BMW X7 2020 — Problemas relatados

Front differential failed at ~79,000 miles. Regular service intervals and BMW specific oil were followed throughout the life of the vehicle. The pinion bearing began to wear prematurely which resulted in gear damage on a ring/pinion from metallic fragment introduction into the compartment.

The vehicle suffered a complete premature failure of the factory aluminum A/C evaporator core due to internal corrosion. This is a known, widespread issue on BMW G-chassis vehicles. The failure causes pressurized R-1234yf chemical refrigerant and atomized PAG compressor oil to leak directly into the passenger cabin ventilation stream, creating a health hazard from chemical fumes. Additionally, the complete loss of climate control dehumidification causes immediate, severe windshield fogging during inclement weather, creating a sudden and significant visibility hazard while driving. A formal diagnostic by a BMW dealership confirmed the leak and estimated the repair cost at $7,600.

2020 bmw x7 with 34k miles 1 driver, front suspension control arm leaking causing clunk and un even steering / braking feel due to premature leaking of the hydraulic fluid do to a design flaw. As a 40 Honda master tech and 30yr dealer principal I cant believe bmw will not warranty this defect or up grade the part as it seems its still used today and thousands have complained about the issue not even to mention the car is 95k new totally unexceptable. Thank you, [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Approximately 67,000 miles, my 2020 BMW X7 XDrive 40i began falsely indicating that the driver's door was open even though the door was securely closed. While the vehicle was in drive and moving, the false door open signal caused the vehicle to automatically shift into park and abruptly react. This caused a serious risk of an unexpected stop and loss of vehicle control. BMW Fairfax inspected the vehicle and verified that it indicated the driver's door was open and shifted or attempted to shift into park while driving and moving. BMW found fault code 804168 relating to the driver door contact circuit and reported that the fault had occurred more than 53 times. BMW also found multiple invalid signal faults and loss of communication with the body domain controller. At approximately the same time, the vehicle displayed chassis malfunction and parking assistant malfunction warnings. The vehicle also has an ongoing water intrusion problem involving the panoramic roof, including water entering the passenger compartment. It's not yet known whether the water intrusion contributed to the electrical and communication faults. Additionally, there have been multiple issues with the rear sunroof not working properly and noises happening when the front sunroof is opened. BMW is recommending replacing the driver door actuator and attempting to program the body domain controller with a possible BDC replacement if programming is unsuccessful. The safety condition has not yet been repaired or conclusively resolved. There was no crash or injury. I'm reporting this because an erroneous door open signal that causes a moving vehicle to shift or attempt to shift and depart could result in sudden deceleration, loss of control, or collision.

We came from [XXX] to [XXX] at night. It was rainy in [XXX]. We parked the vehicle in the front of the garage door of the house and went to sleep. Around 8:00-9:00AM two police cars from [XXX] PD came to our house. The officer said that the vehicle calls to BMW or 911 as an emergency and they forwarder that call to FPD. The officers checked the vehicle and they figured that the vehicle did the emergency call when was parked. Now, the emergency call system is not working, because of the bad factory sealant in the top of the roof and the water leaks exactly to the Telecomunication module (TCM). INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Low oil sensor continues to light up and says i am low on oil. Found out that my oil pump was the main cause of the issue. At this time I have to have the oil pump replaced. It was also determined there have been numerous reports regarding oil pump failure in the 2020 BMW x7 due to an internal plastic part.

The front thrust arm bushing was previously replaced on December 19, 2023, at 34,750 miles (after three years of ownership). It has now failed again at 57,203 miles, lasting only about 22,500 miles. This repeat failure within a relatively short timeframe and mileage interval suggests an underlying issue or defective part. The dealer wants me to replace both Front Thrust Arm bushings again.

My X7’s front differential went bad at 50k miles. I paid over 100k for a vehicle of this caliber to have something like this fail and have to pay 8k with no help from BMWNA. I’ve been a loyal customer with bmw having owned over 5 bmw vehicles in the past. And for me to get treated like this is unacceptable. I hope we can have a law suit against bmw for this.

