BMW X5 2020 — Problemas reportados

While driving home vehicle began to smoke. Pulled over thinking it may be overheating, not realizing it was smoke. No warnings or messages were displayed. Parked, turned off ignition and called husband from vehicle. When smoke became overwhelming I got out of vehicle. Noticed sparks dripping from under vehicle. Called 911 as sparks became a fire. Entire engine was engulfed in flames as fire department arrived. Police arrived on scene and vehicle was towed and inspected the following day by Geico who declared vehicle a total loss.

The contact owns a 2020 BMW X5. The contact stated that while driving, the ignition switch message was displayed. The contact stated that later in the day, while driving at an undisclosed speed, the brake pedal was depressed, and the brake malfunction message displayed. The contact forcefully depressed the brake pedal to stop the vehicle. The vehicle was parked and turned off. The vehicle was restarted. The contact stated that several unknown warning lights were illuminated. The dealer was contacted by phone and made aware of the failure. The vehicle was taken to the dealer, where it was diagnosed with a brake master cylinder reservoir failure. The contact was informed that the brake master cylinder reservoir needed to be replaced. The contact referenced NHTSA Campaign Number: 21V062000 (Service Brakes, Hydraulic); however, the VIN was not associated with the recall. The manufacturer was contacted by phone, and a case was filed. The contact was informed that the failure was regular wear and tear. The failure mileage was approximately 99,000.

I am reporting a severe structural safety failure on my 2020 BMW X5. While driving, the front suspension assembly suffered an abrupt mechanical failure. A subsequent inspection by an independent service facility revealed that the front control arm brackets had "burst" / fractured. This exact mechanical failure perfectly mirrors NHTSA Campaign Number 20V678000 (issued for 2020–2021 BMW X5 vehicles), which states that the weld connecting the front axle support to the right front control arm bearing bracket can fail and separate, resulting in a loss of steering control. Despite suffering from the identical, dangerous structural defect outlined in the federal recall, my specific VIN was excluded from BMW's active recall campaign. I had to pay out-of-pocket for an independent repair to make the vehicle safe to drive. I have attached the itemized mechanic's receipt explicitly stating "front control arm brackets burst" as empirical evidence. I request that the NHTSA investigate whether BMW's recall scope for this weld defect needs to be expanded to include omitted VINs.

See attached document for complaint.

My 2020 BMW X5 sDrive40i has experienced recurring and serious electrical, shutdown, and drivability problems that have not been resolved despite BMW service and a recall-related repair. The vehicle has unexpectedly restarted after being turned off and has also failed to shut down properly. On September 6, 2026, after being parked at Costco for approximately 40–60 minutes, I returned to find the vehicle off but not secured. The brake lights were on, the windows were down even though I had left them up, and the interior systems were operating. The radio was playing an unfamiliar station, although I do not listen to the radio. I documented this on video. Later that same day at Whole Foods, after parking, turning the vehicle off, and getting out to retrieve my dogs, the vehicle appeared to still be running. Video captured the engine running for approximately one second. I shut it off and locked it, but the vehicle then unlocked itself, also captured on video. These were two separate incidents within nine days, occurring after BMW performed a recall-related repair intended to address unexpected vehicle reactivation. In addition, the vehicle has twice shut off unexpectedly while accelerating on the freeway. These incidents, combined with the unexpected restarting, failure to shut down, windows opening, and vehicle unlocking itself, create serious safety concerns. I purchased this vehicle specifically to transport my dogs. If the vehicle can unlock itself or lower the windows while I am away, my dogs could escape or be exposed to being taken. I no longer have confidence that the vehicle will remain safely shut down and secured when I leave it. The recurring nature of these failures and the fact that they have continued after BMW’s attempted repair require a thorough investigation and permanent resolution. I am requesting that BMW review the complete history and consider repurchase or replacement if the defect cannot be permanently corrected.

