing a complaint hadn’t I received it by a certain time. The new kid in service then did send me screenshots of a generic OBDII scanner where I saw the 6.839 psi. I knew what the issue was prior to taking my car to Monken. I had an independent scan done prior. I only took the car there to comply with GM’s protocol to be eligible for assistance. I am requesting NHTSA investigate GM for failure to address a documented hydraulic control safety defect that causes brake dragging and overheating, which is non-compliant with safety standards. I can give further info Please call me for further details.

URGENT Complaint: NO RESPONSE to Demand for Rescission - Odometer Fraud, Deceptive Practices - Banner Ford of Monroe, LA

UNKNOWN While I'm driving my car will lose power and go into reduced engine power mode and slows me down to a crawl. I've almost been hit in the back many times for to this. The coffee is P2138

Check engine light comes on and dash says reduced engine power

Car suddenly stopped dead cold while driving on a highly driven road. No power. Several attempts were made to get off the main road and drive to a close neighborhood. Finally started and at every stop sign the car grinded during stopping and threw me backwards in driver's seat. Needed a tow. .

Engine to power is reduced. Poor fuel efficiency. Rough idling while parked. Poor acceleration. Trouble starting up. Burning smell at times.

The contact owns a 2016 Chevrolet Malibu. The contact stated that after driving and parking the vehicle, the contact entered the residence; however, upon returning to the vehicle, the vehicle failed to start. There were no warning lights illuminated. The vehicle was towed to the local dealer, and the contact was informed that the battery needed to be replaced. The battery was replaced. The vehicle was diagnosed, and determined that the camshaft, fuel vacuum pump, and camshaft sensor needed to be replaced. The Oxygen sensors were replaced. The vehicle was not repaired. The manufacturer was not contacted. The failure mileage was approximately 146,000.

The engine power reduced came light came on along with service stability trac. The car would stall after going into auto stop and just shut off. In certain instances it would shutoff when slowed down enough. It was brought in for service where the turbo charge solenoid starter and catalytic converter annd alternator all were replaced due to the turbo braking into pieces and being lodged into the converter and engine. Less than a week later the car returned to stalling at the auto stop feature. When brought in for service it was linked to the alternator and engine control module and mass air flow sensor. The car was then serviced again six months later for the alternator again. Now the car is once again stuck in engine power reduced with no direct codes linked to the problem and the starter was replaced and now the engine is remaining in limp mode. The car has stalled multiple times on not only at stop lights but on the highway and while turning at busy intersections causing traffic jams and even a side collision. The engine light as remained on since the day I got the car.

My 2016 Chevy Malibu Limited is experiencing Electronic Brake Control Module (EBCM) failure symptoms that match Recall 39440, even though my VIN is not listed in the recall. Details of the problem: -The brakes would randomly feel like they were sticking and the car being held back -Brake lights would remain on -Car would float all over the road -ABS and StabiliTrak warning lights illuminated in the dash once. -ABS and ESC functions stop working, leaving only based braking available. -These failures occur intermittently but increased to everytime. -All 4 brakes are dragging, pulsing (no lights illuminated), reaching 240 degrees -Confirmed by mechanic EBCM This is a safety hazard. The vehicle becomes more difficult to control in adverse conditions without ABS/ESC. I transport my special-needs child in this vehicle, and I am deeply concerned for our safety. Why I believe recall expansion is needed: GM has acknowledged this exact defect in Recall 39440 (affecting other 2016 Malibus built during specific production dates). My vehicle is showing the same failure, and I request NHTSA investigate whether the recall population should be expanded to include additional VINs.