While driving the vehicle sensor lights began to come on. I assumed it was a dirty outside sensor. Not long after the ABS system lit up and my car said traction even though I was just pulling into my driveway. I quickly turned around and drove to my mechanic. Showed him all the lights and he connected the computer to read the error codes. Found out that my oil pump was the main cause of the issue. Double checked to make sure it wasn't a battery failure causing incorrect error codes and the battery was in good condition. At this time I have to have the oil pump replaced. It was also determined there have been numerous reports regarding oil pump failure in the 2020 BMW x7 due to an internal plastic part.

I am writing to formally report a potential safety-related defect involving BMW vehicles equipped with the B58TU engine, primarily affecting model years 2019 through 2021. My vehicle experienced a sudden loss of engine oil pressure that resulted in catastrophic engine failure. This condition occurred with little to no warning and led to immediate vehicle disablement. The failure created a hazardous situation, as the vehicle was no longer able to maintain propulsion and could have placed occupants at risk because it occurred in active traffic or unsafe conditions. Based on my experience and additional research, the issue appears to originate from the engine’s oil pump design. Specifically, the oil pump contains an internal pressure-regulating component originally manufactured from plastic. This component is prone to fracturing, particularly during cold starts or low ambient temperatures. When this failure occurs, oil pressure becomes erratic or is lost entirely, often without sufficient warning to prevent engine damage or vehicle shutdown. My vehicle had this occur on January 20th 2026, as it was 5 Degrees outside. I suddenly lost oil pressure and had my vehicle’s engine catastrophically fail on a highway with my two small children ages (3) and (7 months) in the vehicle. In some cases, drivers may observe warning signs such as inability to measure oil level electronically, abnormal oil pressure readings, or drivetrain malfunction warnings. However, these indicators are inconsistent and often appear only moments before complete failure, leaving insufficient time for corrective action. This issue represents a significant safety concern for the following reasons: * Sudden loss of oil pressure can result in immediate engine shutdown or loss of propulsion while driving * Failures frequently occur under predictable conditions (cold starts in low temperatures), indicating a repeatable defect * Drivers are not provided with adequate warning to safely respond before damage.

NHTSA COMPLAINT (VERY IMPORTANT – SAFETY FOCUSED) Subject: Safety Complaint – BMW X7 Electrical Defect and Fire Risk (VIN: [XXX] ) To the National Highway Traffic Safety Administration, I am submitting a formal safety complaint regarding a 2020 BMW X7 xDrive40i affected by Recall No. 24V-576 (Engine Starter Defect). My vehicle has experienced: •Sudden battery failure •Electrical system malfunction •Starter-related issues consistent with recall description BMW’s recall states that the defect can cause: •Electrical overload •Starter overheating •Increased risk of engine compartment fire This is not a theoretical issue—I have already experienced a complete system failure requiring towing and major repair, placing my family and me at risk. Serious Concerns •The defect appears systemic and dangerous •The remedy (software update) does not appear sufficient •The failure occurred without adequate warning Request for Investigation I urge NHTSA to: 1.Investigate the effectiveness of BMW’s recall remedy 2.Determine whether additional defects exist in the electrical system 3.Ensure BMW provides a permanent and safe solution This issue poses a serious public safety risk, and stronger regulatory action may be necessary. Sincerely, DLAA REAL ESTATE INVESTMENT, LLC, [XXX] and [XXX] ), regarding the defective BMW, YEAR 2020, MODEL: X7 xDrive40i | COLOR: OC27 ARCTIC GREY METALLIC VIN: [XXX] | CELL: [XXX] | FAX: [XXX] [XXX] | [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

I'm reporting a safety issue with BMW vehicles equipped with the B58TU engine, primarily 2019-2021 models. These vehicles have an oil pump with an internal plastic component that regulates oil pressure, and this part is fracturing in the field, causing sudden loss of oil pressure. The failure typically occurs during cold starts in low temperatures. When it fails, oil pressure becomes erratic or is lost entirely, often with little to no warning before engine damage or vehicle disablement. Warning signs, when present, include inability to measure oil level electronically, abnormal oil pressure, or sudden drivetrain malfunction warnings. These can rapidly progress to engine shutdown or severe damage from oil starvation. This creates a dangerous situation because the vehicle can become disabled without warning while driving or after startup. This is especially hazardous when cars become immobilized in traffic or during winter conditions when failures occur most frequently, leaving occupants exposed to freezing temperatures while awaiting assistance. Pump replacement requires extensive disassembly and commonly costs $6,000-$8,000, assuming no engine damage. A critical concern: owners cannot determine if their vehicle has the original plastic pump or the later metal revision. BMW's VIN-based parts lookup now shows updated components even when original plastic parts remain installed, and BMW has removed the original plastic part number from dealer networks entirely. Failures are reported across multiple production years, and the scope of affected vehicles remains unclear. Because this condition causes sudden vehicle disablement without adequate warning, especially in cold weather, I believe this warrants investigation as a potential safety-related defect.