I'm reporting a safety issue with BMW vehicles equipped with the B58TU engine, primarily 2019-2021 models. These vehicles have an oil pump with an internal plastic component that regulates oil pressure, and this part is fracturing in the field, causing sudden loss of oil pressure. The failure typically occurs during cold starts in low temperatures. When it fails, oil pressure becomes erratic or is lost entirely, often with little to no warning before engine damage or vehicle disablement. Warning signs, when present, include inability to measure oil level electronically, abnormal oil pressure, or sudden drivetrain malfunction warnings. These can rapidly progress to engine shutdown or severe damage from oil starvation. This creates a dangerous situation because the vehicle can become disabled without warning while driving or after startup. This is especially hazardous when cars become immobilized in traffic or during winter conditions when failures occur most frequently, leaving occupants exposed to freezing temperatures while awaiting assistance. Pump replacement requires extensive disassembly and commonly costs 6,000-8,000, assuming no engine damage. A critical concern: owners cannot determine if their vehicle has the original plastic pump or the later metal revision. BMW's VIN-based parts lookup now shows updated components even when original plastic parts remain installed, and BMW has removed the original plastic part number from dealer networks entirely. Failures are reported across multiple production years, and the scope of affected vehicles remains unclear. Because this condition causes sudden vehicle disablement without adequate warning, especially in cold weather, I believe this warrants investigation as a potential safety-related defect.

I am reporting a safety concern involving BMW vehicles equipped with the B58 Technical Update (B58TU) engine, commonly found in model years 2019–2021. These vehicles utilize a variable-displacement engine oil pump containing an internal thermoplastic adjusting component responsible for regulating engine oil pressure. Failures have been reported in which this internal plastic component fractures, resulting in sudden loss of or instability in engine oil pressure. My own vehicle has experienced this oil pump failure. The failure is particularly concerning because it can occur during cold-start operation and appears to be more prevalent in low ambient temperatures. When the internal component fails, oil pressure regulation can become erratic or be lost entirely. The resulting loss of lubrication can lead to severe engine damage or vehicle disablement. Reported precursor symptoms include an inability to electronically measure the engine oil level, abnormal oil-pressure behavior, drivetrain malfunction warnings, and other warning messages. However, these symptoms may provide little meaningful advance warning before the vehicle becomes disabled or the engine sustains significant damage. The safety concern is not limited to the cost of the repair. A sudden loss of oil pressure can cause the vehicle to become disabled without warning while driving or shortly after startup. This presents a potential safety hazard if the vehicle loses power or becomes immobilized in active traffic. The risk is particularly concerning during cold-weather operation, when these failures appear to occur most frequently. In winter conditions, occupants of a disabled vehicle may also be exposed to freezing temperatures while waiting for roadside assistance. Replacement of the oil pump is a major repair with cost ranging $6000-8000, even when engine has not been damaged. These costs are secondary to the safety concern but demonstrate the seriousness of the defect and the potential severity.

I am reporting a safety concern involving BMW vehicles with the B58TU engine, model years 2019-2021. These engines use a variable-displacement oil pump with an internal thermoplastic adjusting ring that regulates oil pressure. Field failures are being reported in which this component fractures, causing sudden loss or instability of oil pressure. Owners and independent shops report catastrophic engine damage within minutes, with little or no advance warning. A sudden loss of motive power at highway speed, or an engine seizure in traffic, creates a crash risk. I have not experienced a failure. I am reporting because: 1. My vehicle falls within the affected production range. 2. Owners cannot determine whether their vehicle has the original thermoplastic pump or the later metal revision. BMW issued the revised part without changing the part number, and VIN-based parts lookups reportedly return the updated component even when the original is still installed. This deprives owners of any means of assessing their own risk. 3. BMW quietly revised the design to all-metal, indicating the manufacturer identified a durability problem, yet no recall or customer notification has been issued in the United States. 4. Out-of-warranty repair requires removal of the front subframe and eight or more hours of labor. Owners report quotes near $6,000. 5. In South Korea, the Ministry of Land, Infrastructure and Transport opened a formal investigation into this same defect in XXX. BMW Korea then confirmed it is performing this repair free of charge regardless of warranty status. A foreign regulator has already found this serious enough to investigate. I request that NHTSA investigate the B58TU oil pump, determine the failure rate, and evaluate whether a safety recall is warranted. At minimum, owners should be given a reliable method of identifying which pump revision is installed in their vehicle.

The oil level reading is failing at 16% due to an oil pump malfunction. BMW has addressed this on all 2022+ b58 engine but all prior years have the plastic failing oil pump. The had to upgrade it because it cause catastrophic failure to the engine. It creates oil pressure with plastic parts and was upgraded to all metal in 2022. There should be a recall for this part since it can cause catastrophic engine failure at any point anywhere while driving at any speed, slow, fast, speed limit. Doesn’t matter the part can fail and injure or kill people

I am on my third front differential in first in 2023, one in 2025 and now one in 2026. All M50I have this issue but the X5 M model does not.