My 2016 Chevrolet Malibu Limited (VIN: [XXX] ) experienced sudden loss of power while driving on 9/11/2025 and set code P228C. The dealership diagnosed the problem as the bolts coming loose from the high-pressure fuel pump, which caused the pump to detach from the cylinder head and become damaged, requiring replacement. This failure directly matches the defect described in NHTSA Recall 18V-358 (GM Campaign 18188/18268). That recall explains that the high-pressure fuel pump can detach from its mounting due to a weld failure, leading to oscillation, damage to the fuel system, and an increased risk of fire. Although the dealer phrased it as “bolts came loose,” the result is identical: the pump detached from the cylinder head and damaged the fuel system. Despite this, my VIN does not show an open recall. GM Customer Assistance told me the repair would not be covered because of the vehicle’s age and mileage (current mileage 129264), even though recalls are federal safety obligations that are not limited by warranty coverage. I am requesting that NHTSA review this exclusion and ensure Recall 18V-358 coverage applies to my vehicle. This defect creates a serious safety risk of fuel leaks and fire. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The high-pressure fuel pump detached from the cylinder head. The dealership confirmed diagnostic trouble code P228C and reported that one mounting bolt was missing and another bolt was broken off inside the cylinder head, causing the pump to come loose and fail. The damaged parts were replaced at my expense and the components are available for inspection if needed. This failure caused loss of engine power and unsafe drivability, putting my safety and the safety of others at risk. The problem was confirmed and documented by a Chevrolet dealer service center. General Motors has inspected the issue through their dealer network but has denied coverage because the vehicle’s VIN was not included in Recall 18V-18V-358, even though the failure matches that recall description. Warning symptoms included weeks of engine misfires, loss of performance, and eventually complete power loss while driving. These symptoms first appeared shortly before the failure occurred.

I own a 2016 Chevrolet Malibu (VIN: [XXX] , black, approx. 56,310 miles). The paint and clearcoat are failing prematurely, with peeling, cracking, and delamination appearing on the hood and roof panels. A repair estimate confirmed the need for full refinishing and corrosion protection to restore the exterior condition 2016 Chevrolet Malibu . This is not normal wear. The defect stems from faulty paint materials, defective clearcoat, or improper factory application. Although it manifests over time, GM knew or should have known of these issues but sold the Malibu without disclosure and refuses to provide assistance. The defect lowers the resale value, leaves the vehicle exposed to premature corrosion, and requires costly resanding and repainting. I respectfully request NHTSA investigate paint and clearcoat defects in the 2016 Chevrolet Malibu and determine whether a recall, service campaign, or consumer restitution is warranted. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

When I go down a hill the rpms jump up to 4, sometimes 5. I took the vehicle to the dealership and went on a drive, but no problem was determined. There was no warning lamps. To my knowledge, it started last year.

INTERMITTENT SHIFT TO PARK MESSAGE DISPLAYED WHILE VEHICLE IN PARK. TWO STATES HAVE SUED AND WON TO HAVE THIS SAFETY PROBLEM TAKEN CARE OF BY GM. (OHIO AND TENN.) SHOULD BE A RECALL ITEM. WHY NOT. GM SERVICE BULLETIN 19-NA-206, MARCH2024

Vehicle experiences a loss a power will driving. A lawsuit for defective throttle control and pedal position sensor was filed but eventually dismissed. GM is aware of the issue but has done nothing to fix it

Vehicle isn’t recognizing that it’s in park, shift to park keeps coming on dashboard which is also causing my vehicle not to change gears correctly

2016 Chevy Malibu is experiencing a “Shift to Park” issue, where the car does not recognize it is in Park even after shifting correctly. This prevents the vehicle from turning off, leaving lights and electronics running, which can drain the battery. A service advisor at AutoNation Chevrolet Orlando confirmed this is a common problem in GM vehicles like the Traverse and Silverado. She explained the repair—replacing the faulty sensor/shifter assembly—typically costs around $800. Beyond battery drain, there are safety concerns, since the system’s failure to recognize Park could risk the car rolling if the brakes disengage. The issue first appeared about four months ago, went away, and has now reoccurred.

The fuel pressure system is faulty and shutting the engine down and reducing speed