The transfer case on my 2020 BMW X7 failed and had to be replaced. Turning the vehicle became unstable as the vehicle shuttered badly. BMW confirmed the shuttering and first changed the transfer case fluid. However, it only slightly helped at first but the shuttering came fully back shortly thereafter. The vehicle was inspected by BMW twice. I don’t remember any warning lights on the dash. The shuttering first occurred in 2024.

Oil pum with plastic internals. Repeat hot and cold cycles cause premature failure of the plastic components and cause loss of oil pressure along with the pump grenading itself.

Transfer case broke and struck the engine while driving.

My vehicle is included in BMW Recall Campaign No. 25V 644 – Engine Starter. It has repeatedly failed to start, and on two separate occasions the engine completely stalled while I was stopped at a traffic light. Each time, it took multiple attempts before the car would restart. I have also been stranded in numerous parking lots—during both extreme heat and freezing temperatures—with my children because the vehicle would not start. These incidents were unexpected, unsafe, and entirely consistent with the symptoms described in the recall. We have experienced these problems since purchasing the vehicle, but at the time we had no reason to believe we needed to document every occurrence. Now that BMW has acknowledged a fire risk defect and still has no available remedy, I do not feel safe continuing to operate this car. BMW has even advised owners not to park in a garage due to the potential fire hazard. The first recall was issued in 2024 and did not resolve the issue. The subsequent recall in August 2025 still has no fix. This ongoing situation presents a serious safety risk, and it is unacceptable that it remains unresolved. BMW should be buying these vehicles back and compensating owners for the significant inconvenience and danger this defect has caused.

The check engine light on my 2020 BMW X7 intermittently illuminates and then clears without warning. A BMW technician diagnosed the cause as a malfunctioning active grille shutter assembly at the front of the vehicle. Research shows this is a widespread issue among BMW X5 and X7 models of similar years, with many owners reporting the same failure and expensive repairs. This appears to be a systemic defect, not an isolated incident. Because the grille shutter directly affects engine airflow and cooling, this issue raises reliability and potential safety concerns and should be reviewed for a possible recall.

Low oil pressure warning. Oil pump replacement

The contact owns a 2020 BMW X7. The contact received notification of NHTSA Campaign Number: 25V644000 (Electrical System). The contact stated that while driving at an undisclosed speed and making a left turn, the vehicle stalled in the middle of traffic. The contact immediately depressed the brake and attempted to shift into park(P), but the transmission failed to respond as needed. The contact remained in the vehicle with the brake pedal depressed until Roadside Assistance arrived. The contact stated that the Roadside Assistance team held the start button down and the gear selector was shifted into neutral(N) for a second and continued to inadvertently shift back to park(P). The vehicle was towed to an independent mechanic who was unable to properly diagnose the vehicle and referred the contact to the dealer. The vehicle was then towed to the dealer, where it was diagnosed and determined that the starter needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was approximately 85,600.

• Third-row seat in my 2020 BMW X7 failed during normal operation and trapped my [XXX] daughter between the seatbacks. • She sustained injuries to her legs (documented in photos). I injured my arm while trying to free her. • Approximately 10 people witnessed the incident. • Seat would not move or release electronically or manually—no functional emergency release. • Multiple BMW system warnings occurred before the incident, including:  – “Third row seat risk of injury”  – “Right/left rear seat unlocked”  – “Right/left rear seat back unlocked” • BMW’s inspection found the passenger-side third-row seat motor housing broken. • There was no misuse and the failure occurred during normal operation • BMW refuses to repair the defect under warranty and attempted to return the vehicle unrepaired. • BMW suggested an “outside influence,” but evidence does not support this. • This defect creates a serious entrapment and injury hazard with no reliable manual release. • Requesting NHTSA investigation into BMW X7 third-row seat motors, locking mechanisms, and lack of emergency release due to risk of occupant injury or inability to evacuate a trapped passenger. There is an open and unresolved case with the manufacturer. Please help us and others that may be in danger. We still don’t have our vehicle back after 6 weeks and they state they will not fix it and return it to us broken, unsafe, and not usable. Here is the contact at BMW Gabrielle Dorcean Executive Customer Care, Customer Relations and Services BMW of North America, LLC Phone: [XXX] [XXX] Email: gabrielle.dorcean@bmwgroup.com INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