The A/C evaporator coil failed on my 2020 BMX X5 S40i prior to 27,564 miles. It was taken into the local dealer for evaluation at a cost of $811.33 and UV dye was added with refrigerant, which escaped over a 2 week period. The final diagnosis after a further two weeks and at a cost of $301.38, later confirmed that the evaporator coil needed to be replaced. The BMW Dealer quoted $6,686.35 for the replacement. BMW USA refused to comp or co-op the repair. From my research I see that this is a common failure across a large segment of the BMW range and that a conservative minimum of 771,000 BMW vehicles could be affected and that the cost to cure each vehicle ranges between $4,000 & $8,000. I was very surprised to hear that the was no NHTSA recall nor Class Action Law Suit given the potential number of cases and huge expense to cure

This vehicle has AC problem it’s blowing hot air. It has evaporator leaking. I called multiple shops and they said this problem is very popular for the X5 2019 to 2023 in my car is 2020. Please recall the Evaporator Core problem. It is too dangerous to drive in the car without AC and is too expensive to Have the Evaporator Core replacement.

My 2019 BMW X5 (G05) equipped with the B58 Technical Update (B58TU) engine has experienced a failure / is showing early signs of failure of the engine oil pump assembly.Beginning with the B58TU engine, BMW utilized a variable-displacement oil pump that contains a thermoplastic/plastic internal adjusting ring. This plastic component degrades under normal operating temperatures, resulting in a sudden mechanical failure of the pump. This failure leads to a sudden drop in engine oil pressure, vehicle disablement without sufficient warning, or an inability for the iDrive infotainment system to complete an electronic oil level measurement.A sudden loss of engine lubrication while driving presents a severe safety hazard, capable of immobilizing the vehicle in active traffic. BMW has updated this exact pump part number to utilize all-metal internal carriers on later production runs, but refuses to cover the cost for early out-of-warranty models. I am requesting that the NHTSA open a safety defect investigation into the early B58TU oil pump assembly to force a mandatory safety recall.

It’s a common issue between 2019-2020 where the oil pump which came from factory has plastic impellers which crack/disintegrate causing catastrophic failure to the engine disabling the vehicle the only warning signs before this happens is you cant read oil level and or the car prompts with a warning low oil messages if untreated the car will have catastrophic engine failure with little to no warning the car was mass produced and this is a common issue therefore should be recalled

Low oil pressure light came on during interstate drive. Later analysis at dealership revealed this is related to faulty oil pump with plastic parts in B58 engine.

I replaced my starter prior to a recall that was issued. After the recall, I submitted a claim for reimbursement and the check was issued. Bmw of North American has not updated the recall information associated with my vin. I am this unable to list my vehicle on any rental platform as it is showing a status of an open recall for the starter. The repair was done in September, 2025 and I was reimbursed 3 weeks ago.

Hello, my front differential recently failed on my BMW. based on some research, this appears to be a manufacturing defect that BMW isn't covering affecting many owners of this car.

The AC system blowed hot air. There's must be a problem with this model because my friend also have the 2021 BMW X5 and its AC also have problem. We're suffering from this due to Manufacturing defect.

The contact owns a 2020 BMW X5. The contact received notification of NHTSA Campaign Number: 25V644000 (Electrical System); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure.

For my 2019 BMW X5 SDRIVE40i, The A/C evaporator core failed and began leaking refrigerant, resulting in complete loss of cold air from the A/C system. The vehicle had approximately 50,000 miles. The repair required full dashboard removal and cost approximately 4,500 including a rental vehicle. This appears to be a widespread issue on 2019–2025 BMW X5/X6/X7 models, suspected to be caused by R-1234yf refrigerant incompatibility with the aluminum evaporator core. The leaking R-1234yf refrigerant is also an environmental concern. R-1234yf is a hydrofluorocarbon (HFC) greenhouse gas with a global warming potential significantly higher than CO2. An uncontrolled leak of this refrigerant directly into the atmosphere — due to a defective factory-installed evaporator core — contributes to environmental harm and violates the spirit of EPA regulations governing refrigerant emissions. Consumers should not bear the financial burden of a known manufacturing defect that also results in the uncontrolled release of a regulated substance. BMW has not issued a recall or extended warranty for this component despite widespread owner reports of the same failure. I am requesting NHTSA investigate this issue and compel BMW to issue a formal recall and provide reimbursement to affected owners.