I am filing this complaint because the third-row passenger seat in my 2020 BMW X7 has a serious defect that poses an immediate safety risk to children and passengers. The third-row seat malfunctioned while my child was exiting the vehicle. The powered seat began moving unexpectedly and trapped my child’s leg, and we had extreme difficulty getting the seat to release. This is an extremely dangerous failure for any powered seat, especially one that is frequently used by children. This is not normal wear and tear — this is a mechanical and electrical failure of a safety-critical seat system. BMW Fresno has had the vehicle for more than six weeks and cannot fix the problem. BMW North America reviewed the case but denied responsibility and closed it, even though the defect affects a powered safety-critical seat. We still have no repair, no explanation, and no assurance that the seat is safe. I am filing this because the powered seat poses a clear risk of injury, and BMW has not resolved or acknowledged the safety defect. I request that NHTSA investigate the 2020 BMW X7 third-row seat system for potential entrapment hazards. Actions Taken •BMW Fresno inspected the vehicle and kept it for 6+ weeks. •BMW NA conducted a review but has refused to cover cost of repair or acknowledge a defect. •I am seeking NHTSA’s involvement because this is a clear safety problem that BMW has not corrected.

Hello , I would like to report a failed front differential on my vehicle. This issue was diagnosed by an independent BMW shop and is currently being repaired. Mine made it to 69k miles but many others have had theirs failed before 50k miles. My main goal is to bring light to this issue since it seems to be a design flaw. There's also numerous reports for failed transfer cases since they aren't normally serviced by BMW dealers. I've attached both repair invoices.

My front differential has failed and my vehicle has 62,000 miles. There is no recommended service and maintenance schedule for replacing fluids for the front differential so I thinking that this failure is due to an engineering design flaw including no recommended schedule to service the unit. It also seems this component may be too small/weak for the engine output. I has seem this failure reported on many blobs and users groups and seems to be recurring issue that BMW turns a blind side to. They ask why an extended warranty was not purchased and seeing that this is a recurring problem I am asking for a possible recall to force BMW to pay or reimburse others for repairs.

The contact owns a 2020 BMW X7. The contact stated that while driving at an undisclosed speed, there was an abnormal sound coming from the wheels while turning to the right or the left. No warning lights were illuminated. The vehicle was taken to the dealer, where it was diagnosed that both front control arms needed to be replaced; however, the vehicle was not repaired due to the cost. Upon investigation, the contact related the failure to NHTSA Campaign Number: 20V678000 (SUSPENSION); however, the VIN was not included. The vehicle was previously serviced under NHTSA Campaign Number: 25V644000 (ELECTRICAL SYSTEM). The manufacturer was not made aware of the failure. The failure mileage was approximately 42,000.

The contact works for a company that owns a 2020 BMW X7. The contact stated that while his boss was driving at an undisclosed speed, the vehicle stalled. The driver was able to veer to the side of the road. The vehicle was towed to a station. The vehicle was then towed to the dealer, where it was diagnosed and determined that the front trans-axle had disintegrated, causing the shaft to pinch and to create an 8-inch hole at the bottom of the oil pan. The contact stated that a significant amount of oil had leaked from the vehicle. The dealer determined that the transmission and engine had failed and needed to be replaced. The dealer informed the contact that it was a known failure, but the vehicle failure was the most dangerous reported failure. The vehicle was not repaired. The manufacturer was notified of the failure and informed the contact that no assistance could be provided because the VIN was not included in a related recall. The failure mileage was approximately 140,218.

The contact owns a 2020 BMW X7. The contact stated that while driving at 55 MPH, the vehicle lost motive power, with the check engine warning light illuminated. The vehicle was towed to the dealer, where it was diagnosed, and determined that the fuel pump module had failed and needed to be replaced. The vehicle was repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 50,000.

Transfer case causes vehicle to shake when driving straight or turning from a complete stop or low speeds.

X7 models from year 2020 -2022 have a particular issue at stake which is a manufacture default as it's been reported in many cases in X7 models. I'd like have this Transportation safety to please look into this issue a safety recall as there is a shuddering issue in most x7's when turning right or left at a lower speed which slips the vehicle. I would appreciate it if someone could look into this. Thanks,

The contact owns 2020 BMW X7. The contact stated while driving 30 MPH, the message "Oil Pump Leak Over - Get the Vehicle Towed to Local Service Dealer" was displayed. The vehicle was towed to an independent mechanic, who could not repair the vehicle. The vehicle was towed to the dealer, where an unknown diagnosis was made. The vehicle was then towed to Baltimore Motor Works, where it was diagnosed that the engine oil pump had failed and needed to be replaced. The vehicle was repaired. The manufacturer was notified of the failure, but no assistance was provided. The contact was referred to the NHTSA Hotline to report the failure. The failure mileage was 60,000.

I was driving and as I parked on my driveway a message popped up on my dash board saying " " Increased Steering efforts" then I wasn't able to move the steering wheel at all, it feel like it got locked.

I am submitting this complaint based on recurring drivetrain and structural failures in my 2020 BMW X7 (VIN: [XXX] ), which raise serious concerns about reliability and safety. Most recently, the vehicle exhibited shuddering, power loss, and a “neutral-like” disengagement at low speeds. BMW of Pembroke Pines confirmed this through a test drive. However, instead of mechanical replacement, the dealer performed a VTG oil flush and attempted a calibration, which—according to their own documentation—“lost connection.” These signs point to recurring issues with the ATC (transfer case), a known point of failure in several BMW X models. Additional manufacturer defects I’ve experienced include: - Two incidents of cabin water intrusion from separate leaks - A dashboard panel burst shortly after purchase - Rear seat failure requiring a $7,000+ repair BMW North America refuses to provide further assistance despite acknowledging the repair history. This leaves me with a potentially unsafe vehicle, prone to recurring drivetrain failure without a clearly defined remedy. I respectfully request that NHTSA investigate whether the Active Transfer Case and related VTG components in the BMW X7 pose a defect trend requiring formal attention. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

While my wife was driving our 2020 BMW X7M under normal conditions, the vehicle experienced a catastrophic drivetrain and differential failure. According to the BMW dealership’s service manager, internal drivetrain components became disconnected while the vehicle was in motion. This caused parts to spin freely and damage surrounding systems. Fortunately, no crash occurred, but the technician emphasized that it could have easily led to an accident. There was no external impact, accident, or driver error. Both the BMW dealership and an independent insurance adjuster from GEICO confirmed the failure appeared to be mechanical and internal in nature, possibly due to a manufacturing defect. This failure poses a significant safety risk to occupants and other drivers. Had it occurred at higher speeds or in traffic, the consequences could have been severe. I believe this incident warrants investigation due to potential systemic safety concerns. I am requesting that NHTSA review this failure for manufacturer defects and evaluate whether similar complaints exist regarding drivetrain integrity in BMW X7M models. Supporting documentation, including video evidence, dealership notes, and the insurance report, are available via this link [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The contact owns a 2020 BMW X7. The contact stated that while attempting to start the vehicle, the engine failed to turn over. The message "Starter Motor Overheating" was displayed; however, there was no warning light illuminated. The vehicle was towed to a local dealer where it was diagnosed, and the contact was advised that the starter motor and battery were faulty and needed to be replaced. The contact was also advised that the coolant needed to be drained and refilled. The vehicle was not repaired. The contact referenced NHTSA Campaign Number: 24V576000 (ELECTRICAL SYSTEM, ENGINE AND ENGINE COOLING); as a possible cause for the failure. The manufacturer was notified of the failure. The approximate failure mileage was 58,000.

Without warning the vehicle came to an abrupt stop while going about 25 mph. I got out and checked and noticed a liquid dripping from underneath the front area of the vehicle. Later determined it was the front transfer case. I really would hate to think what could have happened at higher speeds. Again, no warning at all.