I own a 2019 BMW X5 xDrive40i with the B58 3.0L turbocharged inline-six engine. While driving in Minnesota, the vehicle suddenly displayed an urgent warning stating “oil pressure too low” and instructed me to stop the engine. This occurred while the vehicle was being operated on the road, requiring me to stop driving immediately. The vehicle was later inspected by an authorized BMW dealer. The dealer diagnosed the failure as a defective oil pump and stated that the oil pump must be replaced. The estimated repair cost was approximately $7,500 or more. This is a serious safety concern because a sudden loss of engine oil pressure can lead to engine seizure, loss of motive power, and loss of vehicle control risk depending on traffic conditions. The oil pump is a critical lubrication component and should not fail as a normal wear item. I have found numerous similar owner reports involving BMW B58 oil pump failures, including reports suggesting that cold-weather operation may contribute to or expose the failure. My vehicle is operated in Minnesota, a cold-weather state. The vehicle was inspected by Park Place BMW in Rochester, MN. I am requesting that NHTSA investigate whether this is a safety-related defect affecting 2019 BMW X5 xDrive40i vehicles and other BMW models equipped with the B58 engine.

Front Differential input bearing failure. Sudden jerking that almost causes loss of control. This poses a safety risk. This seems to be a know problem for the 2020 BMW X5 M50i No warning lights and I did not experience hearing any sounds as other have reported.

Plastic oil pump cracking problem is apparently known to BMW, but they haven’t recalled these defective oil pumps leading to engine failure.

Failure of front differential

The contact owns a 2020 BMW X5. The contact stated that the vehicle was taken to a dealer for routine maintenance and it was discovered that there was a coolant leak and that there was a failure with the front differential failure, and that the A/C unit was leaking. The leaking valve was replaced but the differential was not repaired. The contact stated that the failure was a known failure with the vehicle. The manufacturer was made aware of the failure. The failure mileage was 70,000.

Safety Hazard: Oil Pump Failure Leading to Sudden Engine Stall (BMW B58TU engines) Description of Defect: The oil pump module in the 2020 BMW X5 (G05) contains internal plastic components that are prone to thermal degradation and premature failure. These plastic parts can crack or disintegrate, causing a sudden loss of oil pressure. Safety Risk: A failure of the oil pump leads to insufficient lubrication of critical engine components, which can result in a sudden and complete engine seizure while the vehicle is in motion. This causes an immediate loss of propulsion and power steering assist, significantly increasing the risk of a high-speed collision or being stranded in dangerous traffic conditions. Additional Note: This is a known mechanical defect where a critical engine component (oil pump) relies on non-durable plastic materials, creating an unreasonable safety risk for drivers and passengers due to potential catastrophic engine failure without prior warning.

Safety Hazard: Oil Pump Failure Leading to Sudden Engine Stall (BMW G05 X5) Description of Defect: The oil pump module in the 2020 BMW X5 (G05) contains internal plastic components that are prone to thermal degradation and premature failure. These plastic parts can crack or disintegrate, causing a sudden loss of oil pressure. Safety Risk: A failure of the oil pump leads to insufficient lubrication of critical engine components, which can result in a sudden and complete engine seizure while the vehicle is in motion. This causes an immediate loss of propulsion and power steering assist, significantly increasing the risk of a high-speed collision or being stranded in dangerous traffic conditions. Additional Note: This is a known mechanical defect where a critical engine component (oil pump) relies on non-durable plastic materials, creating an unreasonable safety risk for drivers and passengers due to potential catastrophic engine failure without prior warning.

The contact owns a 2020 BMW X5. The contact received notification of NHTSA Campaign Number: 25V644000 (ELECTRICAL SYSTEM); however, the part to do the recall repair was not yet available. The contact stated that the vehicle failed to start. After several attempts, the vehicle started. The check control master warning light was illuminated. The local dealer was not contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The failure mileage was approximately 120,000.

While driving through west Los Angeles, the vehicle suddenly began emitting white smoke from the engine compartment. There were no prior warning lights, messages, or symptoms indicating a problem. The smoke quickly intensified and turned dark. Thick smoke filled the air, and the cockpit, with the smell of toxic fumes. I safely maneuvered to the shoulder and exited the vehicle with my passenger. Flames erupted from the front of the vehicle. We called 911, which dispatched the fire department. The LAFD responded, cutting open the hood in order to extinguish the fire. The vehicle was towed to a yard following the incident. The vehicle and its contents were declared a total loss.   BWM North America dispatched a technician to inspect the vehicle. After inspection, the manufacturer indicated that the starter was the source of the fire. At the time of the incident, the vehicle was subject to a safety recall related to the starter with no remedy available. The failure occurred without warning. Both occupants were exposed to heavy smoke.