The contact owns a 2020 BMW X7. The contact stated that after parking and later attempting to start the vehicle, the message "Starting Engine Possible After Engine Overheat" was displayed, and the vehicle failed to start. The contact waited several hours before the vehicle was able to be restarted. The vehicle was driven to the local mechanic who diagnosed that the starter had overheated. The vehicle was later taken to the local dealer who diagnosed that the starter module was faulty and needed to be replaced. The vehicle was not yet repaired. The manufacturer was notified of the failure, but no assistance was offered. The contact stated that the vehicle was previously serviced under NHTSA Campaign Number: 24V576000 (ELECTRICAL SYSTEM, ENGINE AND ENGINE COOLING) which required a software update. The contact stated that the vehicle had experienced the failure listed in the recall after the recall repair was performed. The failure mileage was 44,000.

Third row seat malfunction sending rear seat back unlocked appearing on dash. Switch for third row seat is faulty and need to be replaced. Warning states a safety issue with seat being unlocked. Inspected by bmw passport. The notice came up 3 days ago on dash vehicle was purchased from global auto outlet 12/26/24

I have noticed that the engine light on my BMW X7 keeps turning on after long rides but then disappears after some time. Upon inspection, I was informed that the issue is related to the active grille shutter, which is located in the front part of the body. While researching to see if others have experienced the same issue, I discovered that many BMW X5 and X7 owners have reported similar problems. It appears to be a common issue with these models. I believe BMW should consider issuing a recall for this problem since it seems to affect a significant number of vehicles in this range.

On August 1st 2024, NHTSA initiated campaign number 24V576000, BMW "Starter Motor May Fail and Overheat". On 10/3 I went into BMW of Bloomfield to get an oil change & address the recall. On 11/23, my car would not start in the middle of traffic. Then on 11/25 I brought in my 2020 X7 to ascertain why the car stopped working and have it fixed. I was told by BMW that the same starter motor stopped working. When I received a call stating that the car was fixed, I informed them that this should be covered by BMW as it was a direct result of the recall that should have been addressed back in October. I'm currently waiting for BMW NA to pay for the failed recalled part, case 07650216.

The car just stopped in the middle of the road and wouldn’t restart. The starter is fried. I didn’t know about the starter recall

The failed component was observed when the Restraint warning icon appeared. There was no accident because the vehicle was taken to the BMW dealership for investigation. There is a warning not to drive because the Restraint system may not work properly. This is a safety issue with no work around to operate the vehicle in a safe manner. After reviewing multiple threads online, it appears that my situation is not uncommon with BMW. I took the vehicle to BMW service and they confirmed there is a fault in the harness that allows the airbag, seat belt and tensioner to not operate properly in the case of a collision. The service advisor admitted they have seen this before and knew how to repair it. The repair is too costly to investigate the harness where the defect in the wiring occurred, so the opt to replace the harness in a parallel manner, which still takes 7 hours and over $2200. The vehicle is only a few months out of warranty and has less than 18,000 total miles. They is no way that the harness experienced normal wear over the years to cause this with such low miles. They attempted to blame the Arizona heat as possible cause, but the vehicle was in Illinois to 2 of the 4 years and while in Arizona, it is parked in my air conditioned garage. Heat is not the cause. This situation is a design defect during assembly or a defective harness at manufacturer. BMW would not accept any responsibility for the issue, which is a safety liability to passengers.

I was driving on the freeway when due to heavy traffic, it was a stop and go. the engine stalled and on re-started on multiple trials. this created a very dangerous situation for an immediate accident as there were vehicles all around me. the engine stalling continued the next day also and I took my vehicle to BMW for servicing and they diagnosed engine starter motor failure which they then replaced and charged me $1,411.44 on June 27, 2024. NHTSA has issued the following recall stating that the starter motor may fail and overheat. NHTSA Campaign Number: 24V576000 Manufacturer BMW of North America, LLC Components ELECTRICAL SYSTEM, ENGINE AND ENGINE COOLING [XXX] I called BMW customer service and they told me that my vehicle VIN number was not on the affected vehicles list and hence, they can't do anything and that I should make a complaint with NHTSA. since the issue with NHTSA recall was starter motor on BMW and since I had to pay to get it replaced before NHTSA issued the recall, I strongly feel that BMW sold the car with a faulty starter motor and that they should reimburse me for my out of pocket expenses to get the stater motor replaced. Please advise. thanks, [XXX] , Tel: [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

While driving the sunshade for the moonroof opens by itself. I try to close it but it takes about a minute before the button to work and then it does it again. Around 3 times in a row. I did not take it to dealer yet since it is out of warranty. It is very distracting while driving and this happens