I'm reporting a safety issue with BMW vehicles equipped with the B58TU engine (primarily 2019–2021 models). These vehicles use an oil pump containing an internal plastic component that regulates oil pressure. This plastic part is fracturing in the field, leading to sudden loss or instability of oil pressure. Failures commonly occur during cold starts in low temperatures. When the component fails, oil pressure becomes erratic or is lost entirely, often with little to no warning before engine damage or vehicle disablement. Warning signs, when present, include inability to measure oil level electronically, abnormal oil pressure behavior, or sudden drivetrain malfunction warnings. These can quickly progress to engine shutdown or severe engine damage due to oil starvation. My vehicle is currently experiencing all of the described oil pump-related symptoms, including inconsistent electronic oil level readings and drivetrain malfunction warnings consistent with oil pressure instability. This condition creates a serious safety risk. The vehicle can become disabled without warning while driving or shortly after startup. Oil starvation can lead to catastrophic engine failure, especially at highway speeds, where sudden engine shutdown or seizure increases the risk of a crash. Failures are particularly dangerous in winter conditions, when vehicles may become immobilized in traffic or freezing temperatures. Replacement of the pump requires major disassembly and typically costs $6,000–$8,000, assuming no engine damage. Owners cannot determine whether their vehicle has the original plastic component or a revised metal version. BMW’s VIN-based parts lookup now shows only updated components even when original plastic parts remain installed, and the original plastic part number has been removed from dealer systems. Because this defect can cause sudden vehicle disablement and potential catastrophic engine failure without adequate warning.

I am submitting this correspondence as a formal notification of a potential safety-related defect affecting BMW vehicles equipped with the B58 Technical Update (B58TU) engine platform, most commonly model years 2019–2021. The purpose of this communication is to request immediate review under BMW’s vehicle safety defect evaluation process due to an increasing number of oil pump failures capable of causing sudden loss of engine lubrication, unexpected vehicle disablement, and occupant exposure to hazardous conditions. The original B58 engine (B58B30M0, 2015–2017) utilized a conventional mechanically robust gerotor oil pump with predominantly metallic internal construction and demonstrated strong reliability in field operation. This component, constructed from reinforced thermoplastics including PA66-GF materials, operates within a chemically aggressive and thermally cyclic environment involving continuous exposure to engine oil additives, fuel dilution, condensation, and repeated heat cycling. While acceptable under accelerated validation testing, real-world operating conditions increasingly demonstrate premature degradation consistent with polymer embrittlement and fracture. Documented owner and technician reports indicate that under cold-start conditions — particularly in sub-freezing climates — elevated oil viscosity and startup load impose increased mechanical stress on the thermoplastic carrier. Fracture of this internal component allows debris intrusion into the pump mechanism, resulting in unstable oil pressure regulation. Commonly reported precursor symptoms include: • Inability to perform electronic oil level measurement via iDrive • Erratic or oscillating oil pressure behavior • Intermittent lubrication warnings or absence of warning prior to failure • Rapid progression to bearing damage and engine seizure Given the potential for sudden vehicle disablement without adequate warning, I respectfully request BMW of North America initiate a formal inquiry

I am reporting a safety concern involving BMW vehicles equipped with the B58 Technical Update (B58TU) engine, commonly found in model years 2019–2021. These vehicles utilize a variable-displacement engine oil pump containing an internal thermoplastic adjusting component responsible for regulating oil pressure. Field failures are increasingly being reported in which this internal component fractures, resulting in sudden loss or instability of engine oil pressure. The failure frequently occurs during cold-start operation in low ambient temperatures. When the component fails, oil pressure regulation becomes erratic or is lost entirely. In many cases, drivers receive little or no actionable warning prior to engine damage or vehicle disablement. Reported precursor symptoms include inability to electronically measure engine oil level, abnormal oil pressure behavior, or sudden drivetrain malfunction warnings. Failures may rapidly progress to engine shutdown or severe mechanical damage caused by oil starvation. Loss of lubrication can cause the vehicle to become disabled without warning while driving or shortly after startup. This creates a safety hazard, particularly when vehicles become immobilized in active traffic or during winter conditions the cold is when they fail the most, where occupants may be exposed to freezing temperatures while awaiting assistance. Replacement of the oil pump requires extensive disassembly of the vehicle and repairs commonly exceed $6,000–$8,000 for just the pump, assuming the motor is unharmed. Owners are currently unable to determine whether their vehicles contain the original thermoplastic oil pump design or a later revised version utilizing metal internal components, as VIN-based parts information now identifies updated components in the car even when no replacement has occurred and the old components are actually in the car. Also, BMW has actively removed the plastic part number out of all dealer networks as well. Failures have be

Please read file attached

The contact owns a 2020 BMW X5. The contact stated that while the vehicle was parked, there was fluid and lubricant on the ground underneath the vehicle. No warning lights were illuminated. The vehicle was taken to the dealer where it was diagnosed with a detached front differential shaft bearing. In addition, the contact was informed that the front differential shaft bearing caused excessive play in the propeller shaft. The contact was informed that the front differential shaft bearing needed to be replaced. The vehicle was not repaired. The contact stated that the failure was a known failure with the vehicle. The contact stated that the vehicle was serviced by the dealer seven weeks prior to the failure. The manufacturer was made aware of the failure but provided no assistance. The contact was advised to contact the NHTSA Hotline to report the failure. The failure mileage was unknown.

The contact owns a 2020 BMW X5. The contact received notification of NHTSA Campaign Number: 25V644000 (Electrical System); however, the part to do the recall repair was not yet available. The dealer was contacted and confirmed that parts were not yet available for the recall repair. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure.

Vehicle has excessive condensation in driver headlight. Garage kept only. Problem discovered because of parking vehicle outside on driveway while the garage hosted moving boxes. This was the only time this vehicle has spent the night outside.

Was driving at normal interstate speed when I received a warning on my dashboard to pull over and turn off engine —- low engine pressure, immediately. Call a tow. I immediately pulled over, turned off my car and contacted a tow. My vehicle was towed to the BMW dealership. I received an update that my oil pump failed. It’s almost $6k to replace and then stated not sure if that’ll truly fix the problem and to change the engine $28k. I began to do research and this is a known problem. Many owners have this problem- BMW is aware and began change the plastic part to metal in the subsequent years. I received no warning that it was beginning to fail and it is a safety hazard as I was on the interstate at the time.

My 2020 BMW X5 (VIN available upon request) is subject to safety recall 25V-644 due to a fire risk. The recall has been open since November 2025. BMW has confirmed there was no available remedy for an extended period, and a BMW-coordinated service visit on January 15, 2026 could not be completed due to dealership issues. Despite repeated follow-ups with BMW North America, there has been no confirmed repair date and no consistent transportation support while the safety recall remains unresolved. I am concerned about the prolonged delay in addressing this safety issue.

My steering was what I felt as an affected problem. I was subsequently stuck while out with my one year old in the cold 10/31/2024. Eventually the car started again but I had what felt like steering issues (i.e. dragging/shuttering) thereafter. I was told that there were no issues aside from the power steering which completely failed and was replaced. Not until 1 year later when I insisted that the issue continued did the dealership give me an idea of what it could be despite them knowing about the SIB the entire time. There were warning lamps that came on I'm just not sure if any of those lights were the actual undiagnosed issue pertaiing to my transfer case needing to be completely replaced. Either way the dealersihp sandbaged me and only diagnosed the transfer case replacement after I was 1 month out of warranty 11/2025 quoting me with a $10,552.19. repair cost.

The contact owns a 2020 BMW X5. The contact received notification of NHTSA Campaign: 25V644000 (Electrical System); however, the part to do the recall repair not available. The local dealer was contacted and confirmed that parts were not available. The vehicle was not diagnosed or repaired. The manufacturer was made aware of the issue; however, no assistance was provided. The contact had not experienced a failure.

The safety risk arises from inaccurate federal recall records maintained by BMW of North America. My vehicle had a safety recall for starter replacement (Recall 25V-644). This recall repair was already completed by an authorized BMW dealer, and the starter was replaced under warranty. However, BMW continues to list the recall as OPEN with “Remedy Not Available.” This creates a safety risk because inaccurate recall records may lead to improper vehicle safety status, incorrect regulatory reporting, and potential refusal of assistance if a starter-related failure or no-start condition occurs in the future. The problem has been confirmed by an authorized BMW dealer, and I have official service documentation showing that the recall repair was completed. The vehicle was inspected and repaired by BMW of Gwinnett Place. No warning lights were present after the repair. This complaint is not about a new mechanical failure, but about BMW’s failure to accurately update and close a completed safety recall, which misrepresents the vehicle’s safety